AIC CB214-OT User manual



CB214-OT

Compute Node Barebone

User Manual

Document Number: MAN-00112-A

P/N: H882BB0W40-00000-0



1

Contents

Contents .......................................................................................... 1

Safety Information ...................................................................... 3

About This User Manual ............................................................ 4

Chapter 1. Product Introduction ........................................... 5

1.1 General Information........................................................... 5

1.2 System Specifications ........................................................ 6

1.3 Front View of CB214-OT ..................................................... 8

1.4 Rear View of CB214-OT ...................................................... 8

1.5 Top View of CB214-OT ....................................................... 9

Chapter 2. Hardware Setup ................................................... 10

2.1. Chassis Cover .................................................................... 10

2.2. System Memory ................................................................ 14

2.3. Drive Bays ........................................................................... 16

2.4. Riser Card ........................................................................... 17

2.5. Expansion Slot.................................................................... 18

Chapter 3. Motherboard Settings ....................................... 20

3.1 Motherboard Layout and Connectors ......................... 20

3.2 LEDs ..................................................................................... 26

Chapter 4. BIOS Configuration and Settings ................. 28

4.1 BIOS Setting ....................................................................... 28

4.2 Updating BIOS ................................................................... 30

Chapter 5. BMC Configuration and Settings .................. 32

5.1 Method 1 (Use the BIOS setup) ...................................... 32

5.2 Method 2 (Use a Dos tool - Syscheck) .......................... 34

2

5.3 Connect to BMC .............................................................. 36

5.4. Updating BMC Firmware ................................................. 40

5.5. Updating BMC Configuration ......................................... 41

Chapter 6. Technical Support .............................................. 42

This document contains proprietary information about

AIC products and is not to be disclosed or used except

in accordance with applicable agreements.

3

Safety Information

When installing, operating, or performing maintenance on this equipment, basic safety

precautions, as listed below, should always be followed to reduce the risk of fire, electric

shock, and personal injuries.

 Read and understand all instructions.

 Observe warnings and instructions marked on the product.

 For proper mounting instructions, please consult the User’s Manual provided with

the product.

 Do not place this product on an unstable cart, stand or table which might cause

the product to fall and sustain serious damage.

 Install only equipment identified in the User’s Manual provided with this product.

Use of other equipment might cause improper connection of circuitry that might

lead to fire or personal injuries.

 This product should be operated only from the type of power source indicated on

the marked label. If you are uncertain about the type of power supply in your

area, consult your dealer or the local Power Company.

 Disconnect the power supply module when removing power from the system.

 Unplug this product from the wall outlet before cleaning. Use a damp cloth for

cleaning. Do not use liquid cleaners or aerosol cleaners.

 Do not use this product near a water source such as a wet faucet.

 Never push objects of any kind into this product through open slots as they may

touch dangerous voltage points or short out parts that could result in fire or

electric shock. Never spill liquids of any kind on the product.

 Do not block or cover slots and openings in the unit as they are for ventilation to

protect the unit from overheating. Do not place the product in a built-in

installation unless proper ventilation is available.

 To reduce the risk of electric shock, do not disassemble this product. Service

should only be performed by trained personnel. Opening or removing covers

and/or circuit boards may expose you to electric or other risks. Incorrect

reassembly can cause electric shock when the unit is subsequently used.

 Risk of explosion is possible if battery is replaced with an incorrect type. Dispose

used batteries according to the instruction.

 This product is equipped with a three-wire grounding type plug, a plug with a third

(grounding) pin. This plug is intended to fit only into a grounding type power

outlet. This is a safety feature. If you are unable to insert the plug into the outlet,

contact your electrician to replace the outlet. Do not defeat the safety purpose

by removing the grounding type plug. Do not use a 3-to-2 prong adapter at the

receptacle. Use of this type of adapter may result in risk of electric shock and/or

damage to this product.

4

About This User Manual

This document provides a detailed description of the CB214-OT including:

 The General Features of the Product

 Hardware Setup

 Motherboard Settings

 BIOS Configuration and Settings

 BMC Configuration and Settings

5

Chapter 1.

Product Introduction

1.1 General Information

CB214-OT, a 2U Compute Node Barebone, supports Single socket C32 to support

AMD

®

4100/4200 series processor. CB214-OT has 2 x 2.5” hotswap HDD bays for flexible

storage applications. CB214-OT harnesses MAX I/O™ technology to support 2 OTS

(Off-the-shelf) PCIe X16 cards and 1 HTX card.

System Package Contents

Check your package for the following items:

Motherboard

Octans (PSG-M-OCUP5690-101)

Components

1x 800W 1+1 Hot-swap Redundant Power Supply

2 x hotswap 2.5" SATA/SAS/SSD HDD bays

2 x SAS/SATA Single HDD backplane

2 x MAX I/O Main Riser Card

3 x System Fans

Accessories

2 x Power Cords

2 x Internal SATA Cables

1 x Heatsinks

6

1.2 System Specifications

Dimensions (with chassis ears/protrusions)

W x D x H

mm : 482.6 x 416.4 x 88.8

inches : 19 x 16 x 3.5

Motherboard

Octans (PSG-M-OCUP5690-101)

Processor

Processor Support

Single socket C32 to support AMD

®

4100/4200 series processor

Chipset

Chipset Support

• AMD

®

SR5690 I/O Bridge

• AMD

®

SP5100 Southbridge

System Memory

6 x DIMM slots support up to 64GB of DDR3 800/1066/1333/1600 MHz

Registered ECC memory (recommended) / Unbuffered ECC SDRAM

Front Panel

Controls

• Power ON/OFF

• System ID

• System Reset

• 1 x USB

LEDs

• Power

• System ID

• Alert

Drive Bays

2 x hotswap, fixed 2.5" SATA/SAS/SSD HDD bays

Expansion Slots

• 2 x PCIe X16 slot

• 1 x HTX3 slot

Riser Card (included)

PSG-RC-OC1U-10-101

(PSG Code: PE2U18)

2U Gold-finger X16 to 2 PCIe X16 + HTX3 riser for Octans

SATA/SAS Backplane

SATA/SAS BP

2 x SAS/SATA 6G 2-in-1 backplane

System BIOS

BIOS Type

• AMI EFI BIOS

• SPI (Serial Peripheral Interface) FLASH Interface

BIOS Features

• ACPI 1.0/2.0/3.0

• PXE 2.0

• WOL

• AC loss recovery

• IPMI KCS interface

• SMBIOS 2.0

• Serial console redirection

• USB legacy boot

7

On-Board Devices

SATA

AMD

®

SP5100 SATA2 controller with RAID support

IPMI

Aspeed AST 2050 BMC

• Intelligent Platform Management Interface 2.0 (IPMI 2.0)

• iKVM, Media redirection, IPMI over LAN, Serial over LAN

• SMASH support

Network

Controllers

2 x Intel

®

82574L PCIe single-port GbE controllers

Graphics

Aspeed AST 2050 graphics controller

• 8 MB of system memory

• 1600 x 1200 @ 60 Hz

Super I/O

Nuvoton NTC6627UD (Winbond W83627UHG)

Audio Codec

REALTEK ALC662-GR

Rear I/O

LAN

2 x RJ-45 ports

USB

2 x USB 2.0 ports

2 x USB 3.0 ports

eSATA

1 x eSATA port

VGA

1 x VGA port

Serial Port

1 x DB-9 serial port

Power Supply

800W 1+1 redundant power supply with PMBUS interface

• 90 - 264 VAC full range, 47-63 Hz

System Cooling

System

Cooling

3 x 60x38mm fans

System Management

System

Management

• IPMI 2.0 compliance

• KVM over IP

• Media redirection

• CPU temperature (APML)

• System temperature

• Temperature, fan, voltage,

PSU sensor monitor

• Fan speed detection

• Smart Fan speed control

• System ID / System fail indicator

• SMASH support

• Remote Power ON/OFF/Reset

• SEL message alarm through mail

• SNMP support

Operating Environment

Environmental

Specifications

• Operating Temperature: 0 ~ 35°C

• Operating Altitude Condition: Sea Level

• Storage Temperature: -30°C~70°C

• System Relative Humidity: 5% to 95% (35°C) non-condensing

8

1.3 Front View of CB214-OT

1.4 Rear View of CB214-OT

LED

Icon

Color

System Behavior

Controls

Icon

System Behavior

Power LED

Green

Solid: System On

Off: System Off

Power ON/OFF

Push for Power On or

Off

System ID LED

Blue

System

Identification

Blink: Activity

System ID

Push for ID LED On or

Off

Alert LED

Red

Light: System

Alert

System Reset

Push for System Reset

USB Port

For USB device

connection

800W 1+1

Power supply

2 x RJ-45

ports

VGA port

DB-9 serial port

port

2 x USB3.0

ports

eSATA port

2 x USB2.0 ports

9

1.5 Top View of CB214-OT

The barebone server includes the basic components shown below.

3 x system fans

2 x 2.5” hotswap HDD

Octans MB

800W 1+1

redundant power

supply

Rear I/O

Expansion Slots

10

Chapter 2.

Hardware Setup

This section demonstrates maintenance procedures in replacing a defective part once

the CB214-OT appliance is installed and is operational.

2.1. Chassis Cover

2.1.1 Removing the Chassis Cover

1. Release the screws on the rear panel.

2. Pull the cover back to open the rear cover from chassis.

11

2.1.2 Central Processing Unit (CPU)

2.1.3 Installing the CPU

1. Press the load lever to release the load plate.

2. Lift the load plate.

3. Remove the processor protective cover from CPU socket.

Processor protective cover

Load lever





Load plate

12

4. Align the processor cutouts against the socket notches.

5. Close the load plate & load lever.

Press to close

Cutouts







13

2.1.4 Installing the CPU Heatsink

To install the CPU heatsink:

1. Place the heatsink on top of the CPU, ensuring that the two fasteners match

the holes on the motherboard.

2. Tighten screws on each side of the heatsink, a couple of turns at a time, until

all screws are secure and the heatsink is securely fastened to the chassis.

14

2.2. System Memory

This server board supports up to six DDR3 800/1066/1333 /1600 Registered ECC SDRAM

(recommended)/ Unbuffered ECC SDRAM.

1. Populate DIMMs in the following order:

RDIMM:

DIMM

Numbers

DIMM arrangement

2 DIMMs

CHA

CHB

DIMM2

4 DIMMs

CHA

CHB

DIMM2

DIMM0

DIMM2

DIMM0

6 DIMMs

CHA

CHB

DIMM2

DIMM1

DIMM0

DIMM2

DIMM1

DIMM0

15

UDIMM:

DIMM

Numbers

DIMM arrangement

2 DIMMs

CHA

CHB

DIMM2

4 DIMMs

CHA

CHB

DIMM2

DIMM0

DIMM2

DIMM0

2. Unlock a DIMM socket by pressing the retaining clips outward.

3. Insert module vertically and press down until it snaps into place.

DIMM notch

16

2.3. Drive Bays

2.3.1 Installing or Replacing 2.5” Hot-swap SAS/SATA HDD

1. Release a drive tray by pushing the release button to open the latch

2. Firmly hold the tray latch and pull the drive out of the drive slot.

3. Place one 2.5” HDD on the tray and then secure it with four screws on both

sides of HDD tray.





17

4. Slide the drive into the drive slot until it is fully seated. Make sure the drive

tray is correctly secured in place when its front edge aligns with the bay

edge. Close the latch until it clicks to lock the drive.

5. Repeat steps from1 to 4 to install the oher HDD.

2.4. Riser Card

RISER CARD PN (PSG CODE)

DESCRIPTION

PSG-RC-OC1U-10-101(PE2U18)

Max IO supports two PCIeX16 , one HTX

RISER CARD DIAGRAM

Top View (Add-on Card Side)

Bottom View (Add-on Card Side)

Slot Bandwidth

PCIE 3

X16

PCIE 4

X16

HTX3

HTX

PCIE3

PCIE4

HTX3

18

2.5. Expansion Slot

2.5.1 Installing an External Expansion Card to the Riser Card

1. Remove two screws to release the bracket.

2. To install a full length expansion card, please remove two brackets on the side.

3. Insert the full length card into the proper position.

4. Screw the external brackets to fix the card.

①

②

③

④

19

2.5.2 Installing or Replacing HTX_EXTEND CARD and HTX_EXTOLL CARD

HTX_EXTEND CARD

HTX_ EXTOLL CARD

Riser Card Module

Page is loading ...

AIC CB214-OT User manual

AIC CB214-OT User manual

Related papers

Other documents