Delphi TNR800 - Navigation System With DVD-ROM Owner's manual

Brand
Delphi
Model
TNR800 - Navigation System With DVD-ROM
Type
Owner's manual
Delphi Touch Screen Navigation Radio - TNR800
DISCLAIMER – WARNINGS
Purchaser/Installer assumes all responsibility for damages and/or injuries incurred while and after
installing this product. Delphi is not responsible for damages resulting from kits installed incor-
rectly or individuals not following these instructions correctly.
READ ALL INSTRUCTIONS THROUGHLY BEFORE BEGINNING THE INSTALLATION
Do not attempt to install this radio in any application other than those specified. If you do,
there may be radio and vehicle functions that will not work properly.
Items included in the Kit:
Navigation Radio
GPS Antenna
Navigation DVD
Miscellaneous Installation Hardware
Owner’s Manual
•
•
•
•
•
BEFORE YOU BEGIN
Eject all CD’s from the factory radio. If you
don’t, the customer’s CDs may be trapped
in the old unit with no way to remove them.
Set the Parking Brake! If you don’t, the
vehicle could move during this procedure,
causing personal injury or damage to the
vehicle.
Turn the ignition key to the Off Locked:
position.
•
•
•
Delphi Touch Screen Navigation Radio
Installation Instructions
For 2003-2006 Denali and Escalade EXT & ESV & AMP Conversion ................................... 3 - 10
Tools needed for the Installation:
Phillips Head Screwdriver
Flat Screwdriver or Prying Device
7mm, 10mm, Extension and Drive
Bowl for holding screws
Estimated Installation Time - 1 hour.
For 2003-2006 Non-Class 2 Bose Amp Equipped Chevy and GMC Trucks and SUVs ...... 11 - 19
Tools needed for the Installation:
Phillips Head Screwdriver
Flat Screwdriver or Prying Device
7mm, 10mm, Extension and Drive
Pliers (needle nose and regular)
Soldering Iron (if preferred)
Bowl for holding screws
In addition to the Kit Items listed on the cover of this manual, a VSS Jumper is included for this
installation.
Estimated Installation Time - 1.5 - 2 hours.
For Professional Installation Assistance, call 1-877-667-8700
•
•
•
•
•
•
•
•
•
•
© 2006 Delphi Corp.
3
For 2003-2006 Denali and Escalade EXT & ESV & ASP Conversion
Remove the 30 amp fuse from the under hood electrical center.
The fuse is located in the bottom right corner of the box if you are standing on the driver’s
side of the vehicle looking toward the engine (see picture).
You can also look on the under side of the lid for location diagram.
Disconnect the Battery Negative Cable. WARNING: If you don’t, the vehicle could accidentally
start and move during this procedure and result in serious personal injury, including death.
Make sure the parking brake is engaged.
Remove Dash Bezel - Gently Snaps Off.
Tilt the steering wheel down and put the gear selector into 1st with the engine off.
With your fingers, start from the top right corner (corner above the radio - see picture) and
gently pull out
Continue around the top of the bezel and work to the sides and bottom.
NOTICE: Be careful when removing the bezel over the Emergency Light Switch located on top of the
steering column. This can scratch the bezel very easily.
Put gear selector back into Park.
1.
•
•
2.
3.
4.
•
•
•
•
Radio/Amp
Fuse
4
For 2003-2006 Denali and Escalade EXT & ESV & ASP Conversion
Remove the Radio
Remove the three screws and hold the radio in place. The screws are the only thing hold-
ing the radio in place, so hold the radio once the screws are removed.
Turn the key to the “On” position (with the engine off) and put the gear selector in 1st.
WARNING - Make sure the parking brake is set. If you don’t the vehicle could move and cause per-
sonal injury or damage to the vehicle.
Pull out the radio and disconnect the connections in the rear.
IMPORTANT: Some vehicles may have the wires caught on the dash structure behind the radio. This
prevents pulling out the radio and disconnecting the plugs. If your vehicle has this issue, you can ac-
cess the plugs by going through the AC controls area below the radio. Once the radio is removed, you
can maneuver the harnesses releasing it from the dash structure. There is enough wire that allows
the plugs to come out even with the front of the dash.
Coaxial Antenna Lead (pull perpendicular to the radio to remove).
XM/DVD/AUX plug (12-pin, if equipped).
Main radio connector (24-pin).
Put the gear selector in Park and turn the key to the “Off” position.
Remove the driver and passenger side A-Pillar trim.
There is only one clip at the top of the trim piece.
Pull on both sides diagonally away from the pillar.
You may have to remove part of the weather-stripping from around the door frame to get a
good grip on the A-Pillar trim.
To remove the weather-stripping, pull straight down to the middle of the door frame.
5.
•
•
•
•
•
•
6.
7.
•
•
•
•
5
For 2003-2006 Denali and Escalade EXT & ESV & ASP Conversion
Remove the fuse box trim from both sides of the dash.
With a flat screwdriver or flat tool, pry out both A/C vents on the passenger’s side of the dash.
Be careful not to scratch the dash trim or break the vent bezels with the prying tool.
You may want to wrap the tool in cloth to prevent damage to the dash parts.
Remove the Passenger Assist Handle.
Reach inside the A/C vent holes and and press the release tabs on both sides of the
handle.
Pull the handle away from the dash to remove the handle.
8.
9.
•
•
10.
•
•
2 Screws
Release
Tab
6
For 2003-2006 Denali and Escalade EXT & ESV & ASP Conversion
Remove the Top Dash Trim.
Remove two screws from each side of the dash.
Remove two screws from the passenger A/C vent location.
Remove remaining screws from the front of the dash trim.
Release the clips from each side of the dash by pulling out slightly.
Pull out on the dash trim above the passenger’s airbag (there are three clips in this location
that must be released before the trim can be removed).
Lift up the dash trim to disconnect the ambient light sensor.
NOTICE: When lifting up on the dash trim, be careful of the ambient light sensor wiring. There is not
much slack in the wiring and it could be torn from the sensor very easily.
Twist the ambient light housing (1/4 twist) to release the sensor from the dash pad.
This must be done before bringing the pad forward to remove.
11.
•
•
•
•
•
•
•
7
For 2003-2006 Denali and Escalade EXT & ESV & ASP Conversion
INSTALLATION
Install GPS Antenna.
Locate the screw slightly forward and to the right (passenger side) of the radio housing
area.
Remove the screw from the dash metal support.
Install GPS antenna and install the screw.
Route GPS antenna wiring under A/C pipe and to the radio area.
12.
•
•
•
13.
Screw
8
For 2003-2006 Denali and Escalade EXT & ESV & ASP Conversion
Install new Navigation Radio.
Connect radio connectors, GPS antenna, radio antenna and XM/DVD connector (if
equipped).
Install three screws.
Connect Battery Negative Cable.
Install 30A fuse in under-hood fuse box.
Test Radio.
Make sure parking brake is set.
Start vehicle.
Turn radio On.
Load DVD Navigation Disc.
Once disc checking is complete, press the “NAV” button if the navigation screen doesn’t
appear automatically. Make sure the vehicle is in position in an open, outside area so the
GPS antenna can link up to the satellites.
If the radio stations work and the navigation screen loads correctly, turn the radio Off, turn
the vehicle Off, and proceed to the next step.
If the radio isn’t working correctly, check all radio plugs in rear, as well as amp connections
and fuse.
14.
•
•
15.
16.
17.
•
•
•
•
•
•
•
Radio/Amp
Fuse
9
For 2003-2006 Denali and Escalade EXT & ESV & ASP Conversion
Install top dash trim.
Position trim to lock into the front tabs next to the windshield.
Connect ambient light sensor.
Once in position, push in clips located above passenger’s airbag.
Engage all remaining clips and make sure dash trim is in position.
Install screws on side of dash, in passenger A/C vents and front of trim.
NOTICE: Before installing the screws, make sure each of the clips located at the front of the dash (up
by the windshield) is in position. They are easy to miss.
Install passenger A/C vents, dash handle and A-pillar trim.
Align the dash handle with the holes and push into position. Check orientation as there is a
“top” and “bottom” to the handle. Slide the handle in and lock it.
A-pillar trim: align the tabs to the dash and press the metal clip into the upper hole.
Test the radio again.
Install the dash bezel.
Make sure the parking brake is set.
Tilt the steering wheel down and put the gear selector in to 1st with the engine off.
Roll the bezel in starting with the bottom first.
NOTICE: Be careful when moving the bezel over the emergency light switch located on the top of the
steering column. This can scratch the bezel very easily.
Align the clips and press into position.
Install fuse box covers on side of dash.
18.
•
•
•
•
•
19.
•
•
20.
21.
•
•
•
•
22.
2 Screws
10
For 2003-2006 Denali and Escalade EXT & ESV & ASP Conversion
Test Radio, A/C and Instrument Cluster for operation.
If everything works correctly, then continue.
If something doesn’t work correctly, check the connections or something that may have
been moved or bumped from the last time you tested.
Refer to the Owner’s Manual for setting up and operating the Navigation Radio.
Finished.
NOTES:
23.
•
•
24.
25.
11
For 2003-2006 Non-Class 2 Bose Amp Equipped Chevy and GMC Trucks and SUVs
Remove the 30 amp fuse from the under hood electrical center.
The fuse is located in the bottom right corner of the box if you are standing on the driver’s
side of the vehicle looking towards the engine (see picture).
You can also look on the under side of the lid for location diagram.
Disconnect the Battery Negative Cable. WARNING: If you don’t, the vehicle could accidentally
start and move during this procedure and result in serious personal injury, including death.
Make sure the parking brake is engaged.
Remove Dash Bezel - Gently Snaps Off.
Tilt the steering wheel down and put the gear selector into 1st with the engine off.
With your fingers, start from the top right corner (corner above the radio - see picture) and
gently pull out
Continue around the top of the bezel and work to the sides and bottom.
NOTICE: Be careful when removing the bezel over the Emergency Light Switch located on top of the
steering column. This can scratch the bezel very easily.
Put gear selector back into Park.
1.
•
•
2.
3.
4.
•
•
•
•
Radio/Amp
Fuse
12
For 2003-2006 Non-Class 2 Bose Amp Equipped Chevy and GMC Trucks and SUVs
Remove the Radio.
Remove the three screws and hold the radio in place. The screws are the only thing hold-
ing the radio in place, so hold the radio once the screws are removed.
Turn the key to the “On” position (with the engine off) and put the gear selector in 1st.
WARNING - Make sure the parking brake is set. If you don’t the vehicle could move and cause per-
sonal injury or damage to the vehicle.
Pull out the radio and disconnect the connections in the rear.
Coaxial Antenna Lead (pull perpendicular to the radio to remove).
XM/DVD/AUX plug (12-pin, if equipped).
Main radio connector (24-pin).
Remove the instrument cluster.
Remove the four 7 mm screws.
Retate the bottom of the cluster out and disconnect the plug on the back.
Squeeze the tabs and wiggle the connector to remove.
Put the gear selector in Park and turn the key to the “Off” position.
Remove the driver and passenger side A-Pillar trim.
There is only one clip at the top of the trim piece.
Pull on both sides diagonally away from the pillar.
You may have to remove part of the weather-stripping from around the door frame to get a
good grip on the A-Pillar trim.
To remove the weather-stripping, pull straight down to the middle of the door frame.
5.
•
•
•
•
•
•
6.
•
•
•
7.
8.
•
•
•
•
13
For 2003-2006 Non-Class 2 Bose Amp Equipped Chevy and GMC Trucks and SUVs
Remove the fuse box trim from both sides of the dash.
With a flat screwdriver or flat tool, pry out both A/C vents on the passenger’s side of the dash.
Be careful not to scratch the dash trim or break the vent bezels with the prying tool.
You may want to wrap the tool in cloth to prevent damage to the dash parts.
Remove the Passenger Assist Handle.
Reach inside the A/C vent holes and and press the release tabs on both sides of the
handle.
Pull the handle away from the dash to remove the handle.
9.
10.
•
•
11.
•
•
2 Screws
Release
Tab
14
For 2003-2006 Non-Class 2 Bose Amp Equipped Chevy and GMC Trucks and SUVs
Remove the Top Dash Trim.
Remove two screws from each side of the dash.
Remove two screws from the passenger A/C vent location.
Remove remaining screws from the front of the dash trim.
Release the clips from each side of the dash by pulling out slightly.
Pull out on the dash trim above the passenger’s airbag (there are three clips in this location
that must be released before the trim can be removed).
Lift up the dash trim to disconnect the ambient light sensor.
NOTICE: When lifting up on the dash trim, be careful of the ambient light sensor wiring. There is not
much slack in the wiring and it could be torn from the sensor very easily.
Twist the ambient light housing (1/4 twist) to release the sensor from the dash pad.
This must be done before bringing the pad forward to remove.
12.
•
•
•
•
•
•
•
15
For 2003-2006 Non-Class 2 Bose Amp Equipped Chevy and GMC Trucks and SUVs
INSTALLATION
Install GPS Antenna.
Locate the screw slightly forward and to the right (passenger side) of the radio housing
area.
Remove the screw from the dash metal support.
Install GPS antenna and install the screw.
Route GPS antenna wiring under A/C pipe and to the radio area.
13.
•
•
•
14.
Screw
16
For 2003-2006 Non-Class 2 Bose Amp Equipped Chevy and GMC Trucks and SUVs
Install included single wire between Instrument Cluster plug and radio plug.
NOTICE: Some vehicles may come with this wire installed from the factory (2004 and earlier don’t us-
ally have this wire). If you have the wire in position E of the 12-pin radio connector, skip this step.
Using the picture below, connect to the wire in position A4 on the instrument cluster con
-
nector (you can either use the included tap splice connector or solder the connection,
whichever you prefer).
Instrument Cluster Connector
Using the picture below, install the terminal end of the included wire in position E of the 12-
way radio connector.
Remove the locks from the plug using a small flat screw driver or other similar tool.
Before inserting into the connector, observe how the other terminals in the plug are orient
-
ed, and copy.
NOTICE: This terminal is delicate and can be bent easily under force. We recommend inserting the
terminal with your hands and using a plair of needle nose pliers to push it to the “lock” position. Grab
the terminal with the pliers as close to the back of the terminal as possible.
Check for continuity once wire is in position (circuit tester or light tester).
XM/DVD Connector
Install Instrument Cluster.
Install 4 screws.
15.
•
•
•
•
•
16.
•
17
For 2003-2006 Non-Class 2 Bose Amp Equipped Chevy and GMC Trucks and SUVs
Install new Navigation Radio.
Connect radio connectors, GPS antenna, radio antenna and XM/DVD connector (if
equipped).
Install three screws.
Connect Battery Negative Cable.
Install 30A fuse in under-hood fuse box.
Test Radio.
Make sure parking brake is set.
Start vehicle.
Turn radio On.
Load DVD Navigation Disc.
Once disc checking is complete, press the “NAV” button if the navigation screen doesn’t
appear automatically. Make sure the vehicle is in position in an open, outside area so the
GPS antenna can link up to the satellites.
If the radio stations work and the navigation screen loads correctly, turn the radio Off, turn
the vehicle Off, and proceed to the next step.
If the radio isn’t working correctly, check all radio plugs in rear, as well as amp connections
and fuse.
17.
•
•
18.
19.
20.
•
•
•
•
•
•
•
Radio/Amp
Fuse
18
For 2003-2006 Non-Class 2 Bose Amp Equipped Chevy and GMC Trucks and SUVs
Install top dash trim.
Position trim to lock into the front tabs next to the windshield.
Connect ambient light sensor.
Once in position, push in clips located above passenger’s airbag.
Engage all remaining clips and make sure dash trim is in position.
Install screws on side of dash, in passenger A/C vents and front of trim.
NOTICE: Before installing the screws, make sure each of the clips located at the front of the dash (up
by the windshield) is in position. They are easy to miss.
Install passenger A/C vents, dash handle and A-pillar trim.
Align the dash handle with the holes and push into position. Check orientation as there is a
“top” and “bottom” to the handle. Slide the handle in and lock it.
A-pillar trim: align the tabs to the dash and press the metal clip into the upper hole.
Test the radio again.
Install the dash bezel.
Make sure the parking brake is set.
Tilt the steering wheel down and put the gear selector in to 1st with the engine off.
Roll the bezel in starting with the bottom first.
NOTICE: Be careful when moving the bezel over the emergency light switch located on the top of the
steering column. This can scratch the bezel very easily.
Align the clips and press into position.
Install fuse box covers on side of dash.
21.
•
•
•
•
•
22.
•
•
23.
24.
•
•
•
•
25.
2 Screws
19
For 2003-2006 Non-Class 2 Bose Amp Equipped Chevy and GMC Trucks and SUVs
Test Radio, A/C and Instrument Cluster for operation.
If everything works correctly, then continue.
If something doesn’t work correctly, check the connections or something that may have
been moved or bumped from the last time you tested.
Refer to the Owner’s Manual for setting up and operating the Navigation Radio.
Finished.
NOTES:
26.
•
•
27.
28.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19

Delphi TNR800 - Navigation System With DVD-ROM Owner's manual

Brand
Delphi
Model
TNR800 - Navigation System With DVD-ROM
Type
Owner's manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents