LifeGear 26355 Owner's manual

FOLDABLE RECUMBENT BIKE

ITEM NO.: 26355

OWNER’S MANUAL

IMPORTANT: Read all instructions carefully before using this product. Retain this

owner’s manual for future reference.

The specifications of this product may vary from this photo and are subject to change without

prior notice.

2015, July

1

TABLE OF CONTENTS

WARRANTY ------------------------------------------------------------------------------- 2

IMPORTANT SAFETY INSTRUCTIONS ------------------------------------------- 3

PARTS LIST ------------------------------------------------------------------------------- 4

TOOL ---------------------------------------------------------------------------------------- 5

OVERVIEW DRAWING ----------------------------------------------------------------- 6

FOOT PEDAL ASSEMBLY INSTRUCTIONS ------------------------------------- 7

HOW TO SET UP THE RECUMBENT BIKE -------------------------------------- 9

FOLDING STORAGE ------------------------------------------------------------------- 13

HOW TO MOVE THE RECUMBENT BIKE ---------------------------------------- 17

OPERATING THE COMPUTER ------------------------------------------------------ 18

ADJUSTMENTS -------------------------------------------------------------------------- 19

MAINTENANCE -------------------------------------------------------------------------- 20

TROUBLESHOOTING ------------------------------------------------------------------ 20

WARM UP AND COOL DOWN ROUTINE ----------------------------------------- 21

2

ONE YEAR LIMITED WARRANTY

LifeGear Inc. warrants to the original purchaser that this product is free from defects in

material and workmanship when used for the purpose intended, under the conditions that it

has been installed and operated in accordance with LifeGear's Owner's Manual. LifeGear's

obligation under this warranty is limited to replacing or repairing free of charge, any parts

which may prove to be defective under normal home use. This warranty does not include

any damage caused by improper operation, misuse or commercial application.

From the date of purchase, the frame is warranted to be free from defects for 1 (one) year.

This warranty is offered only to the original owner and is not transferable. Proof of

purchase is required.

When ordering replacement parts please have the following information ready:

1. Owner's Manual

2. Model Number

3. Description of Parts

4. Part Number

5. Date of Purchase

3

IMPORTANT SAFETY INSTRUCTIONS

Basic precautions should always be followed, including the following important

safety instructions when using this equipment. Read all instructions before using

this equipment.

1. Read all instructions and follow it carefully before using this equipment. Make sure the

equipment is properly assembled and tightened before use.

2. Before exercise, in order to avoid injuring the muscle, warm-up exercises are

recommended.

3. Please make sure all parts are not damaged and fixed well before use. This

equipment should be placed on a flat surface when using. Using a mat or other

covering material on the ground is recommended.

4. Please wear proper clothes and shoes when using this equipment; do not wear clothes

that may catch any part of the equipment; remember to tighten the pedaling straps.

5. Do not attempt any maintenance or adjustments other than those described in this

manual. Should any problems arise, discontinue use and consult your local dealer.

6. Do not use the equipment outdoors.

7. This equipment is for household use only. It is not a commercial model.

8. Only one person at a time should use this equipment.

9. If you feel any chest pains, nausea, dizziness, or short of breath, you should stop

exercising immediately and consult your physician before continuing.

10. Care should be taken in mounting or dismounting the equipment.

11. Do not allow children to use or play on the equipment. Keep children and pets away

from the equipment while in use. This machine is designed for adults use only. The

minimum free space required for safe operation is not less than two meters.

12. The maximum weight capacity for this product is 110 kgs.

WARNING: Before beginning any exercise program consult your

physician. This is especially important for the people who are over 35 years old or

who have pre-existing health problems. Read all instructions before using any

fitness equipment.

CAUTION: Read all instructions carefully before operating this product.

Retain this Owner’s Manual for future reference.

4

PARTS LIST

No. Description Qty No. Description Qty

001L Left Foot Pedal 1 024

Extension Hand Pulse Sensor

Wire

1

001R Right Foot Pedal 1 025 Front Main Frame Bushing 40x80 1

002 Screw M4x20 12 026 C-ring Ø15 1

003L Left Cover 1 027 Bearing 6202 1

003R Right Cover 1 028 Idle Wheel Axle Ø15x37 1

004 Belt (220J) 1 029 Washer Ø18xØ10.5 1

005 Belt (225J) 1 030 Hexagon Nylon Nut M10 1

006 Hexagon Nut M10 3 031 Bearing Cup Ø75x1.5T 2

007 Eyebolt M6x60 2 032 C-ring Ø17 6

008 Hexagon Nut M6 2 033 Bearing 6003Z 2

009 Washer Ø16xØ10.5x3T 2 034

Cross Recessed Pan Head

Tapping Screw M4x20

10

010 Bearing 6000Z 2 035 Transport Wheel Cap Ø60 2

011 Belt Wheel Ø150 1 036 Front Main Frame 1

012 Axle Ø14x99 1 037 Bearing Bracket Ø75x12.5 2

013L Left Crank 1 038 Rear Main Frame 1

013R Right Crank 1 039 Hand Pulse Sensor 2

014 Wire Grommet Ø16 1 040

Handlebar Foam Grip

Ø23xØ30x580 mm

2

015 Magnet Bracket 115x33 1 041L Left Handlebar Ø25.4 1

016 Magnet 12x12x3T 6 041R Right Handlebar Ø25.4 1

017

Sensor and Sensor Wire

(w/Sensor Bracket) (L=300 mm)

1 042

Handlebar Wire Grommet

Ø30xØ22

2

018

Cross Recessed Pan Head Bolt

M5x10

4 043 Spring Button 30x40 2

019 Computer FB013 1 044

Hand Pulse Sensor Wire

(L=700 mm)

2

020

Tension Control Knob

(L=600 mm)

1 045 Seat Cushion 1

021

Cross Recessed Pan Head Bolt

M6x15

9 046 Back Cushion 1

022 Tension Control Knob Bracket 1 047

Square End Cap (□30x30)

4

023 Seat Adjustment Knob M16 1 048

Rectangle End Cap (□30x60)

2

5

PARTS LIST

No. Description Qty No. Description Qty

049

Hexagon Socket Pan Head Cap

Bolt M8x45

2 064 Spring Ø8xØ1.0x50 1

050 Washer Ø8.5xØ18 4 065 Washer Ø5xØ12x1.5t 2

051 Back Cushion Tube 1 066 Wave Washer 1

052 Back Cushion Tube Knob M8x40 1 067 Magnet Wheel 1

053

Hexagon Socket Pan Head Cap

Bolt M10x140

2 068 Magnet Ø15x6 1

054 Washer Ø10.5xØ20 2 069 Belt Wheel with Crank Axle Ø155 1

055 Cap Nut M10 2 070 Crank Cover 2

056 Seat Frame 1 071 Washer Ø12xØ6 1

057 Rubber Pad Ø30x10 2 072 Handlebar End Cap Ø25.4 2

058

Cross Recessed Pan Head Bolt

M6x20

4 073 Hexagon Nut M8 1

059

Rear Stabilizer Adjustment Knob

M8

2 074 France Nut M10 2

060 Rear Stabilizer End Cap 30x60 2 075 Plastic Washer Ø22xØ11x1T 4

061 Adjustable Leveler M8x30 2 076

Cross Recessed Pan Head Bolt

M5x8

2

062L Left Rear Stabilizer 30x60x270 1 077 Rear Main Frame Bushing 30x60 1

062R Right Rear Stabilizer 30x60x270 1 078 Washer Ø14xØ6.5x1.5T 4

063

Hexagon Socket Pan Head Cap

Bolt M8x50

2 079

Cross Recessed Pan Head Bolt

M5x25

1

TOOL

Double Open End Wrench

1 PC

6

OVERVIEW DRAWING

39

40

41R

41L

42

34

43

44

21

45

46

47

48

49

50

52

53

54

55

57

34

38

63

59

62L

60

61

51

56

65

49

50

61

62R

60

72

54

55

53

40

42

43

21

72

44

39

65

34

59

63

50

14

2

3R

2

3L

34

2

34

35

19

76

36

1R

1L

4

5

6

7

8

9

6

7

9

18

17

18

15

20

18

22

23

24

21

25

26

27

28

29

30

21

31

32

33

37

64

66

67

69

68

16

79

71

70

13R

70

13L

73

74

75

2

77

78

58

8

6

10

11

10

12

24

7

FOOT PEDAL ASSEMBLY INSTRUCTIONS

STEP 1

The Foot Pedals, Pedal Shafts and Pedal Straps are marked “R” for Right and “L” for

Left.

Select the Right Foot Pedal Strap (1R) which has R marked on the side of the strap. Snap

the three hole end of the strap onto the inside edge of the Right Foot Pedal (1R). Snap the

other end of the strap onto the outside edge of the Right Foot Pedal (1R). Select

adjustment holes which allow your foot to be easily removed from the foot pedal.

Use the same procedure to snap the Left Foot Pedal Strap (1L) onto the Left Foot Pedal

(1L).

Left Foot Pedal Right Foot Pedal

1R

1L

8

1L

13L

1R

STEP 2

Insert the pedal shaft of Left Foot Pedal (1L) into threaded hole in the Left Crank (13L).

Turn the pedal shaft by hand in the counter-clockwise direction until snug.

Note: DO NOT turn the pedal shaft in the clockwise direction, doing so will strip the

threads.

Tighten the pedal shaft of Left Foot Pedal (1L) with the Double Open End Wrench provided.

Insert pedal shaft of Right Foot Pedal (1R) into threaded hole in Right Crank (13R).

Turn the pedal shaft by hand in the clockwise direction until snug.

Tighten pedal shaft of Right Foot Pedal (1R) with the Double Open End Wrench provided.

9

HOW TO SET UP THE RECUMBENT BIKE

STEP 1

Put one foot behind the front stabilizer of the Front Main Frame (36). One hand grasps the

handle or Rear Main Frame (38) and the other hand to turn the Seat Adjustment Knob (23) in

a counterclockwise direction until it can be pulled out. Pull out the Seat Adjustment Knob

(23) and then slide the Rear Main Frame (38) back or forth direction to the suitable position.

Lock the Rear Main Frame (38) in place by releasing the Seat Adjustment Knob (23) and

sliding the Rear Main Frame (38) back or forth slightly until the Seat Adjustment Knob (23)

"pops" down into the hole of the Rear Main Frame (38). For added safety, tighten the

Seat Adjustment Knob (23) in a clockwise direction.

NOTE: When adjusting the seat back or forth direction, make sure the bushing does

not exceed the mark line on the Rear Main Frame.

Handle

38

23

36

10

STEP 2

Remove two Rear Stabilizer Adjustment Knobs (59) from the Rear Main Frame (38).

Pull both Left and Right Rear Stabilizers (62L, 62R) up and align knob holes.

Secure both Left and Right Rear Stabilizers (62L, 62R) in place by tightening both Seat

Adjustment Knobs (23) in a clockwise direction.

STEP 3

One hand grasps the Left or Right Handlebar (41L, 41R) and then pull it up.

62 L

62L

59

62R

38

62 R

59

41L

41R

11

STEP 4

Press down the Spring Button (43) on the Left Handlebar (41L) and then push the Left

Handlebar (41L) down until the Spring Button (43) is locked in the other adjustment hole on

the Seat Frame (56).

Use the same procedure to push down the Right Handlebar (41R).

41L

56

43

41L

41R

56

41R

43

12

STEP 5

Pull the Back Cushion (46) up and align knob hole.

Secure the Back Cushion Tube (51) in place by tightening the Back Cushion Tube Knob (52)

in a clockwise direction.

38

52

51

52

51

46

13

FOLDING STORAGE

STEP 1

Loosen the Back Cushion Tube Knob (52) in a counterclockwise direction until it can be

pulled out.

Push the Back Cushion (46) down.

52

51

46

14

STEP 2

Press down the Spring Button (43) on the Left Handlebar (41L) and then pull the Left

Handlebar (41L) up until the Spring Button (43) is locked in the other adjustment hole on the

Seat Frame (56).

Use the same procedure to pull up the Right Handlebar (41R).

STEP 3

One hand grasps the Left or Right Handlebar (41L, 41R) and then pull it down.

41L

43

56

41L

41R

43

56

41L

41R

15

STEP 4

Put one foot in front of the front stabilizer of the Front Main Frame (36). One hand grasps

the handle or Rear Main Frame (38) and the other hand to turn the Seat Adjustment Knob

(23) in a counterclockwise direction until it can be pulled out. Pull out the Seat Adjustment

Knob (23) and then slide the Rear Main Frame (38) back direction to the folded position.

Lock the Rear Main Frame (38) in place by releasing the Seat Adjustment Knob (23) and

sliding the Rear Main Frame (38) back or forth slightly until the Seat Adjustment Knob (23)

"pops" down into the hole of the Rear Main Frame (38). For added safety, tighten the

Seat Adjustment Knob (23) in a clockwise direction.

Handle

23

38

36

16

STEP 5

Remove two Rear Stabilizer Adjustment Knobs (59) from the Rear Main Frame (38).

Pull both Left and Right Rear Stabilizers (62L, 62R) down and align knob holes.

Secure both Left and Right Rear Stabilizers (62L, 62R) in place by tightening both Seat

Adjustment Knobs (23) in a clockwise direction.

59

62R

59

62L

59

62L

17

Folded Position

Handle

Transport Wheel Cap

Handlebar

Set Up Position

Handle

Transport Wheel Cap

Handlebar

HOW TO MOVE THE RECUMBENT BIKE

This recumbent bike has a pair of Transport Wheel Caps on the both ends of the front

stabilizer and can be carefully tilted onto its Transport Wheel Caps for easy moving and

storage. To move the recumbent bike, firmly grasp the Handle with both hands. Next,

carefully lift the recumbent bike up until it rolls freely on the Transport Wheel Caps.

CAUTION: It is suggested you always use the aid of a second person when moving

the recumbent bike.

18

OPERATING THE COMPUTER

USING YOUR COMPUTER

The computer can be activated by pressing the button or by pedaling.

If you leave the equipment idle for 4-5 minutes, the power will turn off

automatically.

BUTTON FUNCTIONS:

Press the button to select the functions of the computer.

Press and hold the MODE button for 3 seconds to reset all data values

to zero except the ODO (ODOMETER) data values.

COMPUTER FUNCTIONS:

SCAN: Automatically scans each function in sequence with change every 4 seconds.

SPEED: Displays the current training speed.

TIME: Displays your elapsed workout time in minutes and seconds.

ODO (ODOMETER): Displays the total accumulative distance travelled. The ODOMETER

data values can not be clear to zero by pressing and holding the button for 3 seconds. If

you take out the batteries from the computer, the ODOMETER data values will clear to zero.

DIST (DISTANCE): Displays the cumulative distance travelled during workout.

CAL (CALORIES): Displays approximate amount of calories burned during workout.

(This data is a rough guide for comparison of different exercise sessions and should not be

used in medical treatment).

PULSE: Displays your current heart rate figures after you grip the handlebar pulse sensors

with both your hands during exercise. To ensure the pulse readout is more precise, please

always hold on to the handlebar pulse sensors with two hands instead of just with one hand

only when you try to test your heart rate figures.

HOW TO INSTALL THE BATTERIES:

1. Remove the battery cover on the back of the computer.

2. Place two size AAA batteries into the battery housing.

3. Insure batteries are correctly positioned and battery springs are in proper contact with

batteries.

4. Re-install the battery cover.

5. If the display is illegible or only partial segment appears, remove batteries and wait 15

seconds before reinstalling.

19

ADJUSTMENTS

Adjusting the Tension Control Knob

To increase the tension, turn the

Tension Control Knob in a clockwise

direction.

To decrease the tension, turn the

Tension Control Knob in a

counterclockwise direction.

Adjusting the Adjustable Leveler

Turn the Adjustable Leveler on the left

or right rear stabilizer as needed to

level the recumbent bike.

Adjusting the Seat Forward or Back

One hand grasp the Handle or Rear

Main Frame and the other hand to turn

the Seat Adjustment Knob in a

counterclockwise direction until it can

be pulled out. Pull out the Seat

Adjustment Knob and then slide the

Rear Main Frame back or forth

direction to the suitable position. Lock

the Rear Main Frame in place by

releasing the Seat Adjustment Knob

and sliding the Rear Main Frame back

or forth slightly until the Seat

Adjustment Knob "pops" down into the

hole of the Rear Main Frame. For

added safety, tighten the Seat

Adjustment Knob in a clockwise

direction.

NOTE: When adjusting the seat back

or forth direction, make sure the

bushing does not exceed the mark

line on the Rear Main Frame.

Tension Control Knob

Adjustable Leveler

Seat Adjustment Knob

Handle

Rear Main Frame

Page is loading ...

LifeGear 26355 Owner's manual

LifeGear 26355 Owner's manual

Related papers

Other documents