Paradyne 5011 Installation Instructions Manual

Brand: Paradyne

Model: 5011

Type: Installation Instructions Manual

This manual is also suitable for

5020-A2-GN10-20

March 1998

Hotwire 5020 POTS Splitter Central Office

Installation Instructions

Document Number 5020-A2-GN10-20

March 1998

About the Hotwire 5020 RADSL POTS Splitter

The Hotwire RADSL System enables simultaneous high-speed digital data

access and analog voice service over the same twisted-pair telephone line. The

simultaneous access to RADSL (Rate Adaptive Digital Subscriber Line) and

POTS (Plain Old Telephone Service) requires the installation of a POTS splitter

at both ends of the local loop; i.e., at the central office (CO) and at the customer

premises (CP).

The POTS splitter filters out the DSL signal and allows the POTS frequencies to

pass through. Each central office POTS splitter card contains 12 filters to serve

12 local loops with DSL-based service and POTS. The POTS splitter card is a

passive device and requires no power. The POTS splitter chassis is shipped

separately from the POTS splitter card(s). Two chassis are available:

 Single-card chassis which can be placed on a tabletop or installed in a rack.

 Six-card chassis which must be installed in a commercial EIA-standard

19″ or 23″ rack or cabinet.

Before You Begin

Consider the following before installing the POTS splitter:

 Installation Site

The location should be well-ventilated, clean, and free of environmental

extremes. Allow clearance at the front of the POTS splitter chassis to provide

access to the cables.

 Cabling

Three Telco 50-conductor cables are used to connect to the three interfaces

on the POTS splitter card. The location of the system hardware affects the

length of the three cables.

Cables and Hardware You Need

For each POTS splitter card, obtain three Telco 50-conductor cables with

50-position amphenol-type connectors at the appropriate length based on cabling

requirements in your environment. A Y-cable is available for the DSL connection.

Refer to

Cabling Overview

, page 11, and

Connector Pin Numbers,

page 17.

5020-A2-GN10-20

March 1998

Hotwire 5020 POTS Splitter Card Package Checklist

Verify that your POTS splitter card package contains the following:

 POTS splitter card

 Plastic bag with three of each item:

— Plastic tie-wrap anchors

— #4-40 x 1/4″ screws

— #4-40 x 1/4″ jack screws

—8″ cable tie wraps

 Warranty card

Single-Card 5011 POTS Splitter Chassis Package Checklist

Verify that your single-card POTS splitter chassis package contains the following:

 Single-card POTS splitter chassis

 Two brackets for 19″ racks and two brackets for 23″ racks

 Small plastic bag with:

— Six #10-32 x 1/4″ Phillips flat-head mounting screws

— Four #10-32 x 1/2″ Phillips-head mounting screws

— Four #12-24 x 1/2″ Phillips-head mounting screws

— Four #12-24 speed nuts

— Four black rubber feet

 Warranty card

97-15497

CO POTS Splitter

Single-Card Chassis

Placement of

Rubber

Feet

5020-A2-GN10-20

March 1998

Six-Card 5016 POTS Splitter Chassis Package Checklist

Verify that your six-card POTS splitter chassis package contains the following:

- Six-card POTS splitter chassis with five filler panels. Each filler panel is

attached to the chassis with two 1/4-turn fasteners. Keep filler panels

installed in all unused slots.

- Two brackets for 19″ racks and two brackets for 23″ racks

- Small plastic bag with:

— Six #10-32 x 1/4″ Phillips flat-head mounting screws

— Four #10-32 x 1/2″ Phillips-head mounting screws

— Four #12-24 x 1/2″ Phillips-head mounting screws

— Four #12-24 speed nuts

— Four black rubber feet (discard)

- Warranty card

97-15430

CO POTS Splitter

Six-Card Chassis

Filler

Panels

Tools Required

H A small #1 or #2 Phillips screwdriver to tighten the POTS splitter card

fasteners.

H A large #3 or #4 Phillips screwdriver to install the chassis into a rack.

H A flat-blade screwdriver to install the chassis grounding wire.

5020-A2-GN10-20

March 1998

Product-Related Documents

The 5020 CO POTS splitter card works in conjunction with the Hotwire 8540 or

8546 RADSL card in the central office in the 8600 or 8800 DSLAM chassis, and

a POTS splitter and Remote Termination Unit (RTU) at the customer premises.

Refer to the following documents for product-specific information.

Document Number Document Title

5030-A2-GN10

Hotwire 5030 POTS Splitter Customer Premises

Installation Instructions

5034-A2-GN10

Hotwire 5034 Indoor POTS Splitter Customer Premises

Installation Instructions

5038-A2-GN10

Hotwire 5038 Distributed POTS Splitter Customer