4Sight 4SK010 Operating Instructions Manual
- Category
- Drive recorders
- Type
- Operating Instructions Manual
4SK010
Operating Instructions
Camera key features:
1. Up arrow
2. Menu / Back arrow
3. Down arrow / MIC switch
4. OK key
5. Mode key
6. SOS
7. Memory card socket
8. Power button
9. AV-OUT Socket
10. MIC
11. Reset
12. micro USB power connector
13. The power led
14. Video recording / standby indicator
Accessories
Micro USB cable
Micro USB car charger
Mount
Memory card
Memory card reader
Functional operation
Installation
Easy to install onto any windshield, and the 12V charger will fit any vehicles 12V outlet.
Charging:
A. Powered by a rechargeable lithium-ion battery
Two methods of charging the Dash Cam. One way is through the supplied
charger, and the second method is by using the supplied microUSB cable using
your computer.
B. connect 12V car charger
When powering on your vehicle, the unit will automatically power on. When you
power down your vehicle, the Dash Cam will take up to 5 seconds to power off
and automatically save the previously recorded file.
Note: You must only use 5V output voltage. It is recommended that you always
use the original charger, as it was designed to work with your Dash Cam. Some
vehicles have constant 12V power flowing from the 12V outlet. In this case, you
must long press the power button on your Dash Cam to shut it down.
Video mode
When the Dash Cam is powered on, it enters Video mode. If the unit has a TF memory
card inserted, it will automatically start recording. When the unit is recording, the green
indicator light will blink. If the green indicator light is solid, the unit is not recording and is
in standby mode.
Emergency lock
While the unit is recording, you can press the MODE/SOS (5) button to lock the
currently recording file. Locking a file will make it un eligible to be recorded over during
the looping procedure.
Photo mode
While recording is stopped, short press the MODE / SOS button one time. This brings
you to the Photo mode. While you are in Photo mode, the OK button is the snapshot
button.
Browse and delete files
Power on your unit, stop the recording and hit the Menu button. This will bring you to the
menu options. Use the up and down buttons to navigate the first menu option, and use
the screen toggle button to change menus.
Menu Settings
Power on your unit, stop the recording and hit the Menu button. This will bring you to the
menu options. Use the up and down buttons to navigate the first menu option, and use
the screen toggle button to change menus.
1. Video settings
1.1 Video mode: 1920 x 1080p 30fps | 1280 x 720p 60fps | 1280 x 720p 30fps | 640
x 480 30fps
1.2 Video quality: Super fine and Fine
1.3 Movie clips: 25min, 10min, 5min, 3min, 2min, 1min, and off.
1.4 Motion detection video: 5 Seconds ,10 Seconds (The default), 30 Seconds and
1 Minute
1.5 Sound recording: On (Default), Off
1.6 LDWS: On, Off (Default) (Lane Departure Warning System)
1.7 FCWS: On, Off (Default) (Front Car Warning System)
2. Photo settings
2.1 Image size: 3M, 2M (default), 1.2M, VGA
2.2 Image quality: Super Fine, Fine
3. Card Setup
3.1 Format card: Yes, No (The default)
3.2 Card information: Displays how much video time you would have with the
different resolution options that are available. This option also shows you the number of
Photos you can take with each specific resolution setting.
4. system settings
4.1 Beep: On (Default), Off
4.2 Volume: shows 0,1,2,3,4,5 (default), 6,7,8,9,10 bars, the greener bars, the louder
the unit’s sound will be.
4.3 Clock settings: Use the up and down buttons
4.4 Date format: none, YYYY MM DD | MM DD YYYY | DD MM YYYY |
4.5 Stamp: Date + Logo (Default), Date, Logo, off (When off is selected, video will not
show time.
4.6 Language select: English (Default), Español, Português, Русский, Chinese
Simplified and traditional Chinese, Deutsch, Italiano ,Latviski, Polski, Română,
Slovenč
4.7 Frequency rate (flicker): 50 Hertz (Default), 60 Hertz
4.8 Automatically turn off the screen: Off, 1 Min (Default), 3 Min
4.9 LED Fill light: On, Off (The default)
4.10 Protect Level (G-Sensor): Off, 0,1, 2 (default), 3, 4
4.11 Parking Monitor: Off (Default) High, Middle, Low
4.12 Motion detection: off (Default) Low, Medium, High
4.12.1 Time zone selection:
Examine the diagram below fully to set your GMT setting correctly per your location.
4.13 System reset: Yes, No (The default)
4.14 WIFI CARCAM: On (Default), Off
4.15 LDWS Calibration: Manually calibrate perspective lines
4.16 Firmware version: displays the current firmware version
Download file
Remove the TF Card, insert the memory card into the memory card reader, insert
reader into USB port on your computer. Find the storage device in which the files
reside, copy and paste the files you would like to download onto your computer.
AV-OUT Video / Audio output
2.5MM Headphone to RCA plug is used to connect your Dash Cam to any screen that
supports a RCA input.
Considerations
1. Please insert TF card before powering on the unit.
2. Please use the included microUSB Car charger for powering the Dash Cam, the car
charger included 12V-5V Adapter. If the output voltage is greater than 5V that will burn.
Technical parameters
1. Video resolution: (1920 x 1080 1280 x 720 640 x 480)
2. Compression format: H.264
3. Cycle recording / motion detection / parking monitor
4. Power supply: rechargeable lithium-ion battery /micro USB car charger
5. Supported TF card: supports up to 256GB
6. Sound: recording options off or on
7. External interface: AV-OUT Audio / video output
8. Display: 2.7 - inch display
-
1
-
2
-
3
-
4
-
5
-
6
-
7
4Sight 4SK010 Operating Instructions Manual
- Category
- Drive recorders
- Type
- Operating Instructions Manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
