2. Computers & electronics
  3. Audio & home theatre
  4. Loudspeakers
  5. VM Audio
  6. VMiS6

VM Audio VMiS6, VMiS8 Installation guide

  • Hello! I am an AI chatbot trained to assist you with the VM Audio VMiS6 Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
CEILING SPEAKERS
INSTALLATION GUIDE
VMiS6 / VMiS8
1. Content
2. Preparing
(2) Ceiling Speakers
1. Choose a location in your home to setup your new
VM Audio ceiling speaker.
Note: Keep in mind of the electrical and plumbing, make
sure the location of the speaker will not interfere with these
when installing.
VM Audio Tech Support
US / Canada
phone: (855) audio-99 / (855) 283-4699
email: [email protected]
© VM Audio All rights reserved. All trade names are registered trademarks of
respective manufacturers listed.
Rev. 1
3. Location
4. Cutout
1. Using the included template, position and outline the hole
on the ceiling.
2. Cut the hole using a drywall saw.
Note: Be sure there are no obstacles in the cutting area.
CEILING SPEAKERS
VMiS6 / VMiS8
2013 COLLECTION
Installation
•Ceiling installation should be located directly above the
listening area. In rooms larger than the bathroom or closet,
it is recommended to install additional speakers for better
performance.
•You may install a bracket where you will be placing the
speaker prior to installing drywall. Once insulation and drywall
is installed, you may cut the speaker hole.
•Use a stud-nder to locate the nearest wood or metal stud
and keep in mind the bafe ange will protrude outside of the
mounting hole.
Painting The Ceiling Speakers
•It is recommended to paint your speaker before installing into
your ceiling, or reverse the steps of installation to remove
the speaker for easy painting. For painting the installed
speaker, please use the paint mask in place of the grille. If
painting the grille, do not paint while attached to the speaker,
and be careful to not clog the holes, which will decrease
sound quality. VM Audio recommends only light spray
painting.
8. Troubleshooting
5. Routing
Use the color coding of the wires to be sure that positive
goes to positive and negative goes to negative at all the
connection points.
1. Strip off 1/2” of the insulation for each wire.
2. Twist together the two positive or negative wire leads.
3. Push one of the wire nuts onto the ends of the wires
and turn it until it is rmly set.
1. Prepare the cables and run them to the speaker and
amplier locations.
Note: Make sure the speaker location is free from any
electrical, plumbing, or AC duct.
7. Mounting
6. Connections
9. Specications
10. Notes
Speaker Drivers
Woofer
Tweeter
Bafe
Frequency Response
Sensitivity
Power
Impedance
Mounting Cutout
Full Range Co-axial Dynamic
6 1/2” PP Cone/Rubber Surround
1” Mylar Cone
ABS Material
75Hz - 20kHz
91dB
75W RMS / 300W PEAK
8 ohms
7.72 in. (19.60 cm)
• Check that the speakers are connected to the cable
correctly.
• Check that the speaker cable is connected to the receiver
amplier correctly.
• Check that the receiver amplier is powered “on” at the
mains, is not on “mute”, has no headphones attached and
that the channels used for the exterior speakers (usually A or
B) is in operation.
• Refer to the owner’s guide that came with your receiver
amplier.
• Most initial problems are connectivity, please try a different
connection cable to your outdoor speakers or equipment.
• Check the “balance” control on your receiver amplier.
• Check all connections and cable to the inoperable speaker.
• Disconnect the “working” speaker from the receiver amplier
connection/channel. Switch the cord from the non-operating
speaker from its current connection to the “working” speaker
connection. If the speaker now works, the problem is your
receiver amplier.
• Reconnect as original. Remove the speaker cable at the
“working” speaker directly and connect it directly to the non-
working speaker. If the speaker now works, the problem is
somewhere in the original speaker cable.
• If the speaker still does not work the problem is the speaker.
• Follow same procedure as above for “No Sound”
No Sound
No Sound
from One
Speaker
Distortion
1. Carefully remove the grille from the speaker assembly.
2. Turn the mounting feet towards the speaker cutout hole
and place the speaker into the ceiling.
3. Reinstall the grille into the slot in the bafe.
VMiS6
Speaker Drivers
Woofer
Tweeter
Bafe
Frequency Response
Sensitivity
Power
Impedance
Mounting Cutout
Full Range Co-axial Dynamic
8” PP Cone/Rubber Surround
1” Mylar Cone
ABS Material
60Hz - 20kHz
93dB
120W RMS / 350W PEAK
8 Ohms
9.45 in. (24.0 cm)
VMiS8
/