VM Audio VMROCK6 Installation guide

Brand
VM Audio
Model
VMROCK6
Type
Installation guide

VM Audio VMROCK6 is a premium outdoor rock speaker, meticulously engineered to withstand the elements and deliver exceptional audio quality in any environment. Its durable fiberglass composite enclosure and aluminum grill provide robust protection against rain, snow, and extreme temperatures, ensuring years of reliable performance. The VMROCK6 features a versatile full-range coaxial dynamic driver, seamlessly combining a 6 1/2" PP cone woofer and a 1 1/2" mylar cone tweeter to deliver a rich and balanced sound with deep bass and crystal-clear highs.

VM Audio VMROCK6 is a premium outdoor rock speaker, meticulously engineered to withstand the elements and deliver exceptional audio quality in any environment. Its durable fiberglass composite enclosure and aluminum grill provide robust protection against rain, snow, and extreme temperatures, ensuring years of reliable performance. The VMROCK6 features a versatile full-range coaxial dynamic driver, seamlessly combining a 6 1/2" PP cone woofer and a 1 1/2" mylar cone tweeter to deliver a rich and balanced sound with deep bass and crystal-clear highs.

ROCK SPEAKERS
INSTALLATION GUIDE
VMROC6
1. Content
2. Routing
ROCK SPEAKERS
VMROC6
(2) Rock Speakers
1. Choose a permanent location to setup your new VM
Audio outdoor speaker.
2. Pre-route all cables from the amplier to the location of
the VMROC6 rock speakers.
Note: Keep your VM Audio speakers away from the
sprinkler system or an area where water may collect.
VM Audio Tech Support
US / Canada
phone: (855) audio-99 / (855) 283-4699
email: [email protected]
© VM Audio All rights reserved. All trade names are registered trademarks of
respective manufacturers listed.
Rev. 1
2013 COLLECTION
6. Specications
3. Installation
• Check that the speakers are connected to the cable
correctly.
• Check that the speaker cable is connected to the receiver
amplier correctly.
• Check that the receiver amplier is powered “on” at the
mains, is not on “mute”, has no headphones attached and
that the channels used for the exterior speakers (usually A or
B) is in operation.
• Refer to the owner’s guide that came with your receiver
amplier.
• Most initial problems are connectivity, please try a different
connection cable to your outdoor speakers or equipment.
• Check the “balance” control on your receiver amplier.
• Check all connections and cable to the inoperable speaker.
• Disconnect the “working” speaker from the receiver amplier
connection/channel. Switch the cord from the non-operating
speaker from its current connection to the “working” speaker
connection. If the speaker now works, the problem is your
receiver amplier.
• Reconnect as original. Remove the speaker cable at the
“working” speaker directly and connect it directly to the non-
working speaker. If the speaker now works, the problem is
somewhere in the original speaker cable.
• If the speaker still does not work the problem is the speaker.
• Follow same procedure as above for “No Sound”
No Sound
No Sound
from One
Speaker
Distortion
Speaker Drivers
Woofer
Tweeter
Enclosure
Grill
Frequency Response
Sensitivity
Power
Impedance
Dimensions
Full Range Co-axial Dynamic
6 1/2” PP Cone/Butyl Surround
1 1/2” Mylar Cone
Fiberglass Composite
Aluminum
60Hz - 20kHz
93dB
150W RMS / 300 PEAK
8 ohms
10.63” W x 7.87” H x 8.66” D
Use the color coding of the wires to be sure that positive
goes to positive and negative goes to negative at all the
connection points.
1. Strip off 1/2” of the insulation for each wire.
2. Twist together the two positive or negative wire leads.
3. Push one of the wire nuts onto the ends of the wires
and turn it until it is rmly set.
1. Sink the speaker wire 4-6” underground to prevent
accidental tripping over, pulling or other damages.
Warning! Check the intended path carefully to avoid
damaging any pre-laid plumbing or electric wiring.
5. Troubleshooting
4. Connections
  • Page 1 1
  • Page 2 2

VM Audio VMROCK6 Installation guide

Brand
VM Audio
Model
VMROCK6
Type
Installation guide

VM Audio VMROCK6 is a premium outdoor rock speaker, meticulously engineered to withstand the elements and deliver exceptional audio quality in any environment. Its durable fiberglass composite enclosure and aluminum grill provide robust protection against rain, snow, and extreme temperatures, ensuring years of reliable performance. The VMROCK6 features a versatile full-range coaxial dynamic driver, seamlessly combining a 6 1/2" PP cone woofer and a 1 1/2" mylar cone tweeter to deliver a rich and balanced sound with deep bass and crystal-clear highs.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents