Premier 120341LF Installation guide

Premier
Brand
Premier
Model
120341LF
Category
Sanitary ware
Type
Installation guide

This manual is also suitable for

Shut off water supply at angle stop. Remove
old faucet. Clean sink surface in preparation
for new faucet.
Important: After installation is completed,
remove aerator. Turn on water supply and
allow both hot and cold water to run for at
least one minute each. While water is
running, check for leaks. Replace aerator.
3.
2.
4.
1.
INSTALLATION STEPS: Two handle lavatory faucet
Cleaning:
To maintain and protect the fine luster of all products, clean with a soft, damp cloth
only. DO NOT USE detergents or cleansers as they may harm the protective finish.
INSTALLATION
Making the waterline connections:
Use 1/2 in. I.P.S. faucet connections (2, not
included), or use the coupling nuts (3, not
included) with a 3/8 in. O.D. ball-nose riser (1,
not included). Before tightening the faucet
connector to the water supply, apply a second
wrench to the supply tube fitting. This will
prevent the supply tube from moving or
twisting when tightening the faucet connector.
Do not overtighten.
5.
9.
Attach horizontal rod (1) to strap (2) using
clip (3). Insert lift rod (4) into strap and
tighten screw (5). Connect assembly to drain
(6).
10.
2
1
6
5
3
Model Number: 120341LF & 120342LF & 110704
Slide hot and cold end valves through sink
mounting holes. Make sure long tubes are
installed away from spout. Note: Hot side
end valve is labeled. Secure end valves
with washers and nuts. Hand tighten nuts
onto shank. Lock nuts into position by
tightening screws.
Place spout assembly through mounting hole
in sink. Secure spout with rubber washer,
metal washer and nut.
Align tabs (1) and tabs (2) on quick
connects (3). Push quick connects firmly
upward and snap onto receiving tube tab
(1). Pull down moderately to ensure each
connection has been made.
3
1
2
Hole for lift rod
Sink
Washers
4
3
2
1
Brand Lavatory Faucets
7
8
3
11
10
4
5
6
9
2
1
Remove the stopper (1) and the flange (2). Screw
the brass nut (3) all the way down. Push the plastic
washer (4) and the gasket (5) down. Unscrew the
pivot nut (6) from the pop-up body (7) and remove
the seal washers (8). Take off the spring clip (9)
from the horizontal rod (10). Remove the tailpiece
(11) from the pop-up body (7).
6.
4
Apply the silicone to the underside of the flange (2).
Insert the pop-up body (1) into the drain hole from
below sink. Screw the flange (2) into the pop-up body
(1). With the pivot hole (3) facing toward faucet, Use
groove joint pliers to tighten the nut (4), do not over
tighten. Do not turn the pop-up while tightening the
nut, or sealant may not seal drain. Clean excess
putty.
Apply thread sealant tape to the top threads of
the tailpiece (5) in a clockwise direction, as shown
and hand tighten.
5
4
3
1
2
7.
3
2
1
8.
Install the horizontal rod (2) and the stopper (3) as
shown (4). Hand tighten the pivot nut (1).
Tools:
Adjustable wrench
Groove joint pliers
Pipe wrench
Screwdriver
Thread sealant tape
Basin wrench
Plumber's putty
17
5
6
4
11
8
2
10
1
9
3
7
120341LF & 120342LF & 110704
12
14
15
13
18
16
6
Cartridge(H)
Cartridge(C)
1
1
3
4
1325 1
Handle Screw & Screw Cap (C)
5
4
Bonnet Nuts
1
41
1
328
Handle Screw & Screw Cap (H)
3
2
Handle Assembly
1
1
326
327
MODEL NO.110704
PART DESCRIPTION
NO. QTY.
PART NO.
Flanges & Seats
7
Cap
331
1
Mounting Kit
169
14
Lift Rod & Lift Knob
O-Rings
18
17
Brass Pop-Up
Hose Assembly
16
Block
15
129
1
11
Spout Seat
Mounting Kits
13
12
Aerator
O-rings
10
9
330
122
329
45
Washer
44
8
130
131
332
333
MODEL NO.120341LF
PART DESCRIPTION
Handle Screw & Screw Cap (H)
Handle Screw & Screw Cap (C)
9
O-rings
14
17
Hose Assembly
18
Lift Rod & Lift Knob
Brass Pop-Up
16
O-Rings
Block
15
Mounting Kits
12
Mounting Kit
Spout Seat
13
11
Aerator
10
5 Bonnet Nuts
Cap
7
Washer
8
6
Cartridge(H)
Cartridge(C)
2
Flanges & Seats
3
Handle Assembly
4
NO.
1
45
1
169
1
1
131
1
1
47
124020
1
130
129
1
122
123
1
168
1
41
1
1
1
43
44
1
3
4
1
34 1
167
119
1
1
PART NO.
33 1
QTY.
45
9
O-rings
14
169
Hose Assembly
17
Brass Pop-Up
18
Lift Rod & Lift Knob
15
Block
16
O-Rings
131
51
124011
130
129
12
Mounting Kits
13
Spout Seat
Mounting Kit
10
Aerator
11
122
124
170
41
1
Bonnet Nuts 5
8
Washer
Cap
7
Cartridge(C)
Cartridge(H)
6
1
44
1
1
50
4
3
1
PART DESCRIPTION
Handle Screw & Screw Cap (H)
Handle Screw & Screw Cap (C)
2
Flanges & Seats
Handle Assembly
3
4
NO.
1
36 1
171 1
172
1
PART NO.
QTY.
35 1
MODEL NO.120342LF
www.premierfaucet.com, [email protected]
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
  • Page 1 1
  • Page 2 2

Premier 120341LF Installation guide

Premier
Brand
Premier
Model
120341LF
Category
Sanitary ware
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents