Canon MP730 User manual

User’s Guide

II

Preface

Copyright

reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any

language or computer language in any form or by any means, electronic, mechanical, magnetic,

optical, chemical, manual, or otherwise, without the prior written permission of Canon Inc.

Trademarks

Canon and BJ are registered trademarks. BCI, MultiPASS, UHQ, and ScanGear are trademarks of

Canon Inc.

All other product and brand names are registered trademarks, trademarks or service marks of

their respective owners.

As an ENERGY STAR® Partner, Canon Inc. has determined that this

product meets the ENERGY STAR® guidelines for energy efficiency.

Super G3 is a phrase used to describe the new generation of fax machines that

use ITU-T V.34 standard 33.6 Kbps* modems. Super G3 High Speed Fax

machines allow transmission time of approximately 3 seconds* per page

which results in reduced telephone line charges.

* Approximately 3 seconds per page fax transmission time based on ITU-T No. 1 Chart (Standard Mode) at

33.6 Kbps modem speed. The Public Switched Telephone Network (PSTN) currently supports 28.8 Kbps

modem speeds or lower, depending on telephone line conditions.

Preface

III



How to use the documentation provided

NOTE

• In addition to the above documentation, you can also refer to the online help in the software for online

information about a window or dialog box, and for step by step instructions on performing software

tasks. To access the online help, select or click [Help] in the software.

START HERE

After following instructions in the Set-Up

Sheet, we recommend you read this guide

to familiarize yourself with the basic

operation of all functions of your machine.

This guide, included as a PDF file in the

MultiPASS MP730/700 Setup CD-ROM,

includes instructions on functions that can

be performed directly from your machine

as well as detailed information on

memory cards. Refer to this guide for in-

depth instructions not included in the

Quick Reference Guide, or if you want to

learn more about advanced features.

This guide, included as a PDF file in the

MultiPASS MP730/700 Setup CD-ROM,

includes comprehensive instructions on

using the software. Refer to this guide for

full instructions on printing, scanning, and

faxing from your computer.

Be sure to read this sheet first!

This sheet includes instructions for setting up your machine and getting it ready for use.

Follow all steps in this sheet before using your machine.

Fax Model

Quick Reference Guide

User's Guide (This guide) Software Guide

Set-Up Sheet

Printed sheet

Printed manual

IV

Preface



Type conventions

Please read the list below of symbols, terms, and abbreviations used in this guide.

WARNING

Indicates a warning concerning operations that may lead to death or

injury to persons if not performed correctly. In order to use the

machine safely, always pay attention to these warnings.

CAUTION

Indicates a caution concerning operations that may lead to injury to

persons or damage to property if not performed correctly. In order to

use the machine safely, always pay attention to these cautions.

IMPORTANT

Indicates operational warnings and restrictions. Be certain to read

these items to operate the machine correctly, and to avoid damage to

the machine.

NOTE

Indicates notes for operation or additional explanations. Reading these is

highly recommended.

Indicates information exclusively for the MultiPASS MP730 model.

(



p. n-nn) Indicates a page number where additional information can be found.



Set-Up Sheet

Refer to the Set-Up Sheet for more details.



Quick Reference

Guide

Refer to the Quick Reference Guide for more details.



Software

Guide

Refer to the Software Guide (included in the CD-ROM) for more details.

machine General term used to represent the MultiPASS MP730 or MultiPASS MP700.

default A setting that remains in effect unless you change it.

document The original sheet(s) of paper you copy or scan with the machine.

menu A list of settings from which you select an item to set up or change. A menu

has a title which appears in the LCD.

[key name] Text enclosed in these brackets indicate a key name or item on the

computer you have to click, double-click, or point to.

<message> Text enclosed in these brackets indicate an LCD message.

click, double-click Term used to select or choose a command or option on your computer,

generally with a mouse.

Fax model only:

fax or document The original sheet(s) of paper you send or receive with the machine.

transaction number A four-digit number assigned automatically to any document you send or

receive.

TX/RX NO. Denotes

Transaction number

.

TX Denotes

Sending

.

RX Denotes

Receiving

.

Fax Model

Preface

V



Contents

1: Introduction

What your machine can do..................................... 1-1

Unpacking your machine ........................................ 1-2

Main components of the machine....................... 1-3

Operation panel of the machine...................... 1-4

2: Document handling

Document requirements......................................... 2-1

Loading documents .................................................. 2-2

Using the platen glass.......................................... 2-2

Using the ADF ........................................ 2-2

3: Print media handling

Recommended print media and

requirements................................................. 3-1

General print media guidelines........................ 3-4

Setting the paper thickness lever......................... 3-5

Setting the print media size and type................. 3-6

Loading print media.................................................. 3-7

Loading paper......................................................... 3-7

Loading envelopes................................................ 3-7

Loading banner paper ......................................... 3-9

4: Photo printing from a memory

card

Compatible memory cards ..................................... 4-1

Recommended print media ................................... 4-1

Inserting/removing a memory card .................... 4-2

Inserting a memory card..................................... 4-2

Removing a memory card .................................. 4-3

Printing methods........................................................ 4-4

Printing an index.................................................... 4-5

Printing all frames.................................................. 4-6

Printing a single frame......................................... 4-8

Printing a range of frames ................................4-10

DPOF (Digital Print Order Format)

printing..........................................................4-12

Setting vivid photo printing.................................4-14

Setting date printing...............................................4-14

Reading data from or writing data to a memory

card .................................................................4-15

Enabling/disabling overwriting

memory card data .....................................4-15

5: Copying

Documents you can copy........................................ 5-1

Making copies.............................................................. 5-1

Improving copied images ....................................... 5-1

Setting color or black & white copying.......... 5-1

Adjusting the image quality (resolution).......5-2

Adjusting the exposure (density) .....................5-2

Reducing or enlarging a copy ................................5-3

Using preset copy ratios ......................................5-3

Using custom copy ratios....................................5-3

Copying an image to ﬁt the page.....................5-3

Advanced copy features...........................................5-4

Copying two pages on a single page..............5-4

Borderless copying ................................................5-5

Repeating an image on a page .........................5-6

Creating a mirror image.......................................5-8

Shrinking an image to ﬁt the page ..................5-9

6: Registering information in

your machine

Guidelines for entering numbers, letters, and

symbols............................................................6-1

Registering required sender information...........6-2

Entering the sender information......................6-3

Setting the telephone line type.............................6-4

Setting daylight saving.............................................6-5

7: Speed dialing

Speed dialing methods.............................................7-1

Registering one-touch speed dialing ..................7-2

Changing or deleting an entry ..........................7-3

Registering coded speed dialing...........................7-4

Changing or deleting an entry ..........................7-5

Registering group dialing ........................................7-6

Changing or deleting an entry ..........................7-7

Using speed dialing....................................................7-8

Printing speed dialing lists ......................................7-9

8: Sending faxes

Documents you can fax............................................8-1

Sending methods .......................................................8-1

Memory sending ....................................................8-1

Manual sending ......................................................8-2

Improving faxed images...........................................8-3

Setting color or black & white transmission..8-3

Adjusting the image quality

(fax resolution)...............................................8-3

Adjusting the scan exposure..............................8-4

Dialing methods..........................................................8-4

Redialing a busy number .........................................8-5

Manual redialing.....................................................8-5

Automatic redialing...............................................8-5

Customizing automatic redialing

settings.............................................................8-5

Fax Model

VI

Preface

Sending the same document to several

recipients (sequential broadcasting).... 8-7

Documents stored in memory .............................. 8-8

Printing a list of documents in memory........ 8-8

Printing or deleting a document in memory.. 8-8

Checking a document’s details......................... 8-9

Special dialing............................................................8-10

Dialing through a switchboard.......................8-10

Switching temporarily to tone dialing .........8-10

9: Receiving faxes

Setting the receive mode........................................ 9-1

Receiving both faxes and voice calls

automatically: FAX/TEL AUTO SW........... 9-2

Customizing FAX/TEL AUTO SW ....................... 9-2

Receiving faxes automatically:

FAX ONLY MODE........................................... 9-3

Receiving with a DRPD (Distinctive Ring Pattern

Detection) service: DRPD .......................... 9-4

Setting the ring pattern....................................... 9-4

Receiving faxes manually: MANUAL MODE ...... 9-5

Receiving when an answering machine is

connected: ANS.MACHINE MODE .......... 9-6

Adjusting the answering machine .................. 9-6

Canceling receiving................................................... 9-6

10: Reports and lists

Summary of reports and lists ...............................10-1

ACTIVITY REPORT .....................................................10-2

Printing the ACTIVITY REPORT ........................10-2

Adjusting the ACTIVITY REPORT setting......10-2

Adjusting the TX REPORT setting .......................10-3

Adjusting the RX REPORT setting.......................10-4

Printing the USER’S DATA LIST.............................10-5

11: Maintenance

Replacing ink tanks..................................................11-1

When to replace an ink tank............................11-1

Guidelines...............................................................11-1

Replacing an ink tank .........................................11-2

Maintaining the printhead....................................11-3

Flowchart of printhead maintenance...........11-3

Printing the nozzle check pattern..................11-4

Cleaning the printhead......................................11-4

Aligning the printhead ......................................11-5

Cleaning your machine ..........................................11-7

Cleaning the exterior..........................................11-7

Cleaning the interior...........................................11-7

Cleaning the scanning area.........................11-7

Cleaning inside the machine ......................11-7

Cleaning the ADF area..................11-8

Cleaning the roller ..........................................11-9

12: Troubleshooting

Problems installing and removing software.. 12-1

Problems turning on the computer .................. 12-2

Problems printing from your computer .......... 12-2

Copying problems ................................................... 12-5

Problems scanning.................................................. 12-6

Problems receiving faxes ..................... 12-9

Problems sending faxes......................12-11

Telephone problems............................12-12

Problems using a memory card........................12-12

If nothing displays in the LCD (if there is no

power)..........................................................12-14

If the power disconnects

unexpectedly ............................................12-15

Removing jammed paper...................................12-15

Removing jams in the paper output tray ..12-15

Removing jams from the machine’s

interior.........................................................12-15

If there are repeated paper jams..................12-16

Removing jammed documents.......12-16

If the nozzle check pattern does not print

properly.......................................................12-18

Interpreting the messages..................................12-18

LCD messages.....................................................12-19

If you cannot solve the problem ......................12-23

13: Machine settings

Printing a list to check the current

settings.......................................................... 13-1

Accessing the machine settings ......................... 13-1

Settings........................................................................ 13-2

Menu: SPECIAL COPY .............................................. 13-2

Menu: MAINTENANCE ............................................ 13-2

Menu: USER DATA..................................................... 13-3

Menu: RECEIVE MODE............................ 13-6

Menu: MEMORY REFERENCE............... 13-6

Menu: REPORTS/LISTS ........................... 13-6

Menu: PHOTO PRINT MODE.................................. 13-7

Appendix: Speciﬁcations

General speciﬁcations .............................................. A-1

Ink speciﬁcations........................................................ A-3

Print speciﬁcations .................................................... A-4

Photo print speciﬁcations....................................... A-4

Copy speciﬁcations ................................................... A-4

Fax speciﬁcations...................................... A-5

Telephone speciﬁcations......................................... A-6

Index

......................................................................................I-1

Fax Model

Preface

VII



Safety information

Read this safety information thoroughly before using your machine, and keep it handy in case

you need to refer to it later.

WARNING

• This product emits low level magnetic flux. If you use a cardiac pacemaker and feel abnormalities,

please move away from this product and consult your doctor.

CAUTION

• Do not disassemble or modify. There are high-temperature and high-voltage components inside

the machine which may result in fire or electrical shock.

• Follow all warnings and instructions marked on the machine.

Location

WARNING

• Do not place the machine near alcohol, paint thinner, or

other flammable substances. If flammable substances

come into contact with electrical parts inside the

machine, it may result in fire or electrical shock.

CAUTION

• Do not place the machine on top of a carpet or rug which

has long pile. The threads may get inside the machine

and cause a fire.

• Place the machine on a flat, stable, vibration-free

surface that is strong enough to support its weight. (For

the weight of the machine, see the Appendix.)

• Do not place objects around the power plug so that you

are able to readily disconnect the power plug from the

wall socket at any time. Otherwise you will be unable to

disconnect the power plug in case of an emergency.

• Make sure the area is free from dust.

• Make sure the location is not affected by extreme

temperature changes, and always stays between 59° and

81.5°F (15° and 27.5°C).

• Make sure the relative humidity of the area is between 20%

and 80%.

• Keep the machine away from direct sunlight.

• Do not use or store the machine outdoors.

• Do not install the machine near devices that contain

magnets or generate magnetic fields, such as speakers.

VIII

Preface

Power Supply

WARNING

• Do not damage or modify the power cord and power

plug. Also do not place heavy objects on the power cord,

pull on it, or extensively bend it. These actions may

cause electrical damage and result in fire or electrical

shock.

• Do not insert or unplug the power plug with wet hands,

as this may result in electrical shock.

• Do not overload the wall outlet with too many electrical

appliances, as this may result in fire or electrical shock.

• Plug the machine into a standard 120 V AC, 60 Hz,

three-prong outlet. Operate the machine only from the

type of power source indicated on the machine’s label or

a fire, electrical shock or malfunction may occur. If you

are not sure of the type of power available, consult your

local power company.

• Do not allow the power cord to be near objects that emit

heat. The outer cover of the power cord may melt

resulting in fire or electrical shock.

• Make sure the power cord is fully extended and has no

knots in it when electricity is running through it. Knots

etc. in the cord may result in fire or electrical shock.

• Fully insert the power plug securely into the electrical

outlet. If the prongs of the power plug come into contact

with metallic objects etc., it may result in fire or

electrical shock.

CAUTION

• During electrical storms, turn off the power and

disconnect the power cord from the power outlet.

(Please note that any documents stored in the machine’s

memory will be deleted when you turn off the power.)

• Do not use an extension cord as this may result in fire or

electrical shock.

• Turn off the power and disconnect the power cord if the

machine will not be used for a long period such as

during holidays.

Preface

IX

Handling

IMPORTANT

• If dust accumulates around the plug of the power cord

when it is connected to a power outlet, unplug the

machine and wipe the plug with a clean, dry cloth.

• Do not plug the machine into the same circuit as

appliances such as an air conditioner, television, or copier.

These devices generate electrical noise which may

interfere with your machine’s operation.

• Whenever you turn off the power and unplug the machine,

wait at least five seconds before you plug it in again.

• Use only the power cord that came with the machine.

• Turn off the power and unplug the machine in the following conditions:

– When the power cord or plug is damaged or frayed.

– If liquid has spilled into the machine.

– If the machine has been exposed to rain or water.

– If the machine does not operate normally when you have followed the instructions in the guides

included with your machine. Adjust only those controls that are covered by the instructions in the

guides since improper adjustment of other controls may result in damage and will often require

extensive work by a qualified technician to restore the product to normal operation.

– If the machine has been dropped or damaged.

– If the machine exhibits a distinct change in performance, indicating a need for servicing.

WARNING

• Do not drop paper clips, staples, or other metal objects

inside the machine. Also do not spill water, liquid, or

flammable substances inside the machine. If these items

come into contact with high-voltage parts inside the

machine, it may result in fire or electrical shock. If these

items are dropped or spilled in the machine, turn off the

power and unplug the power cord immediately with dry

hands. Then contact the Canon Customer Care Center.

• Do not use any highly flammable sprays near the

machine. If gas from a spray comes into contact with the

electrical components inside the machine, it will result

in fire.

• There are high-voltage components inside the machine.

If you are looking inside the machine to remove paper

jams etc., do not allow metallic objects such as jewelry

to come into contact with the inside of the machine.

Contact may result in burns or electrical shock.

Fax Model

X

Preface

Maintenance

WARNING

• Do not service the machine yourself except as specifically described in this guide. If further

servicing is required, contact the Canon Customer Care Center.

• Keep the machine clean. Dust accumulation may prevent the machine from operating properly.

CAUTION

• Close the document cover and scanning unit gently to

avoid catching your hand. Failing to do so may result in

personal injury.

• Do not press down hard on the document cover or

ADF when using the platen glass to scan thick

books. This may damage the platen glass and/or result

in personal injury.

• Do not place the following objects on top of the machine. If such objects come into contact

with internal electrical components, the machine may short-circuit resulting in fire or

electrical shock.

– Metallic objects such as jewelry and watches

– Containers of water or other liquids such as glasses, vases, or pot plants

If water etc. does spill inside the machine, turn off the power immediately, disconnect the

power cord and contact the Canon Customer Care Center.

• Do not touch the high-voltage electrical parts as this may result in electrical shock.

• Do not place heavy objects on top of the machine as these may topple over and result in

injury.

• Do not insert your hands into the machine while it is printing as parts inside the machine are

moving and this may result in injury.

• After printing, do not touch the electrical contacts of the printhead. They will be hot and may

result in burns or electrical shock.

• Do not subject the machine to strong physical shock or

vibration.

• Turn off the power and unplug the machine before moving

it.

• Do not lift the machine by any of its attachments. Lift it by

the recessed areas on the sides of the machine.

•A distinct change in performance may indicate a need for

servicing.

Fax Model

Preface

XI



Legal limitation on usage of your product and the

use of images

Using your product to scan, print or otherwise reproduce certain documents, and the use of

such images as scanned, printed or otherwise reproduced by your product, may be prohibited

by law and may result in criminal and/or civil liability. A non-exhaustive list of these documents

is set forth below. This list is intended to be a guide only. If you are uncertain about the legality

of using your product to scan, print or otherwise reproduce any particular document, and/or of

the use of the images scanned, printed or otherwise reproduced, you should consult in advance

with your legal advisor for guidance.



Users in the U.S.A.

Pre-installation requirements for Canon facsimile equipment

A. Location

Supply a suitable table, cabinet, or desk. See the Appendix for the machine’s dimensions and weight.

B. Order information

1. Only a single line, touch-tone or rotary telephone set is to be used.

2. Order an RJ11-C modular jack (USOC code), which should be installed by the telephone

company. If the RJ11-C jack is not present, installation cannot occur.

3. Order a normal business line from your telephone company’s business representative. The

line should be a regular voice grade line or the equivalent. Use one line per machine.

DDD (DIRECT DISTANCE DIAL) LINE

-or-

IDDD (INTERNATIONAL DIRECT DISTANCE DIAL) LINE IF YOU COMMUNICATE OVERSEAS

NOTE

• Canon recommends an individual line following industry standards, e.g., the 2500 (Touch Tone) or 500

(Rotary/Pulse Dial) telephones. A dedicated extension off a PBX unit without “Call Waiting” can be used

with the MultiPASS MP730. Key telephone systems are not recommended because they send

non-standard signals to individual telephones for ringing and special codes, which may cause a fax error.

C. Power requirements

This equipment should be connected to a standard 120-volt AC, three-wire grounded outlet

only. Do not connect this machine to an outlet or power line shared with other appliances that

cause “electrical noise.” Air conditioners, electric typewriters, copiers, and machines of this sort

generate electrical noise which often interferes with communications equipment and the

sending and receiving of documents.

• Paper money

• Money orders

• Certificates of deposit

• Postage stamps (canceled or uncanceled)

• Identifying badges or insignias

• Selective service or draft papers

• Checks or drafts issued by governmental

agencies

• Motor vehicle licenses and certificates of title

• Traveler’s checks

• Food stamps

• Passports

• Immigration papers

• Internal revenue stamps (canceled or uncanceled)

• Bonds or other certificates of indebtedness

• Stock certificates

• Copyrighted works/works of art without permission

of copyright owner

XII

Preface

Connection of the equipment

This equipment complies with Part 68 of the FCC rules and the requirements adopted by the

ACTA. On the rear panel of this equipment is a label that contains, among other information, a

product identifier in the format US:AAAEQ##TXXXX. If requested, this number must be

provided to the telephone company.

The REN is used to determine the number of devices that may be connected to a telephone line.

Excessive RENs on a telephone line may result in the devices not ringing in response to an

incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be

certain of the number of devices that may be connected to a line, as determined by the total

RENs, contact the local telephone company. The REN for this product is part of the product

identifier that has the format US:AAAEQ##TXXXX. The digits represented by ## are the REN

without a decimal point (e.g., 03 is a REN of 0.3).

This equipment may not be used on coin service provided by the telephone company.

Connection to party lines is subjected to state tariffs.

In case of equipment malfunction

Should any malfunction occur which cannot be corrected by the procedures described in this

guide, disconnect the equipment from the telephone line or turn off the power and unplug the

power cord. The telephone line should not be reconnected or the power cord plugged in until

the problem is completely resolved. Users should contact Canon Authorized Service Facilities

for servicing of equipment. Information regarding Authorized Service Facility locations can be

obtained by calling the Canon Customer Care Center. (1-800-423-2366)

Rights of the telephone company

Should the equipment cause harm to the telephone network, the telephone company may

temporarily disconnect service. The telephone company also retains the right to make changes

in facilities and services which may affect the operation of this equipment. When such changes

are necessary, the telephone company is required to give adequate prior notice to the user.

FCC Notice

MultiPASS MP730: Facsimile Transceiver, Model H12269

MultiPASS MP700: H12270

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept an interference received, including interference that may cause

undesired operation.

NOTE

• This equipment has been tested and found to comply with the limits for a class B digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can

be determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

Preface

XIII

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV technician for help.

Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of the FCC

Rules.

Do not make any changes or modifications to the equipment unless otherwise specified in this

guide. If such changes or modifications should be made, you could be required to stop

operation of the equipment.

Canon U.S.A. Inc.

One Canon Plaza, Lake Success, NY 11042, U.S.A.

TEL No. (516) 328-5600

The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a

computer or other electronic device to send any message via a telephone fax machine unless

such message clearly contains in a margin at the top or bottom of each transmitted page or on

the first page of the transmission, the date and time it is sent and an identification of the

business or other entity, or other individual sending the message and the telephone number of

the sending machine or such business, other entity, or individual.

To automatically enter this information into your machine, follow the instructions on p. 7-1 or

p. 8-1 of this guide.



Users in Canada

Pre-installation requirements for Canon facsimile equipment

A. Location

Supply a suitable table, cabinet, or desk. See the Appendix for the machine’s dimensions and

weight.

B. Order information

1. Provide only a single-line to touch-tone or rotary telephone set terminated with a standard

4-pin modular phone plug. (Touch-tone is recommended if available in your area.)

2. Order an RJ11-C modular jack (USOC code), which should be installed by the telephone

company. If the RJ11-C jack is not present, installation cannot occur.

3. Order a normal business line from your telephone company’s business representative. The

line should be a regular voice grade line or equivalent. Use one line per machine.

DDD (DIRECT DISTANCE DIAL) LINE

-or-

IDDD (INTERNATIONAL DIRECT DISTANCE DIAL) LINE IF YOU COMMUNICATE OVERSEAS

NOTE

• Canon recommends an individual line following industry standards [e.g., the 2500 (touch tone) or 500

(rotary/pulse dial) telephones]. A dedicated extension off a PBX unit without “Camp On” signals is also

permissible with your MultiPASS MP730. Key telephone systems are not recommended because they

send non-standard signals to individual telephones for ringing and special codes, which may cause a fax

error.

XIV Preface

C. Power requirements

The power outlet should be a three-prong grounded receptacle (Single or Duplex). It should be

independent from copiers, heaters, air conditioners or any electric equipment that is

thermostatically controlled. The rated value is 120 volts and 15 amperes. The RJ11-C modular

jack should be relatively close to the power outlet to facilitate installation.

NOTICE

This equipment meets the applicable Industry Canada Terminal Equipment Technical

Specifications. This is confirmed by the registration number. The abbreviation, IC, before the

registration number signifies that registration was performed based on a Declaration of

Conformity indicating that Industry Canada technical specifications were met. It does not imply

that Industry Canada approved the equipment.

Cet appareil est conforme aux Spécifications techniques des équipements terminaux de

l’Industrie du Canada. Ceci est confirmé par le numéro d’enregistrement. L’abréviation IC

précédant le numéro d’enregistrement signifie que l’enregistrement a été effectué sur la base

de la Déclaration de conformité indiquant que le produit est conforme aux spécifications

techniques du Canada. Ceci n’implique pas que le produit ait été approuvé par l’industrie du

Canada.

Before installing this equipment, users should ensure that it is permissible to be connected to

the facilities of the local telecommunications company. The equipment must also be installed

using an acceptable method of connection. The customer should be aware that compliance

with the above conditions may not prevent degradation of service in some situations.

Repairs to certified equipment should be coordinated by a representative designated by the

supplier. Any repairs or alterations made by the user to this equipment, or equipment

malfunctions, may give the telecommunications company cause to request the user to

disconnect the equipment.

Users should ensure for their own protection that the electrical ground connections of the

power utility, telephone lines and internal metallic water pipe system, if present, are connected

together. This precaution may be particularly important in rural areas.

CAUTION

• Users should not attempt to make such connections themselves, but should contact the

appropriate electric inspection authority, or electrician, as appropriate.

IMPORTANT

• This Class B digital apparatus meets all requirements of the Canadian Interference-Causing

Equipment Regulations.

• Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel

brouilleur du Canada.

The Ringer Equivalence Number (REN) for this terminal equipment is 0.3. The REN assigned to

each terminal equipment provides an indication of the maximum number of terminals allowed

to be connected to a telephone interface. The termination on an interface may consist of any

combination of devices subject only to the requirement that the sum of the Ringer Equivalence

Numbers of all the devices does not exceed five.

Le Nombre d’équivalence Ringer (REN) de cet appareil terminal est 0.3. Le REN attribué à chaque

équipement terminal fournit une indication sur le nombre maximum de terminaux pouvant

être connectés sur une interface téléphonique. La terminaison sur une interface peut consister

en n’importe quelle combinaison d’appareils, à la condition seulement que la somme des

Nombres d’équivalence Ringer de tous les appareils ne soit pas supérieure à 5.

Preface XV

CANON CANADA INC.

1-800-OK-CANON

24 HOURS A DAY, SEVEN DAYS A WEEK

http://www.canon.ca

Chapter 1 Introduction 1-1

Chapter

1

Introduction



What your machine can do

Thank you for purchasing the Canon MultiPASS MP730 (indicated by the mark ) or the

MultiPASS MP700. Your machine incorporates the following functions in one simple-to-operate

device:

You may choose to use your machine as a stand-alone device for photo printing, copying, and

faxing. Alternatively, connect your machine to a computer and you will have a fully

integrated printer/photo printer/copier/scanner/ fax. The software provided with your

machine will allow you to perform a variety of tasks from your computer effortlessly and

efficiently.

Printer . . . . . . . . . . . . . . . . Print crisp, clear color or black & white documents from your

computer.

Photo printer . . . . . . . . . . Print photo-quality images from a memory card inserted directly

into your machine.

Copier . . . . . . . . . . . . . . . . . Make color or black & white copies from your machine. Also, apply

advanced copy features to your copies.

Scanner . . . . . . . . . . . . . . . Scan high-resolution images to your computer and process them

easily using the software provided.

Fax . . . . . . . . . . . . . Fax directly from your machine, or use your computer to send faxes.

Fax Model

1

Introduction

1-2 Introduction Chapter 1



Unpacking your machine

When you unpack your machine, check that you have the following components:

NOTE

•A USB cable is not included. You must purchase a USB cable (less than 16

#/8 ft./5 m) to connect your

machine to a computer.

• Paper output tray

• Printhead

• Multi-purpose tray

•Document tray

• Power cord

• Documentation

(Set-Up Sheet,

Quick Reference Guide)

• MultiPASS MP730/700

Setup CD-ROM

•Telephone line cord

•Destination labels

• Ink tanks

(Black, cyan, magenta, yellow)

• Tray cover

Fax Model

• MP700

• MP730

Fax Model

Machine

Chapter 1 Introduction 1-3

1

Introduction



Main components of the machine

Fax model shown here.

q ADF (Automatic Document Feeder) !0 Scanning unit (Printer cover)

w Feeder cover !1 [Open] button

e Document guides !2 Paper output tray

r Multi-purpose tray !3 Card slot

t Tray cover !4 Indicator light

y Automatic sheet feeder !5 Operation panel

u Document tray !6 Platen glass

i Document output slot !7 Printhead holder

o Document cover !8 Paper thickness lever

!7

!8

!6

eq w

!5

r

t

o

!0

!1

i

u

y

!3

!2

!4

Fax Model

1-4 Introduction Chapter 1

Operation panel of the machine

Fax model shown here.

q [Resume] key

Resumes an operation after an error is corrected. Also ejects a document remaining

in the ADF.

w In Use/Memory light

Blinks or lights during operation. Lights also when there are documents in the machine’s

memory.

e Alarm light

Blinks when an error occurs or when the machine needs attention.

r [Menu] key

Accesses the settings to customize operation of your machine.

t LCD

Displays messages and selections, and prompts during operation.

y [22

22

]([–]) and [33

33

] ([+]) keys

Scroll through selections, select the number of copies, and the photograph file number.

[2] also clears an entry and [3] enters a space between characters.

u [Set] key

Selects or confirms settings.

i [Enlarge/Reduce] key

Sets the copy enlargement or reduction ratio.

o [Paper Select] key

Selects the paper size and paper type for copying and received faxes.

!0 [Exposure] key

Selects the copy exposure and fax exposure.

!1 [Image Quality] key

Selects the copy resolution and fax resolution.

!2 [Copy] key

Switches the machine to copy mode.

!3 [Fax] key

Switches the machine to fax mode.

q w

e

!2

!7uytr !1!0oi !6

!3

!4 !5 @2 @3

!9 @1@0 @4 @5

@6

!8

Fax Model

Chapter 1 Introduction 1-5

1

Introduction

IMPORTANT

• To prevent the printhead from drying up, the machine automatically caps it when the power is

turned off with the [ON/OFF (1 sec.)] key. If you need to disconnect the machine from the main

power source (e.g. disconnect the power cord), be sure to turn off the machine first by pressing

[ON/OFF (1 sec.)] before disconnecting it.

• If you are not using the machine for a long period of time, we recommend that you print (in black

and color) or clean the printhead approximately once a month to maintain the printhead in good

working condition. The printhead contains high-precision nozzles that will become blocked if the

printhead is not used for a long period of time.

NOTE

• The power cannot be turned off when the machine is operating or when the In Use/Memory

light is on or blinking.

• Your machine performs printhead cleaning every time you turn on the machine. This ensures optimum

print quality, but also consumes a small amount of ink during the cleaning process. For this reason, it is

recommended that you always leave your machine turned on, and only turn it off when instructed to do

so in this guide, or when not using the machine for a long period of time (one month or more). This will

avoid unnecessary ink consumption.

!4 [Scan] key

Scans a document to your computer according to the action selected.

!5 [Photo Print] key

Switches the machine to photo card print mode.

!6 Numeric keys

Enter numerical values as well as fax/telephone numbers and characters.

!7 [Tone] key

Switches temporarily to tone dialing.

!8 [Color] key

Sets the machine for color copying and color sending.

!9 [Stop/Reset] key

Cancels operations and returns the machine to standby mode.

@0 [Start] key

Starts operations.

@1 [B&W] key

Sets the machine for black & white copying and black & white sending.

@2 [Redial/Pause] key

Redials the last number dialed with the numeric keys. Also enters pauses between or after

numbers when dialing or registering numbers.

@3 [Coded Dial] key

Press this key and a two-digit code to dial a pre-registered fax/telephone number or group.

@4 [Hook] key

Engages or disengages the telephone line.

@5 One-touch speed dialing keys

Dial a pre-registered fax/telephone number or group.

@6 [ON/OFF (1 sec.)] key

Turns the machine on and off (keep pressed for a brief interval). Before turning on the

machine, make sure the document cover is closed.

Fax Model

Page is loading ...

Canon MP730 User manual

This manual is also suitable for

Canon MP730 User manual

Related papers

Other documents