Model number: SMC7901WBR2- B1
Topic: Wireless Encryption (WPA)
Configuration – Configure the Wireless Encryption setting through the router’s admin web via
Internet Explorer (IE)
It is highly recommended to configure the Wireless Encryption by wired connection.
a. Access into the admin page (http://192.168.2.1/).
b. Key in the Username & password to login; default username: admin; default password:
smcadmin.
c. Click WLAN Security. Choose WPA2 Mixed under Encryption. Enter a password in the Pre-
Shared Key and click Apply Changes.
SMC7901WBRA2-B1 Installation Guide
d. Scroll up and click on Commit/Reboot.
e. Make sure “commit current settings” is checked and click on Reboot.
f. After reboot is done, Security is up.
Topic: Wireless Encryption (WEP)
Configuration – Configure the Wireless Encryption setting through the router’s admin web via
Internet Explorer (IE)
It is highly recommended to configure the Wireless Encryption by wired connection.
a. Access into the admin page (http://192.168.2.1/).
b. Key in the Username & password to login; default username: admin; default password:
smcadmin.
c. Click WLAN Security. Choose WEP under Encryption. Click on Set WEP Key to create a
password.
d. A small window will popup from here. Make sure Key Length is under 64-bit and Key Format is
under Hex(10 characthers). Create a Password Key under Encryption Key 1. Click on Apply
Changes.
Note: Default Tx Key must be on Key 1 and Password Key only needs to be entered in
Encryption Key 1.
e. Scroll up and click on “Commit Reboot”.
f. Make sure “commit current settings” is checked and click on Reboot.
f. After reboot is done, Security is up.
Topic: Port forwarding(Virtual Server)
Configuration – Configure the Wireless Encryption setting through the router’s admin web via
Internet Explorer (IE)
It is highly recommended to configure the Wireless Encryption by wired connection.
a. Access into the admin page (http://192.168.2.1/).
b. Key in the Username & password to login; default username: admin; default password:
smcadmin.
c. Click Advanced Virtual Server Services. Click on Add.
Topic: MAC Filter
Configuration – Configure the Wireless Encryption setting through the router’s admin web via
Internet Explorer (IE)
It is highly recommended to configure the Wireless Encryption by wired connection.
a. Access into the admin page (http://192.168.2.1/).
b. Key in the Username & password to login; default username: admin; default password:
smcadmin.
c. Click Advanced Firewall MAC Filter. Click on Add Rule.
d. Enter the MAC address you wants to filter in the Src MAC Address as shown below and click
on Add. Do the same for Incoming.
e. Scroll up and click on “Commit Reboot”.
f. Make sure “commit current settings” is checked and click on Reboot.
f. After reboot, MAC address entered will not be able to surf net.
d. Enter port of the application/device you wants to open and the IP address of the device/PC
using the application as show below.
e. click on “Commit Reboot”.
f. Make sure “commit current settings” is checked and click on Reboot.
f. After reboot, IP address entered will not be able to surf net.
Topic: URL Blocking
Configuration – Configure the Wireless Encryption setting through the router’s admin web via
Internet Explorer (IE)
It is highly recommended to configure the Wireless Encryption by wired connection.
a. Access into the admin page (http://192.168.2.1/).
b. Key in the Username & password to login; default username: admin; default password:
smcadmin.
c. Click Advanced Firewall URL Blocking. Check on Enabled under URL Blocking and click
on Apply Changes.
For blocking Website link: Enter the website address under the Domain Name and click on Add
Domain Name.
For blocking Keyword: Enter the characters under the Keyword and click on Add Keyword.
Note: Blocking keyword will deny any access to website address with the keyword entered.
d. click on “Commit Reboot”.
Topic: Remote Management
Configuration – Configure the Wireless Encryption setting through the router’s admin web via
Internet Explorer (IE)
It is highly recommended to configure the Wireless Encryption by wired connection.
a. Access into the admin page (http://192.168.2.1/).
b. Key in the Username & password to login; default username: admin; default password:
smcadmin.
c. Click Admin Remote Access. Check on HTTP as shown below and click on Apply Changes.
d. Go to Commit/Reboot and check on commit current settings. Click on Reboot.
e. After reboot. You will be able to access to this router via WAN IP outside the network.
Topic: PPPoE Setup
Configuration – Configure the Wireless Encryption setting through the router’s admin web via
Internet Explorer (IE)
It is highly recommended to configure the Wireless Encryption by wired connection.
a. Access into the admin page (http://192.168.2.1/).
b. Key in the Username & password to login; default username: admin; default password:
smcadmin.
c. Click WAN WAN interface. Enter VPI/VCI (Singapore:0/100) and PPPoE for Channel Mode.
Enter your ADSL account and password. Click on Add.
d. Scroll up and click on Commit/Reboot.
Topic: IP/Port Filter
Configuration – Configure the Wireless Encryption setting through the router’s admin web via
Internet Explorer (IE)
It is highly recommended to configure the Wireless Encryption by wired connection.
a. Access into the admin page (http://192.168.2.1/).
b. Key in the Username & password to login; default username: admin; default password:
smcadmin.
c. Click Advanced Firewall IP/Port Filter. Click on Add Rule.
d. Enter the IP address you wants to filter in the Src IP Address as shown below and the port to
be denied for access and click on Add. Do the same for Incoming.
e. Scroll up and click on “Commit Reboot”.
f. Make sure “commit current settings” is checked and click on Reboot.
f. After reboot, IP address entered will not be able to surf net.
Topic: Firmware Upgrade
Configuration – Configure the Wireless Encryption setting through the router’s admin web via
Internet Explorer (IE)
It is highly recommended to configure the Wireless Encryption by wired connection.
a. Access into the admin page (http://192.168.2.1/).
b. Key in the Username & password to login; default username: admin; default password:
smcadmin.
c. Click Admin Upgrade Firmware. Click on Browse and select the firmware file. Click on
Upload.
d. Go to Commit/Reboot and check on commit current settings. Click on Reboot.
Topic: DMZ
Configuration – Configure the Wireless Encryption setting through the router’s admin web via
Internet Explorer (IE)
It is highly recommended to configure the Wireless Encryption by wired connection.
a. Access into the admin page (http://192.168.2.1/).
b. Key in the Username & password to login; default username: admin; default password:
smcadmin.
c. Click Advanced Virtual Server DMZ Settings. Check on Enable DMZ and enter the IP of
the PC hosted. Click on Apply changes.
d. click on “Commit Reboot”.
Page is loading ...
/
