Crown 137769-3 User manual

Operation Manual

Obtaining Other Language Versions:

To obtain information in another language about the use of this product, please contact your

local Crown Distributor. If you need assistance locating your local distributor, please contact Crown at 574-294-8000.

This manual does not include all of the details of design, production, or variations of the equipment. Nor does it cover every possible

situation which may arise during installation, operation or maintenance.

The information provided in this manual was deemed accurate as of the publication date. However, updates to this information may have

occurred. To obtain the latest version of this manual, please visit the Crown website at www.crownaudio.com.

Trademark Notice:

Crown, Crown Audio, IQ, IQ System, and Amcron are registered trademarks of Crown International. DBC, IQwic

and TCP/IQ are trademarks of Crown International. Other trademarks are the property of their respective owners.

Some models may be exported under the name Amcron.

®

Inc., 1718 W. Mishawaka Rd., Elkhart, Indiana 46517-9439 U.S.A. Telephone: 574-294-8000

DBC Network Bridge

137769-3

2/08

Operation Manual

DBC Network Bridge

page 2

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with a dry cloth.

7) Do not block any ventilation openings. Install

in accordance with the manufacturer’s instruc-

tions.

8) Do not install near any heat sources such as

radiators, heat registers, stoves, or other

apparatus (including amplifiers) that produce

heat.

9) Do not defeat the safety purpose of the polar-

ized or grounding-type plug. A polarized plug

has two blades with one wider than the other.

A grounding-type plug has two blades and a

third grounding prong. The wide blade or the

third prong is provided for your safety. If the

provided plug does not fit into your outlet,

consult an electrician for replacement of the

obsolete outlet.

10) Protect the power cord from being walked on

or pinched, particularly at plugs, convenience

receptacles, and the point where they exit from

the apparatus.

11) Only use attachments/accessories specified

by the manufacturer.

12) Use only with a cart, stand, tripod, bracket, or

table specified by the manufacturer, or sold

with the apparatus. When a cart is used, use

caution when moving the cart/apparatus com-

bination to avoid injury from tip-over.

13) Unplug this apparatus during lightning storms

or when unused for long periods of time.

14) Refer all servicing to qualified service person-

nel. Servicing is required when the apparatus

has been damaged in any way, such as power-

supply cord or plug is damaged, liquid has

been spilled or objects have fallen into the

apparatus, the apparatus has been exposed to

rain or moisture, does not operate normally,

or has been dropped.

15) WARNING: TO REDUCE THE RISK OF FIRE

OR ELECTRIC SHOCK, DO NOT EXPOSE

THIS APPARATUS TO RAIN OR MOISTURE.

16) DO NOT EXPOSE TO DRIPPING OR SPLASH-

ING. DO NOT PLACE OBJECTS FILLED WITH

LIQUID, SUCH AS VASES,ON THIS APPARA-

TUS.

TO PREVENT ELECTRIC SHOCK DO NOT REMOVE

TOP OR BOTTOM COVERS. NO USER SERVICE-

ABLE PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

À PRÉVENIR LE CHOC ÉLECTRIQUE N’ENLEVEZ

PAS LES COUVERCLES. IL N’Y A PAS DES PAR-

TIES SERVICEABLE À L’INTÉRIEUR. TOUS REPA-

RATIONS DOIT ETRE FAIRE PAR PERSONNEL

QUALIFIÉ SEULMENT.

TO COMPLETELY DISCONNECT THIS EQUIPMENT

FROM THE AC MAINS, DISCONNECT THE POWER

SUPPLY CORD PLUG FROM THE AC RECEPTA-

CLE. THE MAINS PLUG OF THE POWER SUPPLY

CORD SHALL REMAIN READILY OPERABLE.

WATCH FOR THESE SYMBOLS:

The lightning bolt triangle is used to alert the user

to the risk of electric shock.

The exclamation point triangle is used to alert the

user to important operating or maintenance instruc-

tions.

Important Safety Instructions

FCC COMPLIANCE NOTICE

This device complies with part 15 of the FCC rules. Operation is subject to the following

two conditions: (1) This device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired

operation.

CAUTION: Changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instruction manual, may cause harmful interference to

radio communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or televi-

sion reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

DBC Network Bridge

Operation Manual page 3

DECLARATION of CONFORMITY

Crown International, Inc.

Sue Whitfield

574-294-8289

[email protected]

European Representative's Name and Address:

Nick Owen

35, Bassets Field

Thornhill

Cardiff. South Glamorgen

CF14 9UG United Kingdom

Equipment Type: Digital B-Chain

Family Name: IQ System Component

Model Names: DBC Network Bridge

EMC Standards:

EN 55103-1:1997 Electromagnetic Compatibility - Product Family Standard for Audio, Video, Audio-Visual and Entertainment Lighting Control Apparatus for Professional Use, Part 1: Emissions

EN 55103-1:1997 Magnetic Field Emissions-Annex A @ 10 cm

EN 61000-3-2:2001 Limits for Harmonic Current Emissions (equipment input current less than or equal to 16 A per phase)

EN 61000-3-3:2002 Limitation of Voltage Fluctuations and Flicker in Low-Voltage Supply Systems Rated Current less than or equal to16A

EN 55022:2003 Limits and Methods of Measurement of Radio Disturbance Characteristics of ITE: Radiated, Class B Limits; Conducted, Class A

EN 55103-2:1997 Electromagnetic Compatibility - Product Family Standard for Audio, Video, Audio-Visual and Entertainment Lighting Control Apparatus for Professional Use, Part 2: Immunity

EN 61000-4-2:2001 Electrostatic Discharge Immunity (Environment E2-Criteria B, 4k V Contact, 8k V Air Discharge)

EN 61000-4-3:2001 Radiated, Radio-Frequency, Electromagnetic Immunity (Environment E2, criteria A)

EN 61000-4-4:2001 Electrical Fast Transient/Burst Immunity (Criteria B)

EN 61000-4-5:2001 Surge Immunity (Criteria B)

EN 61000-4-6:2003 Immunity to Conducted Disturbances Induced by Radio-Frequency Fields (Criteria A)

EN 61000-4-11:2001 Voltage Dips, Short Interruptions and Voltage Variation

Safety Standard:

IEC 60065: 2002 7th Ed. Safety Requirements - Audio Video and Similar Electronic Apparatus

I certify that the product identified above conforms to the requirements of the EMC Council Directive 89/336/EEC as amended by 92/31/EEC, and the Low Voltage Directive 73/23/EES as amended by 93/68/EEC.

Signed

Title: Senior Vice President of Manufacturing

Date of Issue: Dec. 1, 2004

ISSUED BY: Crown International, Inc.

1718 W. Mishawaka Road

Elkhart, Indiana 46517 U.S.A.

Due to line current harmonics, we recommend that you contact your supply authority before connection.

Larry Coburn

FOR COMPLIANCE QUESTIONS ONLY:

Operation Manual

DBC Network Bridge

page 4

1 Getting Started With the DBC Network Bridge

Welcome! This Quick-start guide will get you up and running

in a short time. Then please refer to the rest of the manual for

details on the DBC™ Network Bridge and its operation.

IMPORTANT: Unplug power cord from AC outlet

before wiring.

1.1 Hardware Installation

You will need:

• Crown power amplifiers with USP3-CN PIP modules

installed, or Crown I-Tech CobraNet- version power

amplifiers

• A computer running IQwic software

• A 100Mb network switch

• An Ethernet cable (RJ45 connector on each end) for

use between the computer and network switch

• Two Ethernet cables for use between the DBC Network

Bridge and the network switch. One cable is sufficient,

but two allow redundancy.

• An Ethernet cable between the network switch and

each USP3-CN module (or Ethernet connector)

installed in a Crown power amplifier.

1.1.1 Audio and Network Connections

Please refer to Figures 1.1 and 1.2.

1. Mount the DBC Network Bridge in a standard 19-inch

(48.3-cm) equipment rack or cabinet.

2. Turn off all equipment that will connect to the unit.

3. Connect the AES/EBU digital output signal from your cin-

ema processor, media player, or feature server to the analog

DB25 connector on the back of the DBC Bridge. DB25 wiring

is shown in Table 1 on the next page. Alternatively, connect

the analog output signal from your cinema processor to the

Analog DB25 connector on the back of the DBC Bridge.

DB25 wiring is shown in Table 2 on the next page.

4. See Figure 1.2. Connect any auxiliary mic or line signals

to the female XLR Auxiliary Inputs on the back of the DBC

Network Bridge. Set the MLP switch for Mic, Line, or Phan-

tom-powered mic. Adjust gain potentiometers to optimize

gain structure.

Figure 1.1 System Wiring

  !

! !



$"#.%47/2+

!%3$)')4!,!5$)/

!.!,/'!5$)/

%4(%2.%4

30%!+%2,).%

1

Powe r

2 3 4 5 6 7 8 9 10 1112

234

9101112

5678

13 14 15 16

NETGEAR

$"##ONTROL0#

#4SW)10)0530#.

#4SW)10)0530#.#4SW)10)0530#.#4SW)10)0530#.

%THERNET3WITCH

$"#"RIDGE

$"#)NPUT/PTIONS

$OLBY#0 DTS8$

DTS8$0

!%3!%3

!NALOG

3URROUND#HANNELS

3CREEN#HANNELSAND3UBWOOFERS

Power

Data

Bridge

Fault

Thermal

-20

Signal

12

Ready

Clip

-10

Power

Data

Bridge

Fault

Thermal

-20

Signal

12

Ready

Clip

-10

Power

Data

Bridge

Fault

Thermal

-20

Signal

12

Ready

Clip

-10

Power

Data

Bridge

Fault

Thermal

-20

Signal

12

Ready

Clip

-10

Power

Data

Bridge

Fault

Thermal

-20

Signal

12

Ready

Clip

-10

1

Powe r

2 3 4 5 6 7 8 9 10 1112

234

9101112

5678

13 14 15 16

NETGEAR

Power

Data

Bridge

Fault

Thermal

-20

Signal

12

Ready

Clip

-10

Power

Data

Bridge

Fault

Thermal

-20

Signal

12

Ready

Clip

-10

Power

Data

Bridge

Fault

Thermal

-20

Signal

12

Ready

Clip

-10

Figure 1.2 Audio Inputs on the Back Panel of the DBC Bridge

XLR connector wiring:

pin 1: shield

pin 2: signal hot

pin 3: signal cold

DBC Network Bridge

Operation Manual page 5

Tabl e 1

Tabl e 2

Getting Started With the DBC Network Bridge

13

25

1

14

13

25

1

14

DBC DB25F DIGITAL AES/EBU PINOUTS

DBC DB25F ANALOG PINOUTS

PIN FUNCTION PIN FUNCTION

1 N/C 14 GND

2 N/C 15 AES1 (L/R)–

3 N/C 16 AES3 (Ls/Rs)–

4N/C 17N/C

5 N/C 18 GND

6N/C 19N/C

7 AES1 (L/R)+ 20 N/C

8 AES3 (Ls/Rs)+ 21 AES4 (Bsl/Bsr)–

9 GND 22 AES4 (Bsl/Bsr)+

10 N/C 23 AES2 (C/SW)–

11 GND 24 AES2 (C/SW)+

12 N/C 25 GND

13 N/C

PIN FUNCTION PIN FUNCTION

1 GND 14 L–

2L+ 15GND

3 BSL– 16 BSL+

4 GND 17 C–

5C+ 18GND

6 BSR– 19 BSR+

7 GND 20 R–

8R+ 21N/C

9 GND 22 GND

10 Ls– 23 Ls+

11 Rs– 24 Rs+

12 SW– 25 SW+

13 GND

Operation Manual

DBC Network Bridge

page 6

1.2 Communicating with the DBC Network

Bridge: TCP/IQ™ Networking

1.2.1 The Network Wizard

If you are setting up a dedicated audio network that is not part of

another network, you can use the Network Wizard to set up your

network easily.

1. Open IQwic.

2. Select Setup > Network Wizard.

3. Follow the instructions on the screen.

4. When done, skip to Step 4 on page 11.

1.2.2 Introduction

The DBC Network Bridge connects directly to Crown IQ networks

with TCP/IQ protocol. This permits extensive amp and speaker

diagnostics and control by computer. The DSP functions in the

DBC Network Bridge are controlled and monitored by a computer

running IQwic software.

The computer connects to the DBC Network Bridge on a TCP/IQ

network via a Category 5 cable plugged into the Primary Network

connector on the back of the DBC Network Bridge. The TCP/IQ

format uses off-the-shelf, fast (100 Mb) Ethernet connections.

CobraNet lets you plug in a single cable for both networking and

digital audio -- this is Crown’s Single-Click solution.

Every component in a TCP/IQ network is identified by a unique

address.

1.2.3 TCP/IQ Addressing Rules

In the next section, you will be assigning TCP/IP addresses to

the devices in your network. When you do so, be sure to follow

the addressing rules below. Otherwise, the computer may not

communicate with the devices.

Turn off DHCP (automatic addressing). This will be done in

Instruction 1C, described later.

Assign each device a static (fixed) IP address. An IP address is

made of four numbers separated by periods. Each number can be

zero to 255. The last number can never be a zero or 255. For

example, 126.126.17.1 could be an IP address. 126.126.17.0

would not be a valid IP address.

Make sure that the computer and all the devices have the same

NETWORK IDs in their addresses. This tells the computer that all

those devices are on the same network. Various tools are avail-

able to determine whether devices are on the same network. In

TCP/IQ utility described later, if items are NOT on the same net-

work, they are highlighted in the list.

Make sure that each component has its own TCP/IP address, and

there are no duplicate addresses. The same holds true for IQ

addresses.

Assign a subnet mask. Make it the same for all devices on the

network. If the network you are assembling will interconnect with

other networks, your network is considered to be a subnet within

the larger network. Check with the network administrator to

determine the proper Subnet Mask for your subnet.

If you have a stand-alone network, set the Subnet Mask to

255.255.0.0 for all components, including the computer.

Note: Just because two components have the same subnet mask

does not mean that they are on the same network. As we said, the

subnet mask just tells what part of the TCP/IP address is the Net-

work ID.

Getting Started With the DBC Network Bridge

DBC Network Bridge

Operation Manual page 7

1.2.4 TCP/IQ Setup

This example is based on a stand-alone system using switches and routers. The screen

captures were done in Windows 2000; your exact configuration may vary. If your computer

uses a network for other applications, please check with your Information Technology

Department before making any changes. Section 1.2.5 includes a helpful worksheet for

assigning addresses.

1. Turn on your computer and the rest of the system equipment. On your computer desk-

top, select Start > Settings > Control Panel > Network Connections (Figure 1.3). Set a static

TCP/IP address and Subnet mask on the master computer. Document the address and

mask.

Figure 1.3 Selecting Settings > Control Panel

1A. Right-click on LAN Connections. Then select Internal > Properties (Figure 1.4).

Figure 1.4

Result of Clicking LAN Connections > Internal

Getting Started With the DBC Network Bridge

Operation Manual

DBC Network Bridge

page 8

1B. Once the Properties window opens (Figure 1.5), click on Internet Protocol (TCP/IP).

Figure 1.5 Internal Properties Window

1C. We recommend that you uncheck “Obtain an IP address automatically”, and check

“Use the following address.” If you decide to set an IP address manually, specify an IP

address. The IP address is four numbers between 1 and 255 separated by periods. For

example, 126.126.0.1.

Select a subnet mask. The subnet mask is four numbers between 1 and 255 separated by

periods. For example, 255.255.0.0.

1D. Click OK and close the Control Panel. At this point, some computer operating systems

will require a restart.

Figure 1.6 Internet Protocol (TCP/IP) Properties Window

Getting Started With the DBC Network Bridge

The Internet Protocol (TCP/IQ) Properties window appears (Figure 1.6). Dis-

able Virtual Private Network or other encryption settings.

See Section 1.2.5, TCP/IQ Addressing Worksheet, on the next page. Open

the supplied Excel worksheet called IQ Worksheet.XLS.

255 255 0 0

126 126 0 1

DBC Network Bridge

Operation Manual page 9

EXAMPLE OF AN IQ ADDRESSING WORKSHEET

ADDRESS IQ ADDRESS MODEL DESCRIPTION CHANNEL 1 CHANNEL 2

126.126.0.1 COMPUTER

126.126.0.2 2 I-T8000 #1 RACK ROOM LEFT CLUSTER RIGHT CLUSTER

126.126.0.3

126.126.0.4

126.126.0.5

126.126.0.6

126.126.0.7

126.126.0.8

126.126.0.9

126.126.0.10

126.126.0.11

126.126.0.12

126.126.0.13

126.126.0.14

126.126.0.15

126.126.0.16

126.126.0.17

126.126.0.18

126.126.0.19

126.126.0.20

Getting Started With the DBC Network Bridge

1.2.5 TCP/IQ Addressing Worksheet

Table 3 is an example of valid TCP/IP addresses on a stand-alone network. If the TCP/IQ

network is going to be shared with other people, check with the Network Administrator for

their addressing scheme. Without getting into all of the networking rules, the table lists

approximately 20 network addresses out of a possible 65,534 addresses on this network.

There are other addresses that are valid; these are just shown as a starting point.

• The Subnet Mask for all components, including the computer, needs to be set to

255.255.0.0.

• Each computer running IQwic software must have a subnet mask of 255.255.0.0. It also

must be assigned one of the addresses listed on the following table.

• A space has been left to the right of all the addresses. This area is for your notes, such as

the IQ address or the component type.

In the CD-ROM that came with your DBC Network Bridge is an Excel spreadsheet that you

can use to keep track of TCP/IQ addresses.

Table 3

Operation Manual

DBC Network Bridge

page 10

2. Select IQ Systems > IQwic > TCPIQ Utility (Figure 1.7). This launches the TCPIQ Utility

on the master computer.

Figure 1.7 Selecting IQ Systems > IQwic > TCPIQ Utility

2A. The master computer should discover the TCP/IQ products (Figure 1.8). If not, please

re-read Section 1.2.4 on addressing rules. Also read Chapter 6, Troubleshooting.

Figure 1.8 Example of Discovered Components

2B. Once TCP/IQ Utility has launched, select a single component and click on Set

Address. In the Set Address window (Figure 1.9), set up a TCP/IQ address—it must be

unique. Then set up the same Subnet mask for all of the components as well as the master

computer. Set the IQ address, and select Send Code.

2C. Close the software. Repeat as necessary.

Figure 1.9 Set Address Window

3. Launch the IQwic program. (Figure 1.10).

Figure 1.10 Selecting IQ Systems > IQwic

Getting Started With the DBC Network Bridge

DBC Network Bridge

Operation Manual page 11

4. The Component Discovery screen appears and displays the mes-

sage, “Searching for TCP/IQ components” (Figure 1.11).

Getting Started With the DBC Network Bridge

5. The IQwic toolbar and Workspace appear. An icon of the DBC Net-

work Bridge appears in the Workspace (Figure 1.12)

6. Double-click the DBC Network Bridge Icon. The Input-Output

window appears (Figure 1.13).

7. Click on the yellow Expand/Shrink bar at

the bottom of the Input-Output window.

Figure 1.12 The IQwic Toolbar (Top)

and Workspace (Bottom)

Figure 1.13 The

Input-Output

Window

Figure 1.11 The Discovery Screen

Operation Manual

DBC Network Bridge

page 12

If there are problems, please re-read Section 1.2.3 on

addressing rules. Also read Chapter 6, Troubleshooting.

8. The processing functions appear. Click on the Unit

Presets tab at the top. The Unit Presets window appears

(Figure 1.14).

9. At the bottom right, select Preset 32, Standard Cinema.

Then select Recall this Preset. Your system is running

and ready to configure. Please continue reading the man-

ual.

Figure 1.14 The Unit Presets Window

Getting Started With the DBC Network Bridge

DBC Network Bridge

Operation Manual page 13

Important Safety Instructions ........................................................... 2

Declaration of Conformity................................................................. 3

1 Getting Started with the DBC Network Bridge .................... 4

1.1 Hardware Installation............................................................ 4

1.1.1 Audio and Network Connections.................................. 4

1.2 Communicating with the DBC Network Bridge...................... 6

1.2.1 The Network Wizard..................................................... 6

1.2.2 Introduction ................................................................. 6

1.2.3 TCP/IQ Addressing Rules ............................................ 6

1.2.4 TCP/IQ Setup............................................................... 7

1.2.5 TCP/IQ Addressing Worksheet..................................... 9

Table of Contents.............................................................................. 13

2 Welcome ....................................................... 14

2.1 Features ............................................................................... 14

2.2 How to Use This Manual....................................................... 14

Sample Application Diagram ............................................................ 15

3 Setup ............................................................ 16

3.1 Unpack and Install Your DBC Network Bridge ..................... 16

3.2 Connecting to AC Mains ...................................................... 16

3.3 Wiring................................................................................... 17

3.3.1 Analog, Digital and Auxiliary Inputs............................. 17

3.3.2 Balanced Input Wiring ................................................. 18

3.3.3 Unbalanced Input Wiring ............................................. 18

3.3.4 Balanced Monitor Output Wiring ................................. 18

3.3.5 Unbalanced Monitor Output Wiring .............................19

3.3.6 CobraNet Connections.................................................19

3.3.7 Control Port Connections ............................................19

4 Operation ....................................................... 20

4.1 Front Panel Controls and Indicators......................................20

4.2 Back Panel Controls and Connectors ...................................21

4.3 Navigating the LCD Control Screen ......................................22

4.3.1 Functions, Controls and Screens................................. 22

4.3.2 Operation Examples..................................................... 23

4.3.3 Menu Tree....................................................................23

4.4 IQwic Overview ....................................................................24

4.5 Metering ...............................................................................25

4.6 General Tab...........................................................................26

4.7 Basic Processing Functions..................................................27

4.7.1 Signal Path Tab, Cinema Surround Form..................... 27

4.7.2 Input Compressor........................................................28

4.7.3 Input Delay................................................................... 29

4.7.4 EQ Filters ....................................................................30

4.7.5 All Outputs Volume Controls .......................................32

4.7.6 Signal Generator..........................................................33

4.7.7 CobraNet: Explanation .................................................34

4.7.8 Cobranet: Output..........................................................35

4.7.9 Booth Monitor Source Select.......................................36

4.7.10 Presets.......................................................................37

4.7.11 Preset Editor ..............................................................38

Table of Contents

4.7.12 Scenes........................................................................39

4.7.13 Scene Editor...............................................................40

4.7.14 Events Scheduler........................................................41

4.8 General Firmware Features....................................................43

4.8.1 Input Level Meters........................................................43

4.8.2 Input Dynamic Cut/Boost Meters..................................43

4.8.3 Output Level Meters .....................................................43

4.8.4 Output Dynamic Cut/Boost Meters...............................43

4.8.5 Memory Backup ...........................................................43

4.8.6 Presets .........................................................................43

4.8.7 Real Time Clock ...........................................................43

4.8.8 Events...........................................................................43

5 Advanced Operation ........................................... 44

5.1 Advanced Operation Table of Contents ..................................44

5.2 Advanced Functions..............................................................45

5.3 Advanced Form Firmware Features........................................54

5.4 Technical Description ............................................................69

6 Troubleshooting ................................................ 70

7 Specifications .................................................. 73

8 Appendix A: TCP/IQ Network Basics......................... 75

9 Service........................................................... 80

10 Warranty ....................................................... 81

Crown Audio Factory Service Information Form ............83

Operation Manual

DBC Network Bridge

page 14

2 Welcome

At the heart of a Digital B Chain system, the

Crown

®

DBC Network Bridge allows you to

distribute multiple channels of digital audio

over standard fast Ethernet hardware and

cabling for use in traditional, e-cinema and d-

cinema applications.

The DBC Bridge accepts standard analog and/

or AES digital audio and CobraNet

®

digital

channels from other Cinema processors

(Dolby

®

, DTS

®

), Cinema Servers, or Alterna-

tive Content Media Players; and bridges

(routes) them to a Crown DBC network. Figure

2.1 is a sample application drawing.

This network is Crown’s proprietary “Single-

Click” solution that provides system control,

monitoring, diagnostics, and digital audio

transport. The DBC network (fed by the DBC

Network Bridge) distributes the digital audio

and system-wide control protocol to Crown

amplifiers. The DBC Network Bridge also pro-

vides the necessary system equalization, which

is stored and recalled via a series of presets for

use in both feature film and alternative content

programming.

2.1 Features

• Accepts 8 inputs (7.1 surround) via one of

the following formats:

Analog

AES/EBU

CobraNet

• Selectable mic, mic with 24V phantom

power, or line analog XLR inputs for alternative

content

• Primary and Secondary 100 Mb Ethernet

“Single-Click” connection for DBC network

• Front-panel LCD display and control func-

tions of internal presets and system setup

• Full 32-channel CobraNet digital audio

transmit/receive capability

• Enhanced matrix mixer capable of full 8x32

crosspoint matrix mixing

• 24-bit/48 kHz converters

• Studio-grade DSP with multiple filter banks

for each channel (up to 256 filters)

• 32 presets, 32 scenes, and 32 events can be

stored, labeled, and recalled

• Analog monitoring of cinema processor

inputs, pre-amp, or post-amp signals

• Multiple-function control port for third-party

automation/control

• Internal clock/calendar for scheduling events

• Auto-leveling functions for dynamic volume

control of auditoriums or lobby

• Ambient-leveling functions for maintaining

maximum signal-to-noise ratio

• Three-year, no-fault, fully transferable war-

ranty

2.2 How to Use This Manual

This manual provides you with the necessary

information to safely and correctly setup and

operate your DBC Network Bridge. It does not

cover every aspect of installation, setup or

operation that might occur under every condi-

tion. For additional information, please consult

Crown’s DBC Bridge Application Guide (avail-

able online at www.crownaudio.com), Crown

Technical Support, your system installer or

retailer.

We strongly recommend you read all instruc-

tions, warnings and cautions contained in this

manual. Also, for your protection, please send

in your warranty registration card today. And

save your bill of sale — it’s your official proof

of purchase.

DBC Network Bridge

Operation Manual page 15

  !

! !



$"#.%47/2+

!%3$)')4!,!5$)/

!.!,/'!5$)/

%4(%2.%4

30%!+%2,).%

1

Powe r

23456789101112

234

9101112

5678

13 14 15 16

NETGEAR

$"##ONTROL0#

#4SW)10)0530#.

#4SW)10)0530#.#4SW)10)0530#.#4SW)10)0530#.

%THERNET3WITCH

$"#"RIDGE

$"#)NPUT/PTIONS

$OLBY#0 DTS8$

DTS8$0

!%3!%3

!NALOG

3URROUND#HANNELS

3CREEN#HANNELSAND3UBWOOFERS

Power

Data

Bridge

Fault

Thermal

-20

Signal

12

Ready

Clip

-10

Power

Data

Bridge

Fault

Thermal

-20

Signal

12

Ready

Clip

-10

Power

Data

Bridge

Fault

Thermal

-20

Signal

12

Ready

Clip

-10

Power

Data

Bridge

Fault

Thermal

-20

Signal

12

Ready

Clip

-10

Power

Data

Bridge

Fault

Thermal

-20

Signal

12

Ready

Clip

-10

1

Powe r

2 3 4 5 6 7 8 9 10 1112

234

9101112

5678

13 14 15 16

NETGEAR

Power

Data

Bridge

Fault

Thermal

-20

Signal

12

Ready

Clip

-10

Power

Data

Bridge

Fault

Thermal

-20

Signal

12

Ready

Clip

-10

Power

Data

Bridge

Fault

Thermal

-20

Signal

12

Ready

Clip

-10

Figure 2.1 Sample Application: Large Cinema System Diagram

Operation Manual

DBC Network Bridge

page 16

3.1 Unpack and Install Your

DBC Network Bridge

Please unpack and inspect your product for any

damage that may have occurred during transit.

If damage is found, notify the transportation

company immediately. Only you can initiate a

claim for shipping damage. Crown will be

happy to help as needed. Save the shipping

carton as evidence of damage for the shipper’s

inspection.

We also recommend that you save all packing

materials so you will have them if you ever

need to transport the unit. Never ship the

unit without the factory pack.

YOU WILL NEED (not supplied):

• Input wiring cables

• Network cables

• Rack for mounting the DBC Network

Bridge (or a stable surface for stacking)

WARNING: Before you start to set up

your DBC Network Bridge, make sure

you read and observe the Important

Safety Instructions found at the begin-

ning of this manual.

CAUTION: Before you begin, make sure

your DBC Network Bridge is discon-

nected from the power source.

Use a standard 19-inch (48.3 cm) equipment

rack (EIA RS-310B). See Figure 3.1 for dimen-

sions.

You may also stack units without using a

cabinet.

NOTE: When transporting, units should be sup-

ported at both front and back.

3.2 Connecting to AC Mains

WARNING: The third (ground) prong of

the AC power cord connector is a

required safety feature. Do not attempt

to disable this ground connection by

using an adapter or other methods.

3 Setup

Figure 3.1 Dimensions

DBC Network Bridge

Operation Manual page 17

3.3 Wiring

Chapter 1 describes how to make connections to the DBC Network Bridge.

The information below describes the connections in detail.

3.3.1 Analog, Digital and Auxiliary Inputs

Analog Line Input: DB25 female connector accepts eight balanced ana-

log line-level analog inputs. Pinout matches Dolby CP-650 analog output.

See Table 2 on page 5.

Digital Audio Input: DB25 female connector accepts eight AES3 digital

audio signals. Pinout matches Dolby #778 AES input/output card for CP-

650. See Table 1 on page 5.

Auxiliary Inputs: Two female XLR balanced inputs for speech reinforce-

ment or announcements (see Figure 3.2).

Each input has an input selector switch.

• Slide it to the left (M) for microphone signal levels up to +7dBu

(0dBu = 0.775 volts).

• Select the center position (L) for line-level signals up to +20

dBu.

• Slide it to the right (P) to provide 24VDC to mics requiring

phantom power.

Each input has a screwdriver-set, calibrated gain control to compensate for

different input source levels. The slot on the control shaft points to the gain

setting. The settings are labeled for line-level input. Add 25 dB to the scale

if the inputs are switched for microphone level signals.

Use a screwdriver to adjust the gain pot so that the input signal level plus

gain equals roughly 0dBu. You will need to know, or estimate, the level of

the input source. Setting the source signal level to approximately 0dBu will

provide 20dBu of headroom in the input preamp. Some recommended set-

tings are given in Table 4.

3 Setup

Figure 3.2 Aux Input Level Controls, XLR connectors and

Mic/Line/Phantom Slide Switch

Pro Audio Equip-

ment

Semi-Pro or con-

sumer equipment

Dynamic mic,

speech

Condenser mic,

speech

Hot condenser

mic, speech

dBm/dBV

(nominal)

+4 dBm –10 dBV –75 dBV –65 dBV –45 dBV

dBu (nominal) +4 dBu –8 dBu –73 dBu –63 dBu –43 dBu

Suggested Setting –4 (L) +8 (L) +20 (M) +18 (P) +11 (P)

Table 4. Suggested Audio Input Gain Control Settings

0 dBm = 0.775 Vrms with a 600-ohm load.

0 dBV = 1 Vrms.

0 dBu = 0.775 Vrms.

Operation Manual

DBC Network Bridge

page 18

3.3.2 Balanced Input Wiring

Balanced sources should be wired as shown below. Notice that the

shield is not connected to the chassis ground of the source if the

source is also connected to the AC ground (that is, it has a grounded

AC plug). This prevents unwanted ground loops.

3.3.3 Unbalanced Input Wiring

Unbalanced sources should be wired as shown below. The examples are grouped

according to whether you use twin-lead shielded wire or single-lead coax (or

twisted pair).

3.3.4 Balanced Monitor Output Wiring

Balanced Monitor Output wiring is shown in Figures 3.5. Notice

that if the load is connected to AC ground, the shield should not

be connected to the output ground terminal. This will prevent

unwanted ground loops.

1. Assemble a 2-conductor shielded cable with a Phoenix-type 3-

terminal connector on one end. On the other end, solder a con-

nector that mates with your booth monitor amplifier/speaker.

2. Plug the Phoenix-type connector into the Monitor Output con-

nector on the back of the DBC Network Bridge.

3. Plug the other end of the cable into your booth monitor ampli-

fier/speaker.

12

3

2

3

1

12

3

12

3

3 Setup

12

3

12

3

12

3

12

3

Figure 3.3 Balanced Audio Input Wiring

Figure 3.4 Unbalanced Audio Input Wiring

Figure 3.5 Balanced Monitor Output Connections

+

S

–

+

–

TO MONITOR AMP/SPEAKER

DBC Network Bridge

Operation Manual page 19

3.3.5 Unbalanced Monitor Output Wiring

3 Setup

Figure 3.6 Unbalanced Monitor Output Connections

3.3.6 CobraNet Connections

The CobraNet network carries up to 32 channels of audio bidirectionally

via a single cable. Connect the DBC Network Bridge to the CobraNet net-

work using RJ45-terminated standard CAT 5 cable from the PRIMARY con-

nector on the rear of the unit.

The PRIMARY connection can either be connected to another DBC Network

Bridge unit or other CobraNet-compatible component’s PRIMARY port. A

further option is to connect to a port on a 100Mbit Ethernet switch or hub

in order to distribute the network audio to other devices. Devices that are to

communicate with the DBC Network Bridge will all need unique Ethernet IP

addresses assigned. See the CobraNet sections 4.7.8 and 8.3 for more

details.

The SECONDARY connector is for creating a redundant network for backup

purposes. This port should be tied to the backup Ethernet network. In the

event of a failure in the cabling or hardware connected to the PRIMARY

system the DBC Network Bridge will switch to the SECONDARY network in

a matter of seconds.

On each connector are two LEDs. The left LED (IN USE/CONDUCTOR)

lights yellow when the port is in use and will blink if the device is also the

conductor (the CobraNet timing master). The right LED (LINK/ACTIVITY)

lights green when link is established and blinks when network activity is

detected. Both LEDs flash yellow in unison to report a fatal error. The Sec-

ondary Connector has identical LEDs as the Primary Connector.

3.3.7 Control Port Connections

Connect any external circuits you plan to use to control and/or monitor the

DBC Network Bridge via the Control Port. Figure 3.7 shows pin assign-

ments for the Control Port. See the Control Port (Section 5.2.4) for infor-

mation on the operation of the Control Port, and for examples of wiring

circuits to the Control Port connector.

DBC Network Bridge Control Port (DB37)

Pins 1 through 8 are assignable to manually select a binary (on/off) value,

chosen Preset status, or status of any logical binary control or sensor

(most likely gate and Preset).

Pins 20 through 27 provide an analog output from 0 to +10VDC that is

assignable or can reflect an object (including faders) of the unit.

A total of 1 amp of current is available from all outputs.

Pins 12 through 19 are assignable to logic Preset recall and general con-

trol for logical type objects within the unit, and are assignable to any com-

bination of mute controls. Pins 30 through 37 function as analog inputs

and are assignable to any combination of fader controls.

Figure 3.7 Control Port Pin Assignment

Operation Manual

DBC Network Bridge

page 20

4 Operation

4.1 Front Panel Controls

and Indicators

A. LCD Display

LCD digital display shows information about the

currently selected IQ address, inputs, presets,

scenes, and firmware information.

B. Input Display

An eight-segment LED display matrix shows input

signal presence for all eight analog or digital inputs.

C. Power Indicator

Blue LED shows that the unit is plugged in and AC

power is being supplied. The unit does not have a

power on/off switch.

D. Menu/Select Button

Scrolls through the menus of IQ address, inputs,

presets, scenes, and firmware information. Also

used to select a parameter that is found by the Next/

Prev buttons.

E., F. Next/Previous Buttons

These two buttons scroll through parameters in

each menu.

G. Output display

An eight-segment LED display matrix shows output

signals for all eight surround channels.

H. Data Indicator

Amber LED flashes when commands addressed to

the DBC Bridge are received.

I. AES/EBU Indicator

Amber LED illuminates when the unit is switched to

AES digital inputs.

Figure 4.1 Front Panel Controls and Indicators

Page is loading ...

Crown 137769-3 User manual

This manual is also suitable for

Crown 137769-3 User manual

Related papers

Other documents