Honeywell 8734001 Installation guide

Page 1

Models 8734001, 8734101, 8734301, 8734401

Read this manual carefully before installing and operating!

Installation & Operation Guide

Electronic Entry Lock with Lever

ENGLISH

Page 2

Index

INSTALLATION INSTRUCTIONS

Package Contents / Tools Required...........................................................Page 1

Prepare Door and Jamb...............................................................................Page 2

Adjusting Latch / Installing Latch...............................................................Page 3

Installing Exterior Assembly........................................................................Page 4

Installing Interior Assembly.........................................................................Page 5

Reversible Lever Handles............................................................................Page 6

Installing Interior Assembly Cont................................................................Page 7

OPERATION INSTRUCTIONS

Exterior Assembly Overview.......................................................................Page 8

Locking and Unlocking / Changing Programming Code /

Adding User Codes......................................................................................Page 9

Deleting User Codes / Automatic Lock Function /

Temporarily Disable Auto Lock...................................................................Page 10

Vacation Mode / Secure Lock-out Period / Sound ON and Off /

Restore Factory Settings / Low Battery Warning.....................................Page 11

Consumer Friendly Message Guide / Installation Trouble Shooting.......Page 12

Consumer Assistance.................................................................................Page 13

Programming Record..................................................................................Page 14-15

Template.......................................................................................................Page 17

Limited Warranty..........................................................................................Page 19

Page 1

INSTALLATION INSTRUCTIONS

Package Contents

Tools Required

Tools Required for Installation

on Pre-drilled Doors:

•PhillipsScrewdriver

Tools Required for Installation

on Doors That Require Drilling:

•Drill

•TapeMeasure

•Pencil

•2-1/8”(54mm)DrillHoleSaw

•1”(25mm)Drill

•1/16”(2mm)Drill

•Chisel

•Hammer

•PhillipsScrewdriver

DONOTRETURNTOSTORE!Ifanypartsaremissingordamaged,

pleasecallCustomerServicetollfreeat1-800-860-1677 Ext. 1801 (M-F 8am – 5pm PST)

Strike Plate

Latch(Adjustable)

2-3/8”(60mm)to2-3/4”(70mm)

5/16”(8mm)Screws-2ea.

3/4”(19mm)Screws-5ea.

ExteriorAssembly

Entrykeys(2ea.)

7/8”(22mm)Screws-2ea.

1”(25mm)Screw-1ea.

Interior Assembly

Mounting Plate

Page 2

NOTE: For installation on doors with pre-drilled holes skip to 4e.

1. TEMPLATE

a. Cut out template printed on page 17 of this Manual

 (Figure1a).

b. Foldtemplateandplaceondoor36”(915mm)from

  thegroundasmarked(Figure1b).

2. MARK THE DOOR FOR DRILLING

b. Mark center hole on door edge through guide on

 templatefor1”(25mm)latchbolt(Figure2a).

a. Mark center hole on door face through guide on

  templatefor2-3/8”(60mm)or2-3/4”(70mm)

  backset(Figure2b).

3. DRILL AND CHISEL DOOR

 a.Drill2-1/8”(54mm)holethroughdoorfaceasmarked

  forlockset(Figure3a).

 b.Drill1”(25mm)holeincenterofdooredgefor

  Latch(Figure3b).

c. Insert Latch in hole keeping it parallel to

  faceofdoor.MarkoutlineandremoveLatch

  (Figure3c).

 d.Chisel1/8”(3mm)deeporuntillatchfaceisush

  withdooredge(Figure3d).

4. MARK AND DRILL DOOR JAMB

a. MarkcenterholeonedgeofjambevenwiththecenteroftheLatchBoltondoor

 edge.(Figure4a).

 b.Drill1”(25mm)hole1-3/16”(30mm)deepindoorjamboncentermark 

 (Figure4b).

 c.OutlineoutsideedgesofStrikePlate(Figure4c).

 d.Chisel1/8”(3mm)deepforStrikePlateoruntilush(Figure4d).

 e.InstallStrikePlateusingtwo3/4”(19mm)screwsprovided(Figure4e).

PREPAREDOORANDJAMB

Figure4a Figure4b

Figure4c Figure4e

Figure4d

NOTE: For Drive in Latch, drill hole size indicated on template and press

until it is ush with door edge.

Figure1a

Figure2a Figure2b

Figure3a

Figure3c

Figure1b

Figure3b

Figure3d

Page 3

5. INSTALLING THE LATCH (need phillips head screwdriver)

 a.Makesurethefaceplatesitsushwiththedoor.Donotforce

 theLatchintothemortiseush.Chiseloutexcessmaterialif

  necessaryforausht(Figure5a).

 b.Usingtwo3/4”(19mm).screwsprovided,screwtheLatchintothe

 doorwithahandheldscrewdriver.DONOTOVERTIGHTEN

 (Figure5b).

ADJUSTINGLATCH

NOTE: Latch is shipped with the backset set at 2-3/8” (60mm)

Measurethebackset(backsetisdistancebetweenedgeofthedoorandthe

centerofLock).

TO CONVERT FROM 2-3/8” (60mm) BACKSET TO 2-3/4” (70mm) BACKSET

TO CONVERT FROM 2-3/4” (70mm) BACKSET TO 2-3/8” (60mm) BACKSET

2-3/8"(60mm )

PULL

2-3/4"(70mm)

PUSH

NOTE: Curved part of Latch always faces

curved portion of Strike Plate

INSTALLINGLATCH

Figure5a

Figure5b

Page 4

NOTE: Tailpiece must be

positioned vertically

INSTALLINGEXTERIORASSEMBLY

Rubber

Gasket

Control

Wire

Tailpiece

(Vertical)

Latch

Hole

Figure6a-b Figure6c

7. SECURING THE EXTERIOR ASSEMBLY TO THE DOOR

 a.Fromthesidemarked“Thissideagainstdoor”,

route the Control Wire through the rectangular

  slotintheMountingPlate(Figure7a).

 b.PlaceMountingPlateagainstdoorwithtailpiecepassing

  throughthecenterholeinthethreeholeset(Figure7b).

 c.SecuretheMountingPlatetotheExteriorAssemblyusing

  two7/8”(22mm)Screws(Figure7c).

 d.HandtightenwithaPhillipsScrewdriverleavingloosely

 connected(Figure7d).

 e.CheckthattheRubberGasketisproperlyalignedandcorrectasnecessary(Figure7e).

 f.Checkverticalalignmentofthelock(Figure7f).

 g.TightensecurelywithahandheldPhillipsScrewdriver.DO NOT OVER TIGHTEN

8. OPTIONAL INSTALLATION

 a.Usinga1/16”(2mm)drillbit,drillapilotholeinyourdoor

  usingtheMountingPlateupperholeasaguide(Figure8a).

b. Insert one 3/4”(19mm)screwandtighten.

Mounting Plate

3/4”(19mm)screw

(OptionalInstallation)

7/8”(22mm)screws

Control Wire

Figure8a

Figure7a-7f

NOTE: Rotate lever to ensure the latch is opening and closing easily.

6. INSTALLING THE EXTERIOR ASSEMBLY

Note: WorkwiththeDoorOpenforeasyaccess.Toaccessthemountingplate,unpack

theInteriorAssemblyandremovethebatterycoverbyslidingthecoverupward.Locate

thescrewsholdingtheMountingPlatetotheInteriorAssembly.Removethescrewsto

releasetheMountingPlatefromtheInteriorAssembly.

 a.UnpacktheExteriorAssembly.Usecaretonotscratchthegreencircuitboard

during handling and installation.

 b.CheckthattheRubberGasketisproperlyseatedontheExteriorAssembly 

 (Figure6a-b).

 c.InserttheExteriorAssemblyontothedoorwiththetailpiecegoingthroughthe

Latch spindle in the VERTICAL POSITION. Route the Control Wire through

  thedoorovertheLatch(Figure6c).

Page5

INSTALLINGINTERIORASSEMBLY

9. ATTACH THE CONTROL WIRE TO THE INTERIOR ASSEMBLY

 a.UsecaretoattachtheControlWiremaleplugtotheInteriorAssemblyfemale

  socketconnector(Figure9a).

 b.DonotforcetheControlWiremaleplugintotheInteriorAssemblyfemale

  socketconnector(Figure9b).

 c.TheControlWiremaleplughastwoalignmenttabsonthesmoothsideofthe

  plugwhichisthetopoftheplug(Figure9c).

 d.TheControlWiremaleplugisinsertedwiththesmoothsideupintotheInterior

 Assemblyfemalesocketconnector(Figure9d).

10. ATTACH THE INTERIOR ASSEMBLY TO DOOR

 a.PositiontheInteriorAssemblyoverthetailpieceandpushtheInteriorAssembly

 againstthedoor(Figure10a).

 b.Usingtwo5/16”(8mm)screws and one 1”(25mm)screw, attach

 theInteriorAssemblytotheMountingPlate.DO NOT OVER TIGHTEN SCREWS

(Figure10b).

5/16”(8mm)screws

1”(25mm)screw

NOTE: Lock and unlock using Interior Lever to see if the

latch is opening and closing easily.

Figure10a-b

Figure9a-d

Interior Wire

Connector

Plug

Page6

11. REMOVING AND REVERSING LEVER HANDLES

 a.MakesuretheDoorLockisintheunlockedpositionandthenreleasecatchby

 insertingLockStickintotheslotontheundersideoflevers(Figure11a).

 b.Removebothleverhandlesfromthebasesbypullingawayfromdoorwhenthecatch

 isreleased(Figure11b).

 c.Switchtheleverhandlestotheoppositeside(Figure11c).

12. REPLACING LEVER HANDLES

 a.Makesurelockcylinderisinlinewithhandle(Figure12a).

b. Replace handles by sliding onto the bases until the catch pins are engaged.

 (Figure12b).

REVERSIBLELEVERHANDLES

Reversiblehandle

Interchangeable

Cylinder

Lock Stick

Figure11a-c

Figure12a Figure12b

Page 7

13. Installing Batteries

 a.Insert4AAhighqualityAlkalinebatteriesintotheBatteryCompartmentinthe

 directionnoted+/-ontheCompartment.TheLockwillbeep2times,thekeypad

 willilluminateblue,andtheHoneywellbuttonwillashgreentwicetosignifythat

 ithasreceivedpower(Figure13a).

 b.SlidetheBatteryCoverdownintothetrackontheInteriorAssemblytocover

thebatteries(Figure13b).

14. Testing Lock

 WiththeDoorOpen

 a.TesttheLockusingtheInteriorLever.TheLatchshouldmovesmoothly.

 b.TestthelockusingtheKeypad.Tolockpressandthenpress“1234”

to unlock.

INSTALLINGINTERIORASSEMBLY(CONT.)

Override

AccessKey

Exterior Assembly

Interior Assembly

Interior

Lever

Battery

Cover

Light Indicator

Keypad

NOTE: Do not touch the Keypad until the blue light turns off.

Do not use rechargeable batteries or non-alkaline batteries.

Figure13a-b

INSTALLATION OVERVIEW

Strike Plate

BatteryCover

InteriorAssembly

Keys

Exterior

Assembly

Rubber Gasket

Tailpiece

Mounting Plate

Latch

5/16”(8mm)screws

Optional

3/4”(19mm)screw

3/4”(19mm)screws

7/8”(22mm)screws

1”(25mm)Screw

Page 8

OPERATION INSTRUCTIONS

ExteriorAssemblyOverview

Indicator light

Green

•IndicatesSuccessfulProgrammingStep

•IndicatesUnlockingisSuccessful

Red

•IndicatesFailedProgrammingStep

•IndicatesLockingisSuccessful

Electronic lock requires (4) High Quality

AA Alkaline batteries. When all 4 batteries

are installed in the correct position, hear 2

beeps and the keypad will illuminate blue.

DO NOT TOUCH the keypad until the keypad

stops illuminating.

Lock-Usedtolockdoor

Clear -Usedtoclearwrongkeypadentries

Unlock-Usedtounlockdoor

Programming -Usedinprogrammingsteps

5 Seconds -Completealltheprogrammingstepsintheprogrammingmodewithin5seconds.

Clear -Usethekeytoclearentriesincaseawrongbuttonispushed.

Lock button

Unlockbutton

FactorySettings

The lock comes factory preset with a:

Please change the Programming

Code and the User Code

as soon as possible after installation

to insure security.

Programming code - 123456

User code - 1234

User ID - 01

ID

PC

UC

Batteries(notincluded)

Programming Symbols

Lock/Clear

Unlock/Programming

Programming Code

User Code (4-8 digits)

User ID (01-50, 2 digits)

ID

PC

UC

Programming Tips

Page9

TO UNLOCK THE LOCK

UsingKeypad:EnteravalidUserCode(defaultcodeis1234)andpressandhear

1 beep and lights green.

TO LOCK THE LOCK

UsingKeypad:Pressandthenhear2beepsandlightsred.

CHANGE CURRENT OR PRESET PROGRAMING CODE

FactorydefaultProgrammingCode=123456,thisisthemasterpasswordfor

yourlock.Allprogrammingfunctionsrequirethiscode.Followthebelowsequenceto

changetheProgrammingCodetoyourcustom6digitcombination.

TO ADD A NEW USER CODE(youcanaddupto50newusercodes)

TheUserCodemustbea4-8digitcombination.EachUserCodeisthenlinked

toaUserID(whichisanynumberbetween01-50)toidentifyanindividualUser

Code.(UserID1-9shouldbeenteredas01-09sotheyare2digits).

Hear 1 beep and Light Indicator illuminates green.

RecordNewandChangedCodesonProgrammingRecordlocatedonPage14.

Hear 1 beep and Light Indicator illuminates green.

NOTE:WhenaNEWUSERCODEisset,thedefaultfactorycode(1234)isdeleted

for safety.

RecordNewandChangedCodesonProgrammingRecordlocatedonPage14.

123456   08 56785678

Forexample:toaddtheUserID-08toUserCode-5678,enterthefollowing:

4newRe-enter

1Re-enter

LockingandUnlocking

Changing Programming Code

AddingUserCodes

ID

UC UC

UC

PC

PC PC

PC

Page 10

DELETE ONE EXISTING OR PRESET USER CODE

TheunitcomeswithafactoryUserID=01forUserCode=1234.

IMPORTANT:Todelete1UserCode,thelockmusthavemorethan1UserCode

in its database.

SET OR CANCEL AUTO LOCK

Youcansetthelocktoautomaticallycloseaftereachtimethelockisopened.Time

valuerange=20-900seconds,enterthefollowing:

DELETE ALL USER CODES

IMPORTANT:thiswilldeletetheusercodesbutnottheprogrammingcode,enter

thefollowing.

Hear 1 beep and Light Indicator illuminates green.

SetAutoLock:

Hear 1 beep and Light Indicator illuminates green.

To cancel Auto Lock set the time to 00, enter the following:

CancelTimeValueAutoLock:

Hear 1 beep and Light Indicator illuminates green.

2Existing re-enter

5TimeValue

500

3re-enter

DeletingUserCodes

AutomaticLockFunction

PC

PC PC

ID

UC

ID ID

DISABLE:

WhileinAuto-Lockmode,unlockdoorusing,within10secondsyoumustturnthe

lockingknobbyhandtothelockedposition,waitmorethan2secondsthenturnthe

lockingknobbacktotheunlockposition.TheAuto-Lockmodeisnowdisabled.

RESTORE:

TorestoretheAuto-Lockfuntion,youcanturnthelockingknobbyhandtothelocked

position,waitmorethan2secondsorpressthe

Lock button on the keypad.

TemporarilyDisableAuto-Lock

PC

Page 11

NOTE: If you only press the for more than 3 seconds but

do not input

PC

, the system will remain in Vacation Mode.

WarningsoundsandLEDashesredafter4incorrectcodeattempts:Keypadshuts

downfor30seconds.

To reset the lock to the original factory settings including the Programming Code

andallUserCodesremoveonebatteryfor10seconds.Reinsertthebatteryand

waitforalongandshortbeep.Press3timeswithin3seconds.Thelockwillbeep

andthelightindicatorwillturngreen.

BeepsandLEDashesredfor5seconds.Replacewithgoodqualityalkalinebatteries.

Note:RemovingbatteriesdoesnoteraseactiveProgrammingorUserCodes.

WithVacationModeenabled,thesystementersintolow-powercomsumptionmode.

Duringthismode,allbuttonsandfunctionsincludingtheremotecontrollwillbeinvalid

untiltheyarere-enabled(seestepsbelow).

ENABLE:

DISABLE:

TodisabletheVacationMode,youmustpressandholdformorethan3seconds,

theninputtounlockthedoor.VacationModeisnowdisabled.

SecureLock-outPeriod

RestoreFactorySettings

LowBatteryWarning

VacationMode

UC

PC

Hear 1 beep and Light Indicator illuminates green then lock door

10 1

PC

Youcan“mute”orturnthe“soundon”onyourlockbyenteringthefollowing.

(Factorysettingissoundon).

SoundOff(1)-LightIndicatorilluminatesgreen.

SoundOn(2)-Hear1beepandLightIndicatorilluminatesgreen.

61or2

SoundOnandOff

PC

1=SoundOff

2=SoundOn

Page 12

NOTE:Whenbatteryisunderlowvoltage,thelockwillgivethe(LowBatteryWarning:Beepsand

LEDashesredfor5seconds).Duringthistimeyourlockcanstillwork.Howeveroncethevoltage

islowerthan4.3V(calledSuper-LowVoltage),theoperationofthelockingandunlockingwillnot

work,usermustreplacebatteriesimmediately.

Unlock/Validprogramming: 1longbeepandLEDilluminatesgreen

Lock: 2shortbeepsandLEDilluminatesred

InvalidProgramming: 2shortbeepsandLEDashesredtwice

LowVoltage: Beepsfor5seconds

(7/9timesdependsonoperationisunlock/lock)

SuperLowVoltage: 4shortbeepsandLEDashesredfourtimes

4Incorrectcodeentryattempts: 2shortbeepsandLEDilluminatesredeachattempt

Poweron: 1longbeepand1shortbeepandLEDilluminatesgreen

ChipReset: 1longbeepand1shortbeepandLEDilluminatesgreen

(mayoccurseveraltimesoronceinawhile)

LockError: 3longbeepsLEDashesredthreetimes

RepeatoperationafterLockError: 2shortbeepsthreetimesLEDashesredsixtimes

CONSUMERFRIENDLYMESSAGEGUIDE

INSTALLATIONTROUBLESHOOTING

Issue Solution

Lockwillnotfunction

electronically

•Checkthatallbatteriesarefreshhighquality

AlkalineBatteries

•Checkforproperpolarity(+-)ofallbatteries

•CheckthattheControlWireisattachedtothe

InteriorAssembly

Latch is sticking. Installationscrewsofthelockmaybetootightandhaveto

be loosened

•RemoveInteriorAssembly

•SlightlyloosentheMountingPlateScrews

•LockandunlockusingtheKey

•ReattachControlWireandInteriorAssembly

Page 13

Unlock/Validprogramming: 1longbeepandLEDilluminatesgreen

Lock: 2shortbeepsandLEDilluminatesred

InvalidProgramming: 2shortbeepsandLEDashesredtwice

LowVoltage: Beepsfor5seconds

(7/9timesdependsonoperationisunlock/lock)

SuperLowVoltage: 4shortbeepsandLEDashesredfourtimes

4Incorrectcodeentryattempts: 2shortbeepsandLEDilluminatesredeachattempt

Poweron: 1longbeepand1shortbeepandLEDilluminatesgreen

ChipReset: 1longbeepand1shortbeepandLEDilluminatesgreen

(mayoccurseveraltimesoronceinawhile)

LockError: 3longbeepsLEDashesredthreetimes

RepeatoperationafterLockError: 2shortbeepsthreetimesLEDashesredsixtimes

CONSUMERASSISTANCE

EMAIL: [email protected]

WEBSITE: www.honeywellsafes.com

ADDRESS: Consumer Assistance Dept.

LH Licensed Products, Inc., 860 East Sandhill Avenue Carson, CA 90746 USA

TELEPHONE: US/Canada 1-800-860-1677 Ext. 1801 (Toll Free)

Mexico 01-800-288-2872 After English voice recording stops you must then enter 800-

860-1677 to complete your call. (Toll Free)

Australia 0011-800-5325-7000 (Toll Free)

Germany/New Zealand 00-800-5325-7000 (Toll Free)

Other Countries XX*-310-323-5722 (Toll Charges Apply)

XX*- Dial U.S. Country Code rst

CALL CENTER HOURS: US/Canada 8am – 5pm (Pacic**) Mon – Fri

(Subject to change)

CALL BACK HOURS: Other Countries 8am – 5pm (Pacic**) Mon – Fri

(Subject to change)

* Insert correct Country Code

** Local Time based on Los Angeles California USA

INTERNATIONAL CALL BACK HOURS:

If you need to speak with a consumer assistant and cannot contact us during the Call

Center hours above, please send an email or leave a telephone message, including your

Name, Telephone Number and the best time for us to contact you during the Call Back

hours above and we will make our every eort to contact you and help answer any of

your questions or concerns.

Page is loading ...

Page 17

2-3/8” (60mm) BACKSET

2-3/4” (70mm) BACKSET

THEN DRILL 1” (25mm) HOLE

IN CENTER DOOR OF EDGE

2” (50mm) IN DEPTH

MARK

FOR 1-3/4”

(45mm)

DOOR

DRILL

2-1/8” (54mm)

HOLE

MARK

FOR 1-3/8”

(35mm)

DOOR

IMPORTANT!

PLACE TEMPLATE

ON HIGH EDGE OF

DOOR BEVEL

PLACETOP

36”(915mm)

ABOVEFLOOR

Page 18

BACK OF

TEMPLATE

Page19

Limited Lifetime Mechanical and Finish Warranty / 1 Year Limited Electronics Warranty

Thisproductcomeswithalimitedlifetimemechanicalandnishwarrantyandaoneyearlimited

electronicswarrantytotheoriginalresidentialconsumeragainstdefectsinmaterialand

workmanshipundernormaluseaslongastheoriginalresidentialpurchaseroccupiesthe

residentialpremisesuponwhichtheproductwasoriginallyinstalled.

ORIGINALRESIDENTIALCONSUMER

Thiswarrantyisnottransferable,andappliestotheoriginalpurchaseronly,aslongastheoriginal

purchaseroccupiestheresidentialpremisesuponwhichtheproduct(s)wasoriginallyinstalled.

Proofofpurchase(originalsalesreceipt)andownershipmustaccompanyallwarrantyclaims.

Allnon-homeownerpurchasers(includingpurchasersforindustrial,commercialandbusinessuse)

arenotcoveredunderthetermsofthiswarranty.

WHATISNOTCOVERED

Thiswarrantyisnullandvoidiftheproductwasusedforpurposesforwhichitwasnotdesigned.

ThiswarrantyDOESNOTCOVERnormalwearandtearofpartsordamageresultingfromanyof

thefollowing:negligentuse,misuseorabuseoftheproduct,orusecontrarytoorinviolationof

writteninstructionsprovidedbyLHLicensedProducts,Inc.Further,thiswarrantydoesnotcover

ActsofGod,suchasre,ood,hurricanesandtornadoes.ThiswarrantyDOESNOTCOVER

scratches,abrasions,deteriorationduetotheuseofpaints,solventsoruseofcleaners

containingabrasives,alcoholorothersolvents,whetherperformedbyacontractor,service

company,oryourself.ThiswarrantyDOESNOTCOVERproduct(s)usedincommercial

applications, used in common area applications, disassembly, repair or alteration by anyone other

than LH Licensed Products, Inc., improper installation or exposure to extremes of heat or humidity.

ThiswarrantyDOESNOTCOVERanylosses,injuriestopersonsorlossofproperty,general

damagesorcosts,andshippingandfreightexpensesrequiredtoreturnproduct(s)to

LH Licensed Products, Inc. LH Licensed Products, Inc. shall not be liable for any indirect,

incidental or consequential damages of any nature relating to this lock. LH Licensed Products, Inc.

isalsonotresponsibleforcostsassociatedwithremovingorreinstallingtheproduct.

ADDITIONALTERMS

LH Licensed Products, Inc. does not authorize any person to create for it any obligation or

liabilityinconnectionwiththeProduct.LHLicensedProducts,Inc.’smaximumliabilityhere

under is limited to the original purchase price of the Product. No action arising out of any claimed

breachofthiswarrantybyLHLicensedProducts,Inc.maybebroughtbytheoriginalresidential

purchasermorethanone(1)yearafterthecauseofactionhasarisen.

Page 20

TheHoneywellTrademarkisusedunderlicensefromHoneywellInternationalInc.Honeywell

InternationalInc.makesnorepresentationsorwarrantieswithrespecttothisproduct.

www.honeywellsafes.com

Manufacturedby:

LH Licensed Products, Inc.

860EastSandhillAvenue

Carson,CA90746

Page is loading ...

Page39

THEN DRILL 1” (25mm) HOLE

IN CENTER DOOR OF EDGE

2” (50mm) IN DEPTH

MARK

FOR 1-3/4”

(45mm)

DOOR

DRILL

2-1/8” (54mm)

HOLE

MARK

FOR 1-3/8”

(35mm)

DOOR

IMPORTANT!

PLACE TEMPLATE

ON HIGH EDGE OF

DOOR BEVEL

DU MODÈLE

Distance d'entrée de 2-3/8 po (60MM)

Distance d'entrée de 2-3/4 po (70MM)

PLIEZ ICI SUR LE

BORD DE LA PORTE

MARQUEPOUR

UNEPORTEDE

1-3/4po(45MM)

MARQUEPOUR

UNEPORTEDE

1-3/8po(35MM)

PUISPERCERUNTROU

DE1PO(25MM)TENIRAU

CENTREDELAPORTEÀ2

PO(50MM)DEPROFONDEUR

POURL’INSTALLATIONDELA

SERRURED’ENTRÉEETDES

PÊNESDORMANTS

IMPORTANT:PLACEZ

LEMODÈLESURLE

BORDÉLEVEZDU

BISEAUDELAPORTE

MARQUEZLE

CENTREDUTROU

SURLEDEVANT

DELAPORTE

PLACEZAU

DESSUSÀ36

PO(915MM)

DUSOL

PERCEZUN

TROUDE

2-1/8PO

(54MM)

Page is loading ...

Honeywell 8734001, 8734101, 8734401 Installation guide

Related papers

Other documents