Follett Maestro Chewblet 400 Series Installation, Operation And Service Manual

Follett
Brand
Follett
Model
Maestro Chewblet 400 Series
Category
Ice cube makers
Type
Installation, Operation And Service Manual
Follett
®
Maestro
™
Chewblet
®
400 Series
Ice Machine and Top Kit
for Lancer countertop ice and beverage dispensers
2
0
8
2
6
4
U
L
R
U
L
R
C
N
S
F
Installation, Operation and Service Manual
00117267R04
801 Church Lane • Easton, PA 18040, USA
Toll free (877) 612-5086 • (610) 252-7301
www.follettice.com
Following installation, please forward this manual
to the appropriate operations person.
Order parts online
www.follettice.com
2 Maestro 400 Series Top Kit for Lancer
Welcome to Follett Corporation
Important cautions
Speci cations
Installation
Cleaning/descaling and sanitizing
Replacement Parts
Models MTL22SC, MSL22SC
Models MTL30SC, MSL30SC
Table of contents
3
3
4
7
15
17
17
18
Maestro 400 Series Top Kit for Lancer 3
Welcome to Follett
Follett equipment enjoys a well-deserved reputation for excellent performance, long-term reliability and
outstanding after-the-sale support. To ensure that this equipment delivers that same degree of service, we
ask that you review the installation portion of this manual before beginning to install the unit. Our installation
instructions are designed to help you achieve a trouble-free installation. Should you have any questions or
require technical help at any point, please call our technical service group at (877) 612-5086 or (610) 252-7301.
Note: To expedite assistance, all correspondence or communication MUST include the model number, serial
number and complete and detailed explanation of the problem.
Before you begin
After uncrating and removing all packing material, inspect the equipment for concealed shipping damage. If
damage is found, notify the shipper immediately and contact Follett Corporation so that we can help in the  ling
of a claim, if necessary.
Check your paperwork to determine which model you have. Follett model numbers are designed to provide
information about the type and capacity of Follett equipment. Following is an explanation of the different model
numbers in the series.
Important cautions
Dispenser bin area contains mechanical, moving parts. Keep hands and arms clear of this area
at all times. If access to this area is required, power to unit must be disconnected  rst.
Follett recommends a Follett water  lter system be installed in the ice machine inlet water line
(standard capacity #00130299, high capacity #00978957, carbonless high capacity #01050442).
Ice is slippery. Maintain counters and  oors around dispenser in a clean and ice-free condition.
Ice is food. Follow recommended cleaning instructions to maintain cleanliness of delivered ice.
!
MSL22SC
Ice machine configuration
SC = self-contained
Dispenser size
22 = 22" wide
24 = 24" wide
30 = 30" wide
44 = 44" wide
Dispenser manufacturer
C = Cornelius
L = Lancer
S = SerVend
Ice machine mounting
MT = Maestro top mount
MS = Maestro RIDE
®
model
4 Maestro 400 Series Top Kit for Lancer
Speci cations
Electrical
Model number Full load amps Max. fuse size
MC400 series ice machine 115/60/1 11.0 amps 20 amps
Ambient speci cations
Air temperature 100 F/38 C max. 50 F/10 C min. (best performance below 80 F/27 C)
Water temperature 90 F/32 C max. 40 F/4 C min. (best performance below 70 F/21 C)
Water pressure 70 P.S.I. max. (482kPA) 10 P.S.I min. (89kPA)
Plumbing
Your new ice machine is equipped with a drain line to simplify draining the evaporator and  oat reservoir. The
tube labeled “ oat/evap drain” is for SERVICE USE ONLY and must NOT be connected to the ice machine drain.
Water line sizes Make up water (inlet to  oat) 1/4" min.
Condenser (water-cooled only) 3/8" min.
Drain line sizes Ice machine drain 3/4" min.
Condenser (water-cooled only) 1/2" min.
Slope to drain 1/4" per foot (6mm per 30.4cm run) 1/2" min.
• Water shut-off recommended within 10 feet (3m), drain to be hard-piped and insulated
• Separate drains for ice machine and condenser. To prevent back  ow, do NOT connect drains.
• Follett recommends a Follett water  lter system be installed in the ice machine inlet water line (standard
capacity #00130299, high capacity #00978957, carbonless high capacity #01050442).
Field Wiring: countertop and wall mount dispensers with RIDE
®
remote ice
delivery model ice machines
Consult enclosed D400A/W, R400A/W, MCD400A/W manual.
Maestro 400 Series Top Kit for Lancer 5
20.75" (527 mm)
22.75" (578 mm)
13.00"
(331 mm)
4.875"
(124 mm)
2.375"
(61 mm)
1.875" (48 mm)
7.00" (178 mm)
A
A
B
B
F
F
D
E
C
A
B
C
C
17.00"
(432mm)
20.75" (527 mm)
17.00"
(432 mm)
L
U
L
U
RR
NSF
NSF
Front view — air-cooled
remote mount
Side view — air-cooled
remote mount
Top back view — air-cooled
top mount
Front view — water-cooled Side view — water-cooled
12.875"
(327 mm)
4.75"
(121 mm)
8.375"
(213 mm)
2.25"
(57 mm)
1.875" (48 mm)
6.875"
(175 mm)
2"
(51 mm)
Dimensions and clearances
Required clearances – MCD400 series
Entire front of ice machine clear of obstruction/connections to allow removal.
12" (305 mm) above ice machine for service
6" (153 mm) minimum between louvered (exhaust) side of ice machine and any adjacent equipment.
MCD400AHS – 18" (457 mm) minimum, 10 ft (3 m) maximum between discharge and air intake grilles.
A – 3/4" MPT drain
B – 3/8" OD push-in water inlet
C – Electrical cord
D – 3/8" FPT condenser inlet
E – 1/2" FPT condenser drain
F – Bin signal cord
6 Maestro 400 Series Top Kit for Lancer
Installation
1. Install Lancer ice dispenser according to manufacturer’s speci cations.
Note: We recommend that the dispenser back be mounted at least 1" (26mm) from wall to allow water, drain
and electric lines from top mount ice machines to be concealed behind dispenser.
2. Disconnect power to dispenser.
3. Remove front panel/merchandiser from the dispenser.
4. Adjust the agitation timer located on Lancer PC board to 1 second on (Fig. 1.1) – 2 1/2 hours off (Fig. 1.2).
PRESS IN ON
THIS SIDE TO
TURN SWITCH
ON.
SWITCH
ON
SWITCH
OFF
PRESS IN ON
THIS SIDE TO
TURN SWITCH
OFF .
R OCKER
SWITCHES
(VIEW LOOKING
DO WN)
SIDE VIEW
SIDE VIEW
1
2
3
4
5
6
7
8
OFF
SWITCH
NUMBER
A GIT A TION FREQUENCY
NO A GIT A TION
10
MINU
TE
S
2
0 M
I
NUTES
3
0 MINUTES
4
0 MIN
U
TES
50 MI
N
U
T
ES
60 MINUTE
S
70 MINUT
ES
80 MINUTE
S
90
MIN
UTES
100 MIN
U
TES
110
MIN
U
TES
120
MIN
UTES
130 MINUTES
140 MIN
U
TES
150
MINUTES
5
6
7
8
O
O
O
O
O
O
O
X
O
O
X
O
O
O
X
X
O
X
O
O
O
X
O
X
O
X
X
O
O
X
X
X
X
O
O
O
X
O
O
X
X
O
X
O
X
O
X
X
X
X
O
O
X
X
O
X
X
X
X
O
X
X
X
X
SWITCH
NUMBER
A GIT A TION TIME
1 SEC
OND
2 SECONDS
3
SEC
ONDS
4
SECONDS
3
4
O
O
O
X
X
O
X
X
X = ON
O = OFF
1
2
Fig. 1
Maestro 400 Series Top Kit for Lancer 7
Agitation adjustments - Lancer FS Series
Major/Minor
FS-16 Setup
Config Bonus Key
Soda/Plain Water
Config Dispense Only
PC Mode
PC Time
Ice Stir Off
Ice Stir On
Sold Out
Carb Sensors
Ice Bin Sensors
Valve Code Version
Number Of Valves
Reset Defaults No Yes
Reload Defaults?
1 2 3 4
12 0.104 0.104
1000
Ice Bin Optic
Upper Lower
Sold Out #1
Selection Sold Out
05000
On Time (MSEC)
Off On
Set PC Mode Menu
V:1 B1 DLY1
Dispense Delay
V:2 1:S 2:W 3:S 4:W
V:1 T:F M:S B:W
Bonus Key Setup
Brands Per Side
V:1 L:2 R:1
FS-16 Setup
FS-16 Setup
FS-16 Setup
FS-16 Setup
FS-16 Setup
FS-16 Setup
FS-16 Setup
FS-16 Setup
FS-16 Setup
FS-16 Setup
FS-16 Setup
FS-16 Setup
FS-16 Setup
Soda/Plain Water
OFF Time (MIN)
00150
On Time (MSEC)
01000
1000 500
34 0.104 0.104
On On On On
V:1 B:1
Sold Out #1
Off
Sold Out #1
Ver. 0.200
Lancer FS-16
Sub-CatagoryMain Menu
Initialization Screen
2nd Sub-Catagory
(Boot Up Only)
Cancel
Enter
Scrolls through Main Menu
Press "Enter" to enter sub-catagory
Moves curser to right or left
Changes value (number/letter)
Press "Enter" to enter save changes
Press "Cancel" to exit menu
➊
Lancer FS series only
1. Hold down "cancel" and "left button" to get to hidden menu
➊
.
2. Type in code 6655.
3. Type in 150 minutes of off time and 1000 milliseconds (1 second of time) as the preferred setting.
Note: See Lancer manual for more information.
8 Maestro 400 Series Top Kit for Lancer
2
0
8
2
6
4
U
L
R
U
L
R
C
N
S
F
Fig. 4
Top mounted ice machine installation
9. Position Follett MCD400AHT ice machine on perimeter
gasket of stainless steel top. Ice machine should be
oriented with A/C condenser facing front (Fig. 4).
8. Install supplied stainless steel top with access opening
toward front of dispenser (Fig. 3).
For dispensers with top mounted ice machines
Proceed with steps 9 through 17.
For dispensers with RIDE model ice machines
Go directly to step 18.
Fig. 3
5. Reinstall front panel.
6. Remove existing plastic top from dispenser and install
supplied gasket around perimeter of dispenser top
(Fig. 2).
7. Sanitize dispenser before proceeding.
gasket
Fig. 2
Maestro 400 Series Top Kit for Lancer 9
Fig. 5
10. Use pliers to compress and remove cage nut at front
of condenser on ice machine base (Fig. 5.1).
11. Install lter and grille. Lock in place using four
mounting screws (Fig. 5.2).
Fig. 6
Module No.
M
o
d
u
l
e
N
o
.
Product
P
r
o
d
u
c
t
Sto
ck Mo
d
u
le Identification P
l
ate
S
t
o
c
k
M
o
d
u
l
e
I
d
e
n
t
i
f
i
c
a
t
i
o
n
P
l
a
t
e
20
8
2
6
4
2
0
8
2
6
4
Serv
i
c
e
N
o.
S
e
r
v
i
c
e
N
o
.
MI
N.
BR
A
N
C
H
C
IR
C
U
I
T
AM
PAC
I
T
Y
M
I
N
.
B
R
A
N
C
H
C
I
R
C
U
IT
A
M
P
A
C
I
T
Y
D
ESIG
N
PRESSURE HIG
H
SI
D
E
D
E
S
IG
N
P
R
E
S
S
U
R
E
H
IG
H
S
I
D
E
MAX
.
BR
AN
C
H
C
I
R
C
U
IT
F
U
S
E
SI
Z
E
M
A
X
.
B
R
A
N
C
H
C
IR
C
U
I
T
F
U
S
E
S
I
Z
E
AIR OUT
A
I
R
O
U
T
V
OL
T
S
V
O
L
TS
Ea
sto
n
P
e
nns
ylvan
i
a
E
a
s
t
o
n
P
en
n
syl
v
an
i
a
MO
T
OR C
O
MPRESSOR THER
MA
LLY PR
O
T
EC
TED
M
O
T
O
R
C
O
M
P
RE
S
S
O
R
T
H
E
R
M
A
L
L
Y
P
R
O
T
E
C
T
E
D
T
H
E U
SA
T
H
E
U
S
A
M
A
D
E
I
N
M
A
D
E
IN
SINGLE
S
IN
G
L
E
L
OW
S
I
D
E
L
O
W
S
ID
E
CH
ARGE
C
H
A
R
G
E
OZ
O
Z
PSIG
P
S
I
G
C
C
R
R
R
R
PHASE
P
H
A
SE
A
M
P
S
A
M
P
S
HZ
H
Z
PART
NO
PA
R
T
NO
AMPS
A
M
P
S
FUL
L LOAD AMPS
F
U
L
L
L
O
A
D
A
M
P
S
CORPORATIO
N
C
O
R
PO
R
A
T
IO
N
R
EFR
IG
ERANT
R
E
F
R
IG
E
R
A
N
T
SER
IAL NO
S
E
R
I
AL
N
O
MODEL
M
O
D
E
L
A
I
R I
N
A
IR
I
N
U
U
U
U
L
L
L
L
N
SF
N
S
F
1
filter
grille
2
2
Power
A
B
C
Top back view – air-cooled
top mount
3/8" OD
water inlet
Drain
3/4" MPT
12. Make water, drain and electric connections to
ice machine (Fig. 6).
Note: Water connection accepts 3/8" OD
copper or plastic tubing. Push tubing in
until it stops. Use supplied 90˚ push-in
water inlet  tting if there is not enough
clearance behind ice machine to install
water tubing without kinking tubing or
putting stress on  tting.
Note: Follett recommends the installation
of a Follett water  lter system (part#
00130229) on supply water inlet.
10 Maestro 400 Series Top Kit for Lancer
Fig. 7
13. Remove ice machine top panel and louvered side
panel.
14. Insert ice transport tube to a 1/2" (13mm) depth
through mounting bracket (Fig. 7 and 8.1) and
secure transport tube away from condenser fan
under  oat reservoir bracket
(Fig. 8.2).
15. Tighten clamp screw on ice machine base securely
(Fig. 8.3).
16. Uncoil capillary tube from bin thermostat and route
through hole in gasket to mounting bracket and
secure as shown (Fig. 7).
17. Reinstall ice machine louvered side panel and top
panel.
GO TO STARTUP – STEP 27.
ice transport tube
bin thermostat
1/2"
2"
Fig. 8
2
1
3
tighten
clamp
screw
insert ice
transport
tube
Maestro 400 Series Top Kit for Lancer 11
RIDE model ice machine installation
18. Ice transport tube chase may be located behind
or to either side of the dispenser (Fig. 9 and 10).
Using the chase mounting bracket as a template
mark the counter for the ice transport tube(s)
in one of the locations shown in Fig. 9 and 10.
Within the template outline drill one 2.25" (58mm)
to 2.375" (61mm) hole for each ice transport
tube. Secure the chase mounting bracket to the
counter using supplied screws (Fig. 11).
Fig. 9 – Single ice tube dispensers
Fig. 10 – Double ice tube dispensers
2.25" (57 mm) -
2.375" (61 mm)
dia. hole
typical
1.25
(32 mm)
1.25" (32mm)
1.25"
(32 mm)
1.50" (38 mm)
1.50" (38 mm)
front
side entry
chase
side entry
chase
rear entry chase
4.50" (115 mm)
4.50" (11 5mm)
A
B
6"
(153 mm)
2.25" (57mm) -
2.375" (61mm)
dia. hole
typical
1.25
(32mm)
1.25" (32mm)
1.25"
(32mm)
3" (77mm)
3" (77mm)
front
side entry
chase
side entry
chase
rear entry chase
A
B
6"
(153mm)
Fig. 11
Dimension A Dimension B
Single tube – Fig. 9
22" (559mm) dispenser 11.00" (280mm) 8.00" (204mm)
30" (762mm) dispenser 15.00" (381mm) 12.00" (305mm)
Double tube – Fig. 10
22" (559mm) dispenser 9.50" (242mm) 8.00" (204mm)
30" (762mm) dispenser 13.50" (343mm) 12.00" (305mm)
12 Maestro 400 Series Top Kit for Lancer
19. Remove lid from dispenser top (Fig. 12.1). Remove the
knockout from the Harmony top (Fig. 12.2) corresponding to
selected chase location. Line the edges of the opening with
the supplied gasket material (Fig. 12.2).
20. Follow the “RIDE model ice machine installation procedure”
found in the Symphony MCD400 Ice machine Manual
208600 to install your Follett ice machine.
21. Route the bin signal cord from the 4" x 4" (102mm x 102mm)
junction box through the top knockout (Fig. 12.2) and
countertop hole. Attach the bin signal connector to the two
lead plug on the ice machine.
22. Route the ice transport tube(s) from the ice machine (or
evaporator module) through counter cutout and knock out
into dispenser top by following the same routing as the bin
signal cord (Fig. 12.2).
1
1
1
2
2
2
Fig. 12
Maestro 400 Series Top Kit for Lancer 13
23. Connect the ice transport tube(s) to the dispenser:
a) Drill 3/16" (5mm) holes through both sides of the tube
1/2" (13mm) from the tube end.
b) Collapse tube and insert through gasketed hole (Fig. 7).
c) Match tube holes to bracket tabs.
24. Route bin thermostat capillary tube from the 4" x 4"
(102mm x 102mm) junction box into bin alongside the ice
transport tube. Secure capillary tube into bracket (Fig. 7).
25. Reinstall the dispenser cover with supplied screws (Fig. 13).
26. Install telescoping chase (RIDE model ice machines only).
a) Mount lower chase section to chase bracket on counter
with supplied screws (Fig. 14.1).
b) Position upper chase section over lower chase section.
Align top of upper section to top of stainless dispenser top
(Fig. 14.2).
c) Drill pilot holes on both sides of chase and secure with
supplied screws (Fig. 14.3).
27. Turn ice machine power and water on.
28. After ice machine has made ice for approximately 15 minutes
complete the following start-up checks:
a) Dispense ice.
b) Hold ice on bin thermostat and make sure
ice machine shuts off.
c) Remove ice from bin thermostat and make sure
ice machine restarts.
Note: Ice machine has a 20 minute restart delay.
Fig. 13
1
1
2
3
3
1
Fig. 14
14 Maestro 400 Series Top Kit for Lancer
Cleaning/descaling and sanitizing
Periodic cleaning/descaling and sanitizing of Follett’s ice machine system is required to ensure peak
performance and delivery of clean, sanitary ice. The recommended cleaning procedures that follow should be
performed at least as frequently as recommended and more often if environmental conditions dictate.
Cleaning of the condenser can usually be performed by facility personnel. Cleaning/descaling and sanitizing of
the ice machine system should be performed by your facility’s trained maintenance staff or a Follett authorized
service agent. Regardless of who performs the cleaning, it is the operator’s responsibility to see that this
cleaning is performed according to the schedule below. Service problems resulting from lack of preventive
maintenance will not be covered under the Follett warranty.
Symphony Frequency
Drain Line weekly
Drain Pan/Drip Pan weekly
Exterior as needed
Condenser monthly (air-cooled only)
Ice Machine semi-annually
Transport Tube semi-annually
* Ice machine must be cleaned and sanitized prior to start-up.
Weekly
The exterior may be cleaned with a stainless cleaner such as 3M* Stainless Steel Cleaner & Polish or equivalent.
* 3M is a trademark of 3M Company.
Monthly
Condenser (air-cooled ice machine only)
1. Use a vacuum cleaner or stiff brush to carefully clean condenser coils of lint and debris to ensure
optimal performance.
2. When reinstalling counter panels in front of RIDE model ice machines, be sure that ventilation louvers
line up with condenser air duct.
Semi-Annually (more often if conditions dictate)
§ A cleaning/descaling and sanitizing procedure should always include both the ice machine and dispenser; ice
machine should be cleaned and sanitized  rst, followed by the dispenser.
§ Icemaking system can be cleaned/descaled in place.
To ensure that your ice machine and dispenser are cleaned/descaled and sanitized properly, proceed as follows:
1. Clean/descale the ice machine
2. Sanitize the ice machine
3. Clean/descale the dispenser
4. Sanitize the dispenser
CAUTION!
§ Wear rubber gloves and safety goggles (or face shield) when handling cleaner or sanitizer mixtures.
§ Use only Follett approved cleaners.
§ It is a violation of Federal law to use Solution A or Solution B in a manner inconsistent with their labeling.
§ Do not use solvents, abrasive cleaners, metal scrapers or sharp objects to clean any part of the dispenser.
Solution A: Following manufacturer’s instructions, mix cleaning solution of 1 gal. (3.8L) 120 F (49 C) water and
7oz. (198g) (one 7oz. packet) of Follett SafeCLEAN™ ice machine cleaner/descaler (P/N00132001).
Solution B: Following manufacturer’s instructions, mix a sanitizing solution of 1 gal. (3.8L) 120 F (49 C) water and
1.6oz. (48ml) Nu-Calgon IMS-II Sanitizer (P/N 00979674).
Maestro 400 Series Top Kit for Lancer 15
Clean/descale ice machine
1. If ice machine was running recently, ensure that the evaporator is completely free of ice before proceeding.
2. Disconnect power to ice machine.
3. Remove any ice machine panels required to gain access to water reservoir and electrical control box.
4. Turn compressor switch on electrical box of ice machine to OFF position.
5. Remove water reservoir cover and close water supply valve (or block up reservoir  oat).
6. Drain water from reservoir by releasing evaporator drain tube from  oat reservoir bracket, removing plug
from drain tube and releasing (unclamping) pinch clamp (if equipped).
7. Plug drain hose, replace drain line in reservoir bracket and pour part of Solution A into reservoir,  lling it
almost to over owing.
8. Remove stainless steel ice compression nozzle and drain lines and submerge in a cup of SolutionA while
cleaning/descaling rest of system. (Flake ice machines have no ice compression nozzle and drain lines.)
CAUTION: To avoid potential pitting, do not soak parts in SolutionA for more than 45 minutes.
9. Restore power to ice machine (gearmotor will run; compressor and fan will not).
10. Inspect evaporator drain pan and drain line and remove any accumulated scale build up.
11. After 15 minutes, turn power OFF; drain solution from reservoir and evaporator.
12. Fill reservoir almost to over owing with clean water to rinse. Drain. Repeat two more times.
13. Rinse ice compression nozzle and drain lines in clean water.
Sanitize ice machine
14. Submerge ice compression nozzle and drain lines in a cup of Solution B while following steps 15-21.
15. Connect ice transport tube directly onto evaporator outlet port without ice compression nozzle.
16. Fill reservoir almost to over owing with Solution B.
17. Restore power to ice machine (gearmotor will run; compressor and fan will not).
18. After 10 minutes, turn compressor switch to ON position.
19. As unit starts to make ice, continue to pour Solution B into reservoir, maintaining level just below reservoir
over ow.
20. Continue to make ice with Solution B for 20 minutes.
21. Turn power to ice machine OFF.
22. Disconnect ice transport tube from evaporator outlet port. Rinse ice compression nozzle and drain lines in
clean water and reinstall on evaporator outlet. Reconnect ice transport tube to ice compression nozzle.
23. Drain any remaining Solution B from evaporator.
24. Fill reservoir almost to over owing with 120 F (49 C) clean water to rinse. Drain. Repeat two more times. Re-
clamp pinch clamp, replace drain plug, and re-secure drain tube ensuring that end of drain tube is above
water level in reservoir.
25. Open water supply valve (or unblock  oat) and replace reservoir cover; restore power to ice machine
and ensure compressor switch is in ON position. Make ice for at least 15 minutes to  ush any remaining
Solution B from system (RIDE ice machines with long ice transport hoses may take longer to  ush out).
Discard this ice and all ice made during sanitizing.
26. Reinstall all parts and replace any panels removed prior to cleaning.
16 Maestro 400 Series Top Kit for Lancer
Stock Module Identifi
cation Plate
S
ervice No.
20826
4
Pr
o
duct
Module No.
E
asto
n
Pe
n
ns
ylv
an
i
a
VO
L
TS
M
O
T
OR COM
P
R
ESSOR
T
HER
MAL
L
Y P
ROTECT
ED
M
A
X
.
B
R
A
NC
H
C
IR
C
U
I
T F
U
SE
S
IZ
E
M
I
N
.
B
R
AN
C
H
C
IR
CU
I
T
A
M
PA
C
I
T
Y
D
E
SI
G
N
PR
E
SSU
R
E HIGH
S
I
DE
HZ
P
A
R
T
NO
A
M
PS
CHAR
G
E
PS
I
G
O
Z
T
H
E
U
S
A
M
A
D
E IN
R
C
LO
W
S
IDE
R
P
H
A
S
E
S
I
NGL
E
AMPS
S
E
RI
AL
NO
MODE
L
FU
L
L
L
OA
D
AMP
S
C
O
RPORA
TI
O
N
REFRIGE
R
A
N
T
L
U
NSF
U
L
13
10
7
9
12
14
Reference # Description Part #
1 Base, top mount 00113514
1 Base, RIDE model 00113308
2 Cabinet 00113324
3 Cover 00113357
4 Chase, upper 00113381
5 Chase, lower 00113399
6 Collar 00113407
7 De ector, single 501616
8 Box, thermostat 00113449
9 Gasket, top, Harmony 00113464
10 Gasket, ice entry 502824
11 Socket, bin signal 502334
12 Kit, ice entry, MCD400 00120279
13 Plate, ice tube mounting, MCD400 307071
14 Lid, access 00113431
Not shown Thermostat, bin level 500514
Not shown Plate, blank, ice entry 00113498
8
2
4
3
11
10
1
5
6
7
14
Service
Replacement parts
Models MTL22SC and MSL22SC
Order parts online
www.follettice.com
Maestro 400 Series Top Kit for Lancer 17
Models MTL30SC and MSL30SC
Reference # Description Part #
1 Base, top mount 00113522
1 Base, RIDE model 00113316
2 Cabinet 00113332
3 Cover 00113365
4 Chase, upper 00113381
5 Chase, lower 00113399
6 Collar 00113407
7 De ector, single 501616
8 Box, thermostat 00113449
9 Gasket, top, Harmony 00113464
10 Gasket, ice entry 502824
11 Socket, bin signal 502334
12 Kit, ice entry, MCD400 00120279
13 Plate, ice tube mounting, MCD400 307071
14 Lid, access 00113431
Not shown Thermostat, bin level 500514
Not shown Plate, blank, ice entry 00113498
Order parts online
www.follettice.com
St
o
c
k
Mod
u
l
e
Ide
nti
f
ic
a
t
i
o
n
P
l
ate
S
e
rvi
ce
N
o.
2
08264
P
r
o
d
u
ct
Mo
d
ule
No.
CORPORA
T
IO
N
S
ERIAL NO
C
H
A
R
G
E
PS
I
G
M
O
TOR CO
MPRES
S
O
R
T
HE
RM
AL
L
Y
PR
O
T
E
CTE
D
VOLTS
DE
SIGN
P
RES
S
U
RE
HIGH
S
IDE
M
A
X.
B
R
A
N
C
H
C
I
R
C
U
IT F
U
SE S
I
Z
E
M
I
N
.
B
RANC
H
C
IR
C
U
I
T
AM
P
AC
I
TY
A
MPS
A
MPS
R
C
T
H
E
U
S
A
MAD
E IN
L
OW SIDE
R
M
ODEL
F
U
LL
LOA
D
A
M
PS
REF
R
I
G
ERANT
E
a
s
t
on
Pe
nn
sy
lva
n
i
a
HZ
P
A
R
T
NO
OZ
PHA
SE
SING
L
E
L
U
NSF
U
L
13
10
7
9
12
14
8
2
4
3
11
10
1
7
5
6
9
14
18 Maestro 400 Series Top Kit for Lancer
Water treatment accessories for Symphony ice and water dispensers
Reference # Description Part #
Standard capacity  lter system
Not shown Follett QC4-FL4S water  lter system (includes FL4S primary cartridge and head, coarse
pre- lter and head, pressure gauge,  ushing valve; assembled and installed on mounting
bracket), one per ice machine
00130229
Not shown Follett FL4S primary replacement cartridge 00130245
Not shown Water  lter cartridge – primary, carton of 6 00954297
Not shown Everpure coarse pre- lter cartridge 00130211
Not shown Water pre- lter cartridge – pre- lter, carton of 12 00954305
High capacity  lter system
Not shown High capacity water  lter system (one per ice machine) 00978957
Not shown High capacity water  lter cartridge – primary, single 00978965
Not shown High capacity water  lter cartridge – primary, carton of 6 00978973
Not shown Water pre- lter cartridge – pre- lter, single 00130211
Not shown Water pre- lter cartridge – pre- lter, carton of 12 00954305
Carbonless high capacity  lter system
Not shown Carbonless high capacity water  lter system (one per ice machine) – Horizon and Maestro
series ice machines
01050442
Not shown Carbonless high capacity water  lter cartridge – primary, single 01050426
Not shown Carbonless high capacity water  lter cartridge – primary, carton of 6 01050434
Not shown Water pre- lter cartridge – pre- lter, single 00130211
Not shown Water pre- lter cartridge – pre- lter, carton of 12 00954305
Other  ltration
Not shown Claris hardness removal  ltration system 00986059
Not shown Replacement  lter for Claris system 00985127
Not shown Reverse osmosis system, 200 gallons per day 00986034
Not shown Replacement reverse osmosis cartridge 00985085
Not shown Replacement reverse osmosis pre- lter 00985077
Not shown Cleaning plug for reverse osmosis system 00985119
Not shown Cleaning cartridge for reverse osmosis system 00985101
Water pressure
Not shown Water pressure regulator (25 psi) 501781
Maestro 400 Series Top Kit for Lancer 19
This page intentionally left blank.
00117267R04
© Follett Corporation 2/14
801 Church Lane • Easton, PA 18040, USA
Toll free (877) 612-5086 • (610) 252-7301
www.follettice.com
Harmony, Maestro, and SafeCLEAN are trademarks of Follett Corporation.
Chewblet, RIDE and Follett are registered trademarks of Follett Corporation, registered in the US.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20

Follett Maestro Chewblet 400 Series Installation, Operation And Service Manual

Follett
Brand
Follett
Model
Maestro Chewblet 400 Series
Category
Ice cube makers
Type
Installation, Operation And Service Manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents