Extron TLP 710TV User manual

68-2028-01 Rev. D

01 19

TLP 710MV and TLP 710TV

User Guide

TouchLink

®

TouchLink Touchpanel Control Systems

Safety Instructions • English

WARNING: This symbol,

D

, when used on the product, is intended

to alert the user of the presence of uninsulated dangerous voltage

within the product’s enclosure that may present a risk of electric shock.

ATTENTION: This symbol,

I

, when used on the product, is

intended to alert the user of important operating and maintenance

(servicing) instructions in the literature provided with the equipment.

For information on safety guidelines, regulatory compliances, EMI/EMF

compatibility, accessibility, and related topics, see the Extron Safety and

Regulatory Compliance Guide, part number 68-290-01, on the Extron

website, www.extron.com.

Sicherheitsanweisungen • Deutsch

WARNUNG: Dieses Symbol

D

auf dem Produkt soll den Benutzer

darauf aufmerksam machen, dass im Inneren des Gehäuses dieses

Produktes gefährliche Spannungen herrschen, die nicht isoliert sind

und die einen elektrischen Schlag verursachen können.

VORSICHT: Dieses Symbol

I

auf dem Produkt soll dem Benutzer

in der im Lieferumfang enthaltenen Dokumentation besonders wichtige

Hinweise zur Bedienung und Wartung (Instandhaltung) geben.

Weitere Informationen über die Sicherheitsrichtlinien, Produkthandhabung,

EMI/EMF-Kompatibilität, Zugänglichkeit und verwandte Themen finden Sie

in den Extron-Richtlinien für Sicherheit und Handhabung (Artikelnummer

68-290-01) auf der Extron-Website, www.extron.com.

Instrucciones de seguridad • Español

ADVERTENCIA: Este símbolo,

D

, cuando se utiliza en el producto,

avisa al usuario de la presencia de voltaje peligroso sin aislar dentro del

producto, lo que puede representar un riesgo de descarga eléctrica.

ATENCIÓN: Este símbolo,

I

, cuando se utiliza en el producto,

avisa al usuario de la presencia de importantes instrucciones de uso y

mantenimiento recogidas en la documentación proporcionada con el

equipo.

Para obtener información sobre directrices de seguridad, cumplimiento

de normativas, compatibilidad electromagnética, accesibilidad y temas

relacionados, consulte la Guía de cumplimiento de normativas y seguridad

de Extron, referencia 68-290-01, en el sitio Web de Extron,

www.extron.com.

Instructions de sécurité • Français

AVERTISSEMENT : Ce pictogramme,

D

, lorsqu’il est utilisé sur

le produit, signale à l’utilisateur la présence à l’intérieur du boîtier du

produit d’une tension électrique dangereuse susceptible de provoquer

un choc électrique.

ATTENTION : Ce pictogramme,

I

, lorsqu’il est utilisé sur

le produit, signale à l’utilisateur des instructions d’utilisation ou de

maintenance importantes qui se trouvent dans la documentation

fournie avec le matériel.

Pour en savoir plus sur les règles de sécurité, la conformité à la

réglementation, la compatibilité EMI/EMF, l’accessibilité, et autres sujets

connexes, lisez les informations de sécurité et de conformité Extron,

réf. 68-290-01, sur le site Extron, www.extron.com.

Istruzioni di sicurezza • Italiano

AVVERTENZA: Il simbolo,

D

, se usato sul prodotto, serve ad

avvertire l’utente della presenza di tensione non isolata pericolosa

all’interno del contenitore del prodotto che può costituire un rischio di

scosse elettriche.

ATTENTZIONE: Il simbolo,

I

, se usato sul prodotto, serve ad

avvertire l’utente della presenza di importanti istruzioni di funzionamento

e manutenzione nella documentazione fornita con l’apparecchio.

Per informazioni su parametri di sicurezza, conformità alle normative,

compatibilità EMI/EMF, accessibilità e argomenti simili, fare riferimento

alla Guida alla conformità normativa e di sicurezza di Extron, cod. articolo

68‑290‑01, sul sito web di Extron, www.extron.com.

Instrukcje bezpieczeństwa • Polska

OSTRZEŻENIE: Ten symbol,

D

, gdy używany na produkt, ma na celu

poinformować użytkownika o obecności izolowanego i niebezpiecznego

napięcia wewnątrz obudowy produktu, który może stanowić zagrożenie

porażenia prądem elektrycznym.

UWAGI: Ten symbol,

I

, gdy używany na produkt, jest przeznaczony do

ostrzegania użytkownika ważne operacyjne oraz instrukcje konserwacji

(obsługi) w literaturze, wyposażone w sprzęt.

Informacji na temat wytycznych w sprawie bezpieczeństwa, regulacji wzajemnej

zgodności, zgodność EMI/EMF, dostępności i Tematy pokrewne, zobacz Extron

bezpieczeństwa i regulacyjnego zgodności przewodnik, część numer 68-290-01,

na stronie internetowej Extron, www.extron.com.

Инструкция по технике безопасности • Русский

ПРЕДУПРЕЖДЕНИЕ: Данный символ,

D

, если указан

на продукте, предупреждает пользователя о наличии

неизолированного опасного напряжения внутри корпуса

продукта, которое может привести к поражению электрическим

током.

ВНИМАНИЕ: Данный символ,

I

, если указан на продукте,

предупреждает пользователя о наличии важных инструкций по

эксплуатации и обслуживанию в руководстве, прилагаемом к

данному оборудованию.

Для получения информации о правилах техники безопасности,

соблюдении нормативных требований, электромагнитной

совместимости (ЭМП/ЭДС), возможности доступа и других вопросах

см. руководство по безопасности и соблюдению нормативных

требований Extron на сайте Extron: www.extron.com, номер по

каталогу - 68-290-01.

安全说明 • 简体中文

警告： D产品上的这个标志意在警告用户该产品机壳内有暴露的危险电压，

有触电危险。

注意：I 产品上的这个标志意在提示用户设备随附的用户手册中有

重要的操作和维护(维修）说明。

关于我们产品的安全指南、遵循的规范、EMI/EMF 的兼容性、无障碍

使用的特性等相关内容，敬请访问 Extron 网站 www.extron.com，参见 Extron

安全规范指南，产品编号 68‑290‑01。

Safety Instructions

安全記事 • 繁體中文

警告: D 若產品上使用此符號，是為了提醒使用者，產品機殼內存在著

可能會導致觸電之風險的未絕緣危險電壓。

注意I 若產品上使用此符號，是為了提醒使用者，設備隨附的用戶手冊中有

重要的操作和維護（維修）説明。

有關安全性指導方針、法規遵守、EMI/EMF 相容性、存取範圍和相關主題的詳細

資訊，請瀏覽 Extron 網站：www.extron.com，然後參閱《 Extron 安全性與

法規遵守手冊》，準則編號 68‑290‑01。

安全上のご注意 • 日本語

警告: この記号 D が製品上に表示されている場合は、筐体内に絶縁されて

いない高電圧が流れ、感電の危険があることを示しています。

注意: この記号 I が製品上に表示されている場合は、本機の取扱説明書に

記載されている重要な操作と保守(整備)の指示についてユーザーの注意

を喚起するものです。

安全上のご注意、法令遵守、EMI/EMF適合性、その他の関連項目に

ついては、エクストロンのウェブサイト www.extron.com より

『Extron Safety and Regulatory Compliance Guide』 (P/N 68‑290‑01) をご

覧ください。

안전 지침 • 한국어

경고: 이 기호 D, 가 제품에 사용될 경우, 제품의 인클로저 내에 있는

접지되지 않은 위험한 전류로 인해 사용자가 감전될 위험이

있음을 경고합니다.

주의: 이 기호 I, 가 제품에 사용될 경우, 장비와 함께 제공된 책자에

나와 있는 주요 운영 및 유지보수(정비) 지침을 경고합니다.

안전 가이드라인, 규제 준수, EMI/EMF 호환성, 접근성, 그리고 관련 항목에

대한 자세한 내용은 Extron 웹 사이트(www.extron.com)의 Extron 안전 및

규제 준수 안내서, 68-290-01 조항을 참조하십시오.

Copyright

Trademarks

All trademarks mentioned in this guide are the properties of their respective owners.

The following registered trademarks®, registered service marks(SM), and trademarks(TM) are the property of RGBSystems, Inc. or

Extron Electronics (see the current list of trademarks on the Terms of Use page at www.extron.com):

Registered Trademarks

(

®

)

Cable Cubby, ControlScript, CrossPoint, DTP, eBUS, EDID Manager, EDID Minder, Extron, Flat Field, FlexOS, Glitch Free, Global Configurator,

Global Scripter, GlobalViewer, Hideaway, HyperLane, IPIntercom, IPLink, Key Minder, LinkLicense, LockIt, MediaLink, MediaPort,

NetPA, PlenumVault, PoleVault, PowerCage, PURE3, Quantum, Show Me, SoundField, SpeedMount, SpeedSwitch, StudioStation,

SystemINTEGRATOR, TeamWork, TouchLink, V-Lock, VideoLounge, VN-Matrix, VoiceLift, WallVault, WindoWall, XTP, XTP Systems, and ZipClip

Registered Service Mark

(SM)

: S3 Service Support Solutions

Trademarks

(

™

)

AAP, AFL (Accu-Rate Frame Lock), ADSP (Advanced Digital Sync Processing), Auto-Image, AVEdge, CableCover, CDRS (Class D

Ripple Suppression), Codec Connect, DDSP (Digital Display Sync Processing), DMI (Dynamic Motion Interpolation), DriverConfigurator,

DSPConfigurator, DSVP (Digital Sync Validation Processing), eLink, EQIP, Everlast, FastBite, FOX, FOXBOX, IP Intercom HelpDesk, MAAP,

MicroDigital, Opti-Torque, PendantConnect, ProDSP, QS-FPC (QuickSwitch Front Panel Controller), Room Agent, Scope-Trigger, ShareLink, SIS,

Simple Instruction Set, Skew-Free, SpeedNav, Triple-Action Switching, True4K, Vector™ 4K, WebShare, XTRA, and ZipCaddy

FCC Class A Notice

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to part15 of the FCC rules. The ClassA limits provide reasonable

protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and,

if not installed and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a residential area is

likely to cause interference. This interference must be corrected at the expense of the user.

NOTES:

• This unit was tested with shielded I/O cables on the peripheral devices. Shielded

cables must be used to ensure compliance with FCC emissions limits.

• For more information on safety guidelines, regulatory compliances, EMI/EMF

compatibility, accessibility, and related topics, see the Extron Safety and

Regulatory Compliance Guide on the Extron website.

Battery Notice

This product contains a battery. Do not open the unit to replace the battery. If the

battery needs replacing, return the entire unit to Extron (for the correct address, see the

Extron Warranty section on the last page of this guide).

CAUTION: Risk of Explosion if Battery is replaced by an Incorrect Type. Dispose of Used

Batteries According to the Instructions.

ATTENTION : Risque d’explosion. Ne pas remplacer la pile par le mauvais type de pile.

Débarrassez-vous des piles utilisées selon le mode d’emploi.

Conventions Used in this Guide

Notiﬁcations

In this user guide, the following are used:

WARNING: Potential risk of severe injury or death.

AVERTISSEMENT : Risque potentiel de blessure grave ou de mort.

CAUTION: Risk of minor personal injury.

ATTENTION : Risque de blessuremineure.

ATTENTION:

• Risk of property damage.

• Risque de dommages matériels.

NOTE: A note draws attention to important information.

Software Commands

Commands are written in the fonts shown here:

^AR Merge Scene,,Op1 scene 1,1 ^B 51 ^W^C

[01] R 0004 00300 00400 00800 00600 [02] 35 [17] [03]

E

X!

*

X1&

*

X2)

*

X2#

*

X2!

CE

}

NOTE: For commands and examples of computer or device responses

mentioned in this guide, the character “0” is used for the number zero and “O”

represents the capital letter “o”.

Computer responses and directory paths that do not have variables are written in the font

shown here:

Reply from 208.132.180.48: bytes=32 times=2ms TTL=32

C:\Program Files\Extron

Variables are written in slanted form as shown here:

ping xxx.xxx.xxx.xxx —t

SOH R Data STX Command ETB ETX

Selectable items, such as menu names, menu options, buttons, tabs, and field names are

written in the font shown here:

From the File menu, select New.

Click the OK button.

Specifications Availability

Product specifications are available on the Extron website, www.extron.com.

Extron Glossary of Terms

A glossary of terms is available at www.extron.com/technology/glossary.aspx.

Contents

Introduction ....................................................1

About the TLP 710MV and TLP 710TV ............ 1

Features .......................................................... 1

Requirements .................................................. 2

Computer .................................................... 2

Other Hardware ........................................... 2

Application Diagram ........................................ 3

Installation Overview .....................................4

Panel Features ...............................................6

TLP 710MV Front Panel Features

and Operations ............................................... 6

Reset Buttons and LED ............................... 7

TLP 710MV Rear Panel Features

and Connections ............................................ 8

TLP 710TV Front Panel Features

and Operations ............................................. 13

TLP 710TV Rear Panel Features

and Connections .......................................... 14

Initial Calibration .........................................18

Accessing the Internal On-screen Menus ....... 18

Main Screen .................................................. 18

Volume Screen .............................................. 19

Time Screen .................................................. 20

Network Screen ............................................. 20

Video Screen ................................................. 21

Touch Calibration Screen ............................... 21

Conﬁguration Software ...............................22

Conﬁguration Software .................................. 22

Software Installation....................................... 23

Downloading and Installing Software

from the Extron Website ........................... 23

Touchpanel Web Pages ................................. 24

Updating Firmware ........................................ 27

Downloading Firmware .............................. 27

Using Extron Firmware Loader ................... 27

Using GUI Conﬁgurator .............................. 28

Using the Touchpanel Webpage ................ 28

Using GUI Conﬁgurator .................................. 29

Using Global Conﬁgurator .............................. 34

Mounting ......................................................39

Rack Mounting the TLP 710MV ..................... 39

Rack Mounting the TLP 710MV ................. 39

Underwriters Laboratories Guidelines

for Rack Mounting .................................... 39

Wall Mounting the TLP 710MV ...................... 40

Wall Mounting the TLP 710MV

with a Wall Box ............................................. 41

Furniture Mounting the TLP 710MV ............... 41

Desktop Mounting the TLP710TV ................. 42

Placement without a Mounting Kit ............. 42

Placement with a Kensington

Security Lock............................................ 42

Mounting with a Swivel Mount Adapter ...... 43

Removing the TLP 710TV Base for

VESA Mounting ............................................ 43

VESA Mounting the TLP 710TV ..................... 45

Reset Modes ................................................ 46

Use Factory Firmware .................................... 46

Activation ................................................... 46

Result ........................................................ 46

Run or Stop Events ....................................... 47

Activation ................................................... 47

Result ........................................................ 47

Reset All IP Settings ...................................... 47

Activation ................................................... 47

Result ........................................................ 47

Reset to Factory Defaults .............................. 48

Activation ................................................... 48

Result ........................................................ 48

TLP 710MV and TLP 710TV • Contents vii

TLP 710MV and TLP 710TV • Contents viii

Introduction

This guide describes the function, installation, and operation of the TouchLink TLP710MV

and TLP 710TV touchpanels. Unless otherwise stated, the terms TLP 710 Series, TLP

710, and TouchLink touchpanel refer to both models.

This section contains the following information:

• About the TLP 710MV and TLP 710TV

• Features

• Requirements

• Application Diagram

About the TLP 710MV and TLP 710TV

Each unit has a 7-inch widescreen LCD display with a resolution of 800x480. The screen

displays graphic objects and text, which are associated with user-defined functions.

The touch overlay screen allows the user to initiate or activate functions by touching the

objects on the screen.

The screen layout is designed with the Extron GUI Configurator software. The functions

are assigned to the screen objects with the Extron Global Configurator software. The

user can define the graphics and the functions associated with those graphics, providing

versatility and adaptability to the configuration and control of an AV system.

A motion sensor, light sensor, and a speaker provide sleep mode, auto dimming, and

audible feedback.

The TLP 710MV can be wall or rack mounted.

The TLP 710TV can be placed on a desktop or VESA

®

mounted on a wall or furniture,

using an appropriate mounting kit (not provided).

Features

• 7-inch color LCD touchscreen — displays a range of graphic objects and text on a

800x480 resolution screen with 18-bit color depth.

• Full-motion video display — for preview and monitoring using Extron twisted pair

technology.

• Built-in MTP —a twisted pair receiver accepts either S-video or composite video

signals over standard CAT 5-type cable. Provides integration ﬂexibility and aids in

cable management by minimizing the number of connections at the touchpanel.

• Compatible with all IP Link control processors.

• Power over the Ethernet (PoE) — allows the touchpanel to receive power and

control over a single CAT 5-type cable, eliminating the need for a local power supply -

power injector included.

• Fully configurable — using Extron GUI Conﬁgurator and Global Conﬁgurator

with ready-to-use templates.On-screen graphics and text, as well as the functions

associated with them, can be easily changed to adapt the control panel to the

evolving needs of the system, avoiding the need for additional control modules.

• Ethernet connection — provides an inexpensive, easily installed cabling option for

connecting products located anywhere else on the network.

TLP 710MV and TLP 710TV • Introduction 1

• Supports the Extron Control App.

• Configurable red and green status lights — can be used to indicate room

availability.

• Light sensor — adjusts screen brightness as the ambient room lighting changes.

• Energy-saving features:

- Adjustable sleep timer puts touchpanel into sleep mode

- Motion detector wakes touchpanel

• Automatic clock synchronization with controller — for accurate time and date

display

• Built-in speaker — provides audio for the full-motion video preview and audible

feedback from button presses.

• Multiple mounting options

The TLP 710MV mounts on a wall, lectern, or any flat surface.

The TLP 710TV can sit on a tabletop or be wall-mounted with a VESA mounting kit. It

has a weighted base that allows up to 45° of tilt. Kensington lock support allows the

touchpanel to be locked to a table or other flat surface.

• Color options — The TLP 710MV is available in black or white.

Requirements

Computer

For a complete list of the requirements for running GUIConfigurator or Global

Configurator, see www.extron.com for that software.

NOTES:

• Use Global Conﬁgurator 3.3 or a later version and GUIConﬁgurator1.3 or a later

version to conﬁgure the TLP 710MV or TLP710TV.

• The TLP 710MV and TLP 710TV are not compatible with Global Conﬁgurator

Plus and Professional or GUI Designer.

Other Hardware

An Extron IP Link control processor must also be connected to the same network domain

as the TouchLink touchpanel. Go to www.extron.com for a list of suitable control

processors.

NOTE: The TLP 710MV and TLP 710TV are compatible only with IP Link control

processors.

TLP 710MV and TLP 710TV • Introduction 2

Application Diagram

This diagram shows the TLP 710MV. The TLP 710TV can be used for similar applications.

RS232/RS422

REMOTE

1.3A MAX.

100-240V , 50-60Hz

US

LISTED

IT23

I.T.E.

®

L

1

R

L

2

R

L

3

R

L

4

R

L

5

R

L

6

R

L

7

R

L

8

R

OUTPUTS

L

1

R

L

2

R

L

3

R

L

4

R

ADDRESS

INPUTS

ADDRESS

DVI-D INPUTS

5

6

7

8

1

2

3

4

1

2

3

4

DVI-D OUTPUTS

LAN

ACT

LINK

RESET

INPUT

LAN

POWER

12V

500mA

MAX

1 2 3 4

COM 3

IR

3

S G

TX RX

4

RELAY

3

4

COM1

TX RX

RTS CTS

COM 2

IR

1

S G

TX RX

2

RELAY

1

2

XPA 1002

1 2

LIMITER/PROTECT

SIGNAL

OVER

TEMP

INP

UTS

LOCAL OUTPUT

AUDIO

DVI-D

DTP DVI 301 Tx

POWER

12V

0.4A MAX

DVI 201 Tx

RS-232

PASS THRU

TxRx

DDC ROUTE

1

2

REMOTE

SPARE

LOCAL

SINGLE LINK

ON

1

2

DVI 201 Rx SERIES

DVI-D OUTPUT

CONTROL

PASS-THRU

Tx

Rx

L

R

OUTP

UTS

DVI-D

AUDIO

DTP DVI 301 Rx

Extron

TLP 710MV

7" TouchLink

Touchpanel

Digital

Input

Extron

XPA 1002

Power Amplier

TCP/IP

Network

Lighting

System

Screen

Control

Laptop

Blu-ray Player

Extron

SMX 200

Matrix Switcher

Motion

Detector

RS-232

IR Control

to Blu-ray

Relay

Extron

IR Emitter

Extron

DTP DVI

301 Rx

Receiver

Extron

DTP DVI

301 Tx

Transmitter

Projector

Extron

IPL 250

IP Link Control

Processor

Figure 1. TLP 710MV Application Diagram

TLP 710MV and TLP 710TV • Introduction 3

Installation

Overview

1. Before starting, download and install the latest versions of the following software:

 Global Configurator — for setting up and conﬁguring the control processor and

touchpanel.

 GUI Configurator — for designing layouts for Extron TouchLink touchpanels and

third party touch interfaces.

See Configuration Software on page 22.

NOTE: These touchpanels and controllers are not compatible with

GUI Designer or Global Conﬁgurator Plus and Professional.

2. Obtain the following network information from your network administrator:

 DHCP status (on or off). If DHCP is off, you will also require

 IP address

 Subnet mask

 Gateway

 User name — by default these are either admin or user.

 Passwords — by default these are either extron (for admin) or the ﬁeld is left

blank (for user).

 MAC address — make a note of the touchpanel MAC address.

3. Mount and cable the units:

ATTENTION:

• Do not power on the touchpanels or control processors until you have read

the Attention notice on page 9 (12 VDC power supply) or on page 12 (PoE

injector).

• Ne branchez pas les écrans tactiles ou les contrôleurs avant d’avoir lu

les mises en garde page 9 (source d’alimentation 12VCC) ou page 12

(injecteur PoE).

 Mount the units. There are several mounting options for the touchpanels (see

Mounting on page 39).

 Connect cables to the touchpanels (see TLP 710MV Rear Panel Features

and Connections on page 8 or TLP 710TV Rear Panel Features and

Connections on page 14).

 Connect the power cords and power on all devices. See Network LAN and

Power over Ethernet connector on page 11 (for the TLP 710MV) or on

page 16 (for the TLP 710TV). See Power connector on page 9 (for the

TLP 710MV) or page 14 (for the TLP 710TV).

TLP 710MV and TLP 710TV • Installation Overview 4

4. Set up the Touchpanels for Network Communication:

 Connect the PC that you will use for setup, the control processor, and the

touchpanel to the same Ethernet subnetwork.

NOTE: The TLP 710 series of touchpanels are not compatible with the

Extron Pro series of devices.

 Use the Setup Menu (see Accessing the Internal On-screen Menus on

page 18) to set the DHCP status and, if necessary, the IP address, subnet

mask, gateway, and related settings for the touchpanel.

5. Configure the Touchpanels — see Using GUI Conﬁgurator on page 29 and

Using Global Conﬁgurator on page 34. The GUI Conﬁgurator Help File and the

Global Conﬁgurator Help File provide detailed information.

TLP 710MV and TLP 710TV • Installation Overview 5

Panel Features

This section describes:

• TLP 710MV Front Panel Features and Operations

• TLP 710MV Rear Panel Features and Connections

• TLP 710TV Front Panel Features and Operations

• TLP 710TV Rear Panel Features and Connections

TLP 710MV Front Panel Features and Operations

Extron

AA

B

C

D

E

F

G

H

A

Motion sensor (see below)

E

LCD screen on page 7

B

Microphone (see below)

F

Connection status LED on page 7

C

Speaker (see below)

G

Bezel on page 7

D

Programmable LEDs (see below)

G

Light sensor on page 7

Figure 2. TLP 710MV Front Panel

A

Motion sensor — is capped with a small Fresnel lens that focuses light onto the

sensor. When no motion has been detected for a user-deﬁned period of time, the

unit enters sleep mode. When motion is detected by the sensor, the screen display is

restored and active.

B

Microphone — is located below the LCD screen.

C

Speaker — one located under the screen, on the left side of the panel, provides

audible feedback for the user.

D

Programmable LEDs — one on each top corner can be programmed to provide

system feedback. They light red or green and can blink or light solid in response to

user-deﬁned events.

TLP 710MV and TLP 710TV • Panel Features 6

E

LCD screen (see ﬁgure 2) — has a 800x480 resolution with a touch overlay. A

graphical user interface, designed using GUI Conﬁgurator, displays buttons, text,

or icons on the screen (see Using GUI Conﬁgurator on page 29). These are

conﬁgured for a range of user-deﬁned functions, using Global Conﬁgurator (see Using

Global Conﬁgurator on page 34).

F

Connection status LED (see ﬁgure 2) — is unlit during normal operation. Blinks red

if the connection to the IP Link controller is lost.

G

Bezel (see ﬁgure 2) — removable with Extron removal tool (provided). Clips ﬁt into

attachment points on the front panel (see ﬁgure 4 below) and snap into place.

HH

Figure 3. TLP 710MV Top View

H

Light sensor (see ﬁgure 2) — is on top of the display frame. The sensor monitors

the level of ambient light and adjusts the screen brightness. The sensor can be

viewed only from above the panel.

Reset Buttons and LED

The front bezel is removed by inserting the Extron removal tool into the slots on the top of

the unit. Behind the bezel are two buttons and an LED.

AA

D

B

C

Figure 4. TLP 710MV Front Panel with the Bezel Removed

A

Bezel attachment points

B

Menu button — activates the on-screen menus for calibrating the unit (see

Accessing the Internal On-screen Menus on page 18).

C

Reset button — allows the unit to be reset in any of four different modes. For further

information see Reset Modes on page 46.

D

Reset LED — provides feedback about the reset status when the user presses the

reset button. For further information see Reset Modes.

TLP 710MV and TLP 710TV • Panel Features 7

TLP 710MV Rear Panel Features and Connections

Extron

AA

B

C

D

A

Power connector on page 9

C

MTP input on page 11

B

MTP signal adjustments on

page 10

D

Network LAN and Power over

Ethernet connector on page 11

Figure 5. TLP 710MV Rear Panel Features

TLP 710MV and TLP 710TV • Panel Features 8

A

Power connector (see ﬁgure 5 on page 8) — Connect the 2-pole, 3.5 mm

captive screw connector from the 12 VDC, 1.0 A power supply (not provided) to the

power supply socket on the rear panel. Ensure the connections have the correct

polarity as shown below.

NOTE: Extron recommends using the Power over Ethernet power supply. The

12VDC, 1.0 A power supply should be used only for setup or troubleshooting.

If you do use a 12 VDC 1.0 A power supply, Extron recommends the PS 1210C.

Power Receptacle

Captive Screw Connector

AC Power Cord

Ground

+12 VDC

External

Power Supply

(12 VDC, 1 A )

SECTION A–A

Ridges

Smooth

Power Supply

Output Cord

AA

3/16"

(5 mm) Max.

Figure 6. Power Supply Connection

ATTENTION:

• Always use a power supply provided by or speciﬁed by Extron. Use of an

unauthorized power supply voids all regulatory compliance certiﬁcation and may

cause damage to the supply and the end product.

• Utilisez toujours une source d’alimentation fournie ou recommandée par Extron.

L’utilisation d’une source d’alimentation non autorisée annule toute conformité

réglementaire et peut endommager la source d’alimentation ainsi que le produit

ﬁnal.

• If not provided with a power supply, this product is intended to be supplied by a

UL Listed power source marked “Class 2” or “LPS” and rated output 12 VDC,

minimum 1.0 A or 48 VDC (PoE), minimum 0.35 A.

• Si le produit n’est pas fourni avec une source d’alimentation, il doit être alimenté

par une source d’alimentation certiﬁé UL de classe 2 ou LPS, avec une tension

nominale 12 Vcc, 1 A minimum, ou 48Vcc (PoE), 0,35A minimum.

• Extron power supplies are certiﬁed to UL/CSA 60950-1 and are classiﬁed as LPS

(Limited Power Source). Use of a non-LPS or unlisted power supply will void all

regulatory compliance certiﬁcation.

• Les sources d’alimentation Extron sont qualiﬁées UL/CSA60950-1 et sont

classéesLPS(LimitedPowerSource). L’utilisation d’une source d’alimentation

non-listée ou non-listéeLPS annulera toute certiﬁcation de conformité

réglementaire.

TLP 710MV and TLP 710TV • Panel Features 9

ATTENTION:

• Unless otherwise stated, the AC/DC adapters are not suitable for use in air

handling spaces or in wall cavities. The power supply is to be located within the

same vicinity as the Extron AV processing equipment in an ordinary location,

Pollution Degree 2, secured to the equipment rack within the dedicated closet,

podium, or desk.

• Sauf mention contraire, les adaptateurs AC/DC ne sont pas appropriés pour

une utilisation dans les espaces d’aération ou dans les cavités murales. La

source d’alimentation doit être située à proximité de l’équipement de traitement

audiovisuel dans un endroit ordinaire, avec un degré2 de pollution, ﬁxé à un

équipement de rack à l’intérieur d’un placard, d’une estrade, ou d’un bureau.

• The installation must always be in accordance with the applicable provisions of

National Electrical Code ANSI/NFPA 70, article 725 and the Canadian Electrical

Code part 1, section 16.

• Cette installation doit toujours être en accord avec les mesures qui s’applique

au National Electrical Code ANSI/NFPA70, article725, et au Canadian Electrical

Code, partie1, section16.

• The power supply shall not be permanently ﬁxed to building structure or similar

structure.

• La source d’alimentation ne devra pas être ﬁxée de façon permanente à une

structure de bâtiment ou à une structure similaire.

• The length of the exposed wires in the stripping process is critical. The ideal

length is 3/16 inches (5 mm). If the wires are any longer, the exposed wires may

touch, causing a short circuit between them. If they are any shorter, the wires can

be easily pulled out even if tightly fastened by the captive screws.

• La longueur des câbles exposés est primordiale lorsque l’on entreprend de les

dénuder. La longueur idéale est de 5mm (3/16inches). S’ils sont un peu plus

longs, les câbles exposés pourraient se toucher et provoquer un court circuit.

S’ils sont un peu plus courts, ils pourraient sortir, même s’ils sont attachés par les

vis captives.

• Do not tin the wires. Tinned wires are not as secure in the captive screw terminals

and could pull out.

• Ne pas étamer les câbles. Les câbles étamés ne sont pas aussi bien ﬁxés dans

les terminaisons des à vis captives et pourraient sortir.

B

MTP signal adjustments (see ﬁgure 5 on page 8) — Use a small screwdriver

to adjust these three MTP signal variables: S-video luminance gain (VID/Y), S-video

chrominance gain (C), and sharpness (S). For composite video signals, the gain is

controlled by the VID/Y adjustment. Insert a small Phillips head screwdriver into the

recess and turn clockwise to increase adjustment or counterclockwise to decrease.

TLP 710MV and TLP 710TV • Panel Features 10

C

MTP input (see ﬁgure 5 on page 8) — A twisted pair cable, terminated with an

RJ-45 connector, provides video and audio input from an Extron MTP transmitter. The

MTP port is in the top surface of the recessed area.

ATTENTION:

• The left RJ-45 connector on the back of the TLP 710MV (with the yellow and

green LEDs) must be connected to a network. The right RJ-45 connector

must be connected to an Extron MTP Transmitter. The MTP and LAN use

different voltages; switching the connectors will damage the touchpanel.

• Le connecteur RJ-45 gauche situé au dos du TLP 710MV (avec des LED

jaunes et vertes) doit être connecté à un réseau. Le connecteur RJ-45 droit

doit être connecté à un émetteur MTP Extron. Le MTP et le LAN utilisent des

tensions différentes; permuter les connections risque d’endommager l’écran

tactile.

D

Network LAN and Power over Ethernet connector (see

ﬁgure 5) — These touchpanels connect to a network using a

twisted pair cable, terminated with an RJ-45 connector. The

LAN port is in the top surface of the recessed area.

The network port has two LEDs. The green LED lights

steadily to indicate that the touchpanel is connected correctly

to a network. The yellow LED flashes to indicate that data is being passed to or from

the touchpanel.

An Extron IP Link control interface must also be connected to the same network

domain. See www.extron.com for suggested models.

The connector can also be used with the provided XTP Pi 100 PoE power injector.

You can use any power injector that is PoE Plus IEEE 802.3at compliant, but Extron

recommends the XTP PI 100 power injector, which is shown in figure 7 below. Your

power injector may look different.

To use a power injector: Connect a straight-through Ethernet cable to the power

supply and a switch or router. This cable carries network information from the switch

or router to the power supply input. A second straight-through cable carries the

network information and 48VDC from the power supply to the touchpanel. Connect

the IEC power cord to a 100 VAC to 240 VAC, 50-60 Hz power source.

100-240V

~

50-60Hz

0.4A MAX

XTP

PWR

XTP PWR

To network switchTo TLP 710MV

or TLP 710TV

Figure 7. Connecting the Power over Ethernet Power Supply

LAN

Activity LED

Link LED

RJ-45 Port

TLP 710MV and TLP 710TV • Panel Features 11

ATTENTION:

• The TLP 710MV and TLC 710TV are intended for connection to a Power over

Ethernet circuit for intra-building use only and are considered to be part of a

Network Environment 0 per IEC TR62101.

• Le TLP 710MV et le TLC 710TV sont conçu pour une connexion à un circuit PoE

pour une utilisation intérieure seulement et est considéré comme faisant partie

d’un environnement réseau 0 par IECTR62101.

• If not provided with a power supply, this product is intended to be supplied by a

UL Listed power source marked “Class 2” or “LPS” and rated output 12 VDC,

minimum 1.0 A or 48 VDC (PoE), minimum 0.35 A.

• Si le produit n’est pas fourni avec une source d’alimentation, il doit être alimenté

par une source d’alimentation certiﬁé UL de classe 2 ou LPS, avec une tension

nominale 12 Vcc, 1 A minimum, ou 48Vcc (PoE), 0,35A minimum.

• This product is intended for use with a UL Listed power source marked “Class 2”

or “LPS” and rated 12VDC, minimum 1.0 A. or 48 VDC (PoE), minimum 0.35 A.

• Ce produit est destiné à une utilisation avec une source d’alimentation listéeUL

avec l’appellation «Classe2» ou «LPS» et normée 12Vcc, 1,0A minimum ou

48Vcc (PoE), 0,35A minimum.

• Extron power supplies are certiﬁed to UL/CSA 60950-1 and are classiﬁed as LPS

(Limited Power Source). Use of a non-LPS or unlisted power supply will void all

regulatory compliance certiﬁcation.

• Les sources d’alimentation Extron sont qualiﬁées UL/CSA60950-1 et sont

classéesLPS(LimitedPowerSource). L’utilisation d’une source d’alimentation

non-listée ou non-listéeLPS annulera toute certiﬁcation de conformité

réglementaire.

• Unless otherwise stated, the AC/DC adapters are not suitable for use in air

handling spaces or in wall cavities. The power supply is to be located within the

same vicinity as the Extron AV processing equipment in an ordinary location,

Pollution Degree 2, secured to the equipment rack within the dedicated closet,

podium, or desk.

• Sauf mention contraire, les adaptateurs AC/DC ne sont pas appropriés pour

une utilisation dans les espaces d’aération ou dans les cavités murales. La

source d’alimentation doit être située à proximité de l’équipement de traitement

audiovisuel dans un endroit ordinaire, avec un degré2 de pollution, ﬁxé à un

équipement de rack à l’intérieur d’un placard, d’une estrade, ou d’un bureau.

• Power over Ethernet (PoE) is intended for indoor use only. It is to be connected

only to networks or circuits that are not routed to the outside plant or building.

• L’alimentation via Ethernet (PoE) est destinée à une utilisation en intérieur

uniquement. Elle doit être connectée seulement à des réseaux ou des circuits qui

ne sont pas routés au réseau ou au bâtiment extérieur.

• The installation must always be in accordance with the applicable provisions of

National Electrical Code ANSI/NFPA 70, article 725 and the Canadian Electrical

Code part 1, section 16.

• Cette installation doit toujours être en accord avec les mesures qui s’applique

au National Electrical Code ANSI/NFPA70, article725, et au Canadian Electrical

Code, partie1, section16.

• The power supply shall not be permanently ﬁxed to building structure or similar

structure.

• La source d’alimentation ne devra pas être ﬁxée de façon permanente à une

structure de bâtiment ou à une structure similaire.

TLP 710MV and TLP 710TV • Panel Features 12

Page is loading ...

Extron TLP 710TV User manual

Extron TLP 710TV User manual

in other languages

Related papers

Other documents