Page is loading ...
B349902202WY0
3
9902202WY
STOP
1-800-489-3351
Need Parts or Assistance?
WWW.AMERIWOOD.COM/PARTS
If a part is missing or damaged, visit our website or call our toll-free
customer service line. We will gladly ship your replacement parts
FREE of charge.
For prompt, reliable service please have your assembly manual ready.
DO
NOT
RETURN PRODUCT TO THE STORE
Individual stores do not stock parts.
or call toll free:
Recommended # of people needed for assembly: 1
(however it is always better to have an extra hand.)
Estimated assembly time is 1 hour.
Spanish translations are located in the center of this manual.
Se localizan las traducciones españolas en el centro de este
manual.
THIS INSTRUCTION BOOKLET CONTAINS
IMPORTANT SAFETY INFORMATION. PLEASE
READ AND KEEP FOR FUTURE REFERENCE.
Date of Purchase
___ / ___ / ___
0 29986 9902
1 1
A Dorel Company
MERIWOOD
INDUSTRIES
TM
B349902202WY0
3
3 /16
Parts
left hutch panel
39118202050
right hutch panel
39118202060
2 hutch dividers
39118202070
center hutch divider
39118202080
2hutch backs
39118202091
hutch top
39902202120
hutch fixed shelf
39118202131
left upper
crown molding
39118202240
right upper
crown molding
39118202250
2 vertical hutch moldings
39118202260
horizontal hutch molding
39118202270
upper back panel
K911820210
AA
Z
Y
X
M
L
I
H
G
F
E
TT
front crown molding
39118202210
U
B349902202WY03
4 /16
Hardware
cam lock
#A22430
Qty: 15
nail
#A21110
Qty: 25
1/2" pan head
screw
#A12210
Qty: 30
angle bracket
#A53600
Qty: 15
compression dowel
#A21520
Qty: 3
1" washer head
screw
#A12840
Qty: 4
1
2
3
4
5
cam bolt
#A22440
Qty: 15
6
7
#8 x 1-3/4" flat
head screw
#A13410
Qty: 14
8
A21110 (X25)
nail
A22430 (X15)
cam lock
A21520 (X3)
compression
dowel
A12840 (X4)
1" washer head
screw
A22440 (X15)
cam bolt
A13410 (X14)
#8 x 1-3/4" flat
head screw
A12210 (X15)
1/2" pan head
screw
A12210 (X15)
1/2" pan head
screw
A53600 (X8)
angle bracket
A53600 (X7)
angle bracket
6
1
4
2
5
7
8
3
3
2
HARDWARE COMPARTMENT
LAYOUT
2
½ turn to fully
lock.
½ se vuelven a
totalmente
cerradura.
1
43
This illustration shows how the CAM fastening system works.
Esta ilustración muestra el sistema de fijación de leva y como funciona.
Proper orientation of cam.
La orientación apropiada de leva.
Lock
Apretar
Tighten to fully seat. Do not over
tighten.
Apriétese a totalmente asiento. No
haga encima de apriétese.
1
B349902202WY0
3
5 /16
x 2
x 2
Insert two CAM LOCKS (6) into both of the HUTCH BACKS (I) as shown.
Insert one CAM LOCK (6) and tap one COMPRESSION DOWEL (4) into the HUTCH DIVIDERS (G and H).
4
6
x 7
x 3
Proper orientation of CAM LOCK
Posición correcta de la cerradura de leva
Approx.
7/16"
4
6
G
H
I
2
B349902202WY0
3
6 /16
Insert four CAM LOCKS (6) into the HUTCH FIXED SHELF (M) as shown.
Attach the HORIZONTAL HUTCH MOLDING (AA) to the HUTCH FIXED SHELF (M) with four ANGLE BRACKETS (3) and eight
SCREWS (2). Molding (AA) is centered on Shelf (M) as shown below.
Proper orientation of CAM LOCK
Posición correcta de la cerradura de leva
x 4
3
2
6
x 4
x 8
ASSEMBLED VIEW
VISTA DEL ENSAMBLAJE
2
2
3
6
6
M
AA
AA
M
AA
M
35 (1-3/8")
35 (1-3/8")
3
B349902202WY0
3
7 /16
2
3
6
7
x 6
x 3
x 2
x 2
E
Z
Proper orientation of CAM LOCK
Posición correcta de la cerradura de leva
Insert two CAM LOCKS (6) and screw two CAM BOLTS (7) into the LEFT HUTCH PANEL (E) as shown.
Attach the VERTICAL HUTCH MOLDING (Z) to the LEFT HUTCH PANEL (E) with three ANGLE BRACKETS (3) and six
SCREWS (2). Do not tighten the angle bracket screws. Tighten these screws in later steps after adjustments are made.
ASSEMBLED VIEW
VISTA DEL ENSAMBLAJE
flush at this end
alinee en el final
6
7
2
2
3
Z
E
4
B349902202WY0
3
8 /16
2
3
7
6
x 6
x 3
x 2
x 2
F
Z
Insert two CAM LOCKS (6) and screw two CAM BOLTS (7) into the RIGHT HUTCH PANEL (F) as shown.
Attach the VERTICAL HUTCH MOLDING (Z) to the RIGHT HUTCH PANEL (F) with three ANGLE BRACKETS (3) and six
SCREWS (2). Do not tighten the angle bracket screws. Tighten these screws in later steps after adjustments are made.
Proper orientation of CAM LOCK
Posición correcta de la cerradura de leva
7
6
3
2
2
Flush at this end.
Alinee en el final.
Z
F
ASSEMBLED VIEW
VISTA DEL ENSAMBLAJE
5
B349902202WY0
3
9 /16
3
7
2
7
x 10
x 5
x 11
3
2
2
U
L
Screw eleven CAM BOLTS (7) into the HUTCH TOP (L).
Attach the FRONT CROWN MOLDING (U) to the HUTCH TOP (L) with five ANGLE BRACKETS (3) and ten SCREWS (2).
DO NOT TIGHTEN UNTIL STEP 9
NO AJUSTE HASTA LLEGAR AL PASO 9
6
B349902202WY0
3
10 /16
L
I
I
G
G
H
U
UNLOCK
LOCK
APRETAR
DESAPRETAR
6
7
Align the HUTCH DIVIDERS (G and H) with the HUTCH TOP (L) so that
the CAM BOLTS (7) insert into the CAM LOCKS (6).
Turn the CAM LOCKS (6) clockwise to lock in place.
Align the HUTCH BACKS (I) with the HUTCH TOP (L) so that the CAM
BOLTS (7) insert into the CAM LOCKS (6).
Turn the CAM LOCKS (6) clockwise to lock in place.
7
B349902202WY0
3
11 /16
UNLOCK
LOCK
APRETAR
DESAPRETAR
E
F
M
AA
6
7
Align the HUTCH PANELS (E and F) with the HUTCH FIXED SHELF (M) so that the CAM BOLTS (7) insert
into the CAM LOCKS (6).
Turn the CAM LOCKS (6) clockwise to lock in place.
8
B349902202WY0
3
12 /16
8
8
UNLOCK
LOCK
APRETAR
DESAPRETAR
With assistance of another person align the HUTCH PANELS (E and F) with the HUTCH TOP (L) so that the CAM BOLTS (7)
insert into the CAM LOCKS (6).
Turn the CAM LOCKS (6) clockwise to lock in place.
Secure the HUTCH FIXED SHELF (M) to the HUTCH DIVIDERS (G and H) and the HUTCH BACKS (I) with ten SCREWS (8).
7
6
L
U
F
E
M
I
I
G
G
H
x 10
5
x 4
X
Y
5
5
Attach the LEFT UPPER CROWN MOLDING (X) to the LEFT HUTCH PANEL (E) with two SCREWS (5).
Attach the RIGHT UPPER CROWN MOLDING (Y) to the RIGHT HUTCH PANEL (F) with two SCREWS (5).
Adjust the moldings by loosening the screws, adjust the moldings, and retightening the screws.
9
B349902202WY0
3
13 /16
8
x 4
K
E
F
8
NOTE: You need to use a 3/16" diameter drill
bit and make the four holes depicted below
into through holes.
With assistance of another person carefully turn
the unit over onto it's rear surface.
Attach the DESK TOP (K) from the DESK (model
9151202W) to the HUTCH PANELS (E and F) with four
SCREWS (8).
With assistance of another person, carefully turn the unit over
onto the finished edges. Position the UPPER BACK PANEL
(TT) as shown. One person needs to hold up the bottom edge
of the back panel while another person adjusts the fit and nails
it to the unit. Flush the top edge of the BACK PANEL (TT) with
the top edge of the HUTCH FIXED SHELF (M) and align
squarely with the outer edges of the LEFT HUTCH PANEL (E)
and RIGHT HUTCH PANEL (F).
The hutch panels (E) and (F) must be square with the back
panel when nailing. Align Squarely and nail straight
through into the back edges.
TT
TT
F
E
1
x 20
1
RAW SURFACE
SUPERFICIE CRUDA
top edge of Hutch Fixed Shelf (M)
10
B349902202WY0
3
14 /16
UNLOCK
LOCK
APRETAR
DESAPRETAR
The hutch is now ready to attach to the desk. Assemble the desk up to this point of assembly (step 10 of the
desk assembly).
With assistance of another person, carefully position the hutch and desk as shown.
Align the left and right assemblies with the DESK TOP (K) so that the CAM BOLTS (7) insert into the CAM LOCKS (6).
Turn the CAM LOCKS (6) clockwise to lock in place.
A
B
C
D
J
K
7
6
11
B349902202WY0
3
15 /16
With assistance of another person, carefully stand the unit upright. Attach the LEFT LOWER BACK (RR) and RIGHT LOWER
BACK (SS) using the thirty-six nails (16) from the desk (9151202W) hardware bag. Use five nails (1) to fasten the Hutch Back
Panel to the rear edge of the Desk Top (K).
The desk panels must be square with the back panels when nailing.
RAW SURFACE
SUPERFICIE CRUDA
TT
E
F
K
M
After completing this assembly
step, go to step 12 of the desk
(model 9151202W) assembly
instructions for completing the
desk assembly.
RAW SURFACE
SUPERFICIE CRUDA
RAW SURFACE
SUPERFICIE CRUDA
16
16
16
x 36
RR
SS
A
D
B
C
O
P
product collapse, and/or serious injury.
tightened firmly. Failure to do so could cause instability,
All nails must be driven into the parts straight, centered and
Please make sure that the Back Panel is attached securely.
WARNING
Por favor asegúrese que las Parte de atrás se atan
firmemente. Todos los clavos deben manejarse en las
partes recto y deben apretarse firmemente. El fracaso para
hacer para que podría causar inestabilidad, derrumbamiento
del producto, y/o la lesión seria.
ADVERTENCIA
1
x 5
1
Flush the edge of the back panels with the bottom edge of the
bottom shelves. Align squarely and nail straight through into
the back panels.
B349902202WY0
3
16 /16
Visit our Website or call our toll free number for any assistance you should
need:
Clean the product with your favorite furniture polish and a soft cloth. DO
NOT USE harsh chemicals or abrasive cleaners.
Move your new furniture carefully with two people. Lift and carry the unit.
Never push or drag the unit.
Do not allow children to climb or play on the unit. Failure to comply could
result in severe injury.
This unit has been designed to support the maximum loads shown.
Exceeding these load limits could cause unit sagging, instability, product
collapse and/or serious injury.
Additional parts are available for a nominal fee.
1-800-489-3351
www.Ameriwood.com/parts
10 lbs.
4.53 kg.
30 lbs
13.6 kg.
100 lbs.
45.3 kg.
10 lbs.
4.5 kg.
50 lbs.
22.6 kg.
50 lbs.
22.6 kg.
50 lbs.
22.6 kg.
10 lbs.
4.5 kg.
/