JetCon 2401 Industrial Serial to Fiber Media Converter
Quick Installation Guide V1.3
A Beijer Electronics Group Company
the serial communication infrastructure and link more JetCon 2401. To ensure the quality of
serial line signal, JetCon 2401 provides 2 termination resistors for the RS-422/485 TX and
RX signal by DIP switch enabled/Disable. About the DIP Switch setting, please refer to DIP
Switch setting table.e following information will show the dierent serial signal
connectivities for your reference.
Data+
Data-
GND
Data+
Data-
GND
Data+
Data-
GND
Data+
Data-
GND
T+
T-
R+/D+
R-/D-
TX
RX
GND
Serial to Fiber Media Converter
2401
PWR
TX
RX
Ring
RX TX
V+
V-
RS-422/485 RS-232 12-48V
T+
T-
R+/D+
R-/D-
TX
RX
GND
Serial to Fiber Media Converter
2401
PWR
TX
RX
Ring
RX TX
V+
V-
RS-422/485 RS-232 12-48V
JetCon 2401JetCon 2401
RX
TX
TX
RX
Fiber
PC with 2-wires RS-485 RS-485 serial Mode RS-485/2 wires serial Mode Device with 2-wires
RS-485 serial
TX+
TX-
RX+
RX-
GND
RX+
RX-
TX+
TX-
GND
TX+
TX-
RX+
RX-
GND
RX+
RX-
TX+
TX-
GND
PC with 4-wires
RS-422/485
RS-422/485 4-wires
serial Mode
RS-422/485 4-wires
serial Mode
Device with 4-wires
RS-422/485 serial
T+
T-
R+/D+
R-/D-
TX
RX
GND
Serial to Fiber Media Converter
2401
PWR
TX
RX
Ring
RX TX
V+
V-
RS-422/485 RS-232 12-48V
T+
T-
R+/D+
R-/D-
TX
RX
GND
Serial to Fiber Media Converter
2401
PWR
TX
RX
Ring
RX TX
V+
V-
RS-422/485 RS-232 12-48V
JetCon 2401JetCon 2401
RX
TX
TX
RX
Fiber
Data+
Data-
GND
T+
T-
R+/D+
R-/D-
TX
RX
GND
Serial to Fiber Media Converter
2401
PWR
TX
RX
Ring
RX TX
V+
V-
RS-422/485 RS-232 12-48V
T+
T-
R+/D+
R-/D-
TX
RX
GND
Serial to Fiber Media Converter
2401
PWR
TX
RX
Ring
RX TX
V+
V-
RS-422/485 RS-232 12-48V
DTR
DSR
RTS
CTS
RX
TX
GND
TX
RX
GND
Data+
Data-
GND
JetCon 2401JetCon 2401
RX
TX
TX
RX
Fiber
PC with RS-232 serial Device with 2-wires
RS-485 serial
RS-485/2 wires serial ModeRS-232 serial Mode
T+
T-
R+/D+
R-/D-
TX
RX
GND
Serial to Fiber Media Converter
2401
PWR
TX
RX
Ring
RX TX
V+
V-
RS-422/485 RS-232 12-48V
DTR
DSR
RTS
CTS
RX
TX
GND
T+
T-
R+/D+
R-/D-
TX
RX
GND
Serial to Fiber Media Converter
2401
PWR
TX
RX
Ring
RX TX
V+
V-
RS-422/485 RS-232 12-48V
DTR
DSR
RTS
CTS
RX
TX
GND
TX
RX
GND
TX
RX
GND
PC with RS-232 serial RS-232 serial ModeRS-232 serial Mode Device with RS-232 serial
JetCon 2401JetCon 2401
RX
TX
TX
RX
Fiber
Connecting the Optical Fiber
e Fiber Optical link architecture supports PTP and SFR
mode for dierent purposes.
1. PTP Mode (Peer to Peer)
e PTP (Peer to Peer) mode provides connection between
2 nodes. When working on this mode, JetCon 2401 can
transmit data and receive it at same time, which means
JetCon 2401 is working at full duplex mode.
2. SFR Mode (Serial Fiber Ring)
To extend the transmission distance and to save
the ber cable cost, JetCon 2401can link to each
other as a ring architecture, in this mode JetCon
2401 only provides half duplex transmission and
all of data communication is controlled by the
host device. e maximum of communication
nodes can up to 20.
40km
5KM
Modul Fiber (um) Connecter Wavelength(um)
TXPwr
(Min)
TxPwr
(Max)
RxPwr
(Min)
RxPwr
(Max)
LinkBudg(dBm) Distance(km)
JetCon
2401-S
Single-mode
8~10/125
ST 1310nm -9dBm -8dBm -27dBm N/A 18dBm
JetCon
2401-m
Multi-mode
50~62.5/125
ST 820nm -12dBm -9dBm -28dBm N/A 16dBm
The table below illustrates fiber transceiver specifications
TxPwr(Min):Minimum Launch Power TxPwr(Max):Maximum Launch Power
RxPwr(Min):Maximum Receive Sensitivity RxPwr(Max):Minimum Receive Sensitivity
Link Budget=Minimum Launch Power -Maximum Receive Sensitivity
Note: To ensure your ber converter transmission/receiving of data between the 2
nodes, the attenuation of the optical ber cable should be smaller than the ber
converter's Link Budget.
JetCon 2401 DIP Switch Setting
RS-232
RS-485/2 wires
RS-485/4 wires
RS-422/4 wires (Default)
NO
Function DIP Switch 2
OFF
ON
OFF
OFF (Default)
DIP Switch 1
ON
OFF
OFF
OFF (Default)
Point to Point /Serial Ring
120 Ohm Terminator (TX)
120 Ohm Terminator (RX)
Function Switch position
Off (PTP)/On (SFR ), Default off (PTP)
Off (Disable)/On (Enable), Default off
Off (Disable)/On (Enable), Default off
DIP Switch
Switch 5
Switch 4
Switch 3
Note: After adjusting the DIP-switch, please reboot the unit to activate the new settings.
RS422/485RS232
PTP Mode
SFR Mode
Half Duplex
RS232/422/485
RS422/485
RS422/485
JetCon 2401
Overview
JetCon 2401 is a Multi-serial to ber media converter which has RS-232/RS-422/RS-485
triple mode circuits with auto baud rate and direction control functions. It extends the
distance of serial communication to 5KM (JetCon 2401-m Multi-mode Optical Fiber) or
40KM (JetCon 2401-s Single-mode Optical Fiber) and also provides good immunity of
EMI/EMS. For the ESD protection, JetCon 2401 also passed the 15KV ESD testing on serial
line.
To ensure nonstop transmission in hazardous environment, JetCon 2401 supports wide
operating temperature range, -20~70
o
C model (JetCon 2401) and -40~70
o
C model (JetCon
2401-w). Further more, JetCon 2401 supports wide range power input (DC/AC) and DIN
rail mount for quick and easy installation.
Package Check List
JetCon 2401 Industrial serial to ber media Converter
Quick Installation Guide
DIN rail mount kits
Overview
JetCon 2401 is a Multi-serial to fiber media converter which has RS-232/
RS-422/RS-485 triple mode circuits with auto baud rate and direction control
functions. It extends the distance of serial communication to 5KM (JetCon
2401-m Multi-mode Optical Fiber) or 40KM (JetCon 2401-s Single-mode Optical
Fiber) and also provides good immunity of EMI/EMS. For the ESD protection,
JetCon 2401 also passed the 15KV ESD testing on serial line.
To ensure nonstop transmission in hazardous environment, JetCon 2401
supports wide operating temperature range, -20~70
o
C model (JetCon 2401) and
-40~70
o
C model (JetCon 2401-w). Further more, JetCon 2401 supports wide
range power input (DC/AC) and DIN rail mount for quick and easy installation.
JetCon 2401 Industrial Serial to Fiber Media Converter
Quick Installation Guide V1.3
A Beijer Electronics Group Company
Package Check List
Unpack the box, you will find
JetCon 2401 Industrial serial to fiber
media Converter
Quick Installation Guide
DIN rail mount kits
Overview
JetCon 2401 is a Multi-serial to fiber media converter which has RS-232/
RS-422/RS-485 triple mode circuits with auto baud rate and direction control
functions. It extends the distance of serial communication to 5KM (JetCon 2401-m
Multi-mode Optical Fiber) or 40KM (JetCon 2401-s Single-mode Optical Fiber)
and also provides good immunity of EMI/EMS. For the ESD protection, JetCon
2401 also passed the 15KV ESD testing on serial line.
To ensure nonstop transmission in hazardous environment, JetCon 2401 supports
wide operating temperature range, -20~70
o
C model (JetCon 2401) and -40~70
o
C
model (JetCon 2401-w). Further more, JetCon 2401 supports wide range power
input (DC/AC) and DIN rail mount for quick and easy installation.
JetCon 2401 Industrial Serial to Fiber Media Converter
Quick Installation Guide V1.3
A Beijer Electronics Group Company
Package Check List
Unpack the box, you will find
JetCon 2401 Industrial serial to fiber
media Converter
Quick Installation Guide
DIN rail mount kits
Installation
Mounting the Unit
Din-Rail mount: screw up the DIN rail mount kit with 4 screws and mount JetCon
2401 on the DIN Rail.
Earth Ground
T+
T-
R+/D+
R-/D-
TX
RX
GND
Serial to Fiber Media Converter
2401
PWR
TX
RX
Ring
RX TX
V+
V-
RS-422/485 RS-232 12-48V
V+ V- GND
Accept 24AWG wire.
Grounding JetCon 2401
ere is one earth grounding pole include in power-input
connector. Connect the earth grounding of JetCon 2401
which is within power-input terminal block to ensure
system safety and prevent noise to interfere communication.
Wiring the Power Inputs
1. Insert the positive and negative wires into the V+ and V-
contact on the terminal block connector.
2. Tighten the wire-clamp screws to prevent the power wires
from being loosened.
Notes: e recommended working voltage is DC24V
(DC12~ 48 V) or AC24V (AC 12~32V) with polarity
reverse protection.
Connecting to serial line
e JetCon 2401 provides triple mode circuits for RS-232/RS-422/RS-485 2/4-wires and
extend these signals to 5KM or 40KM by optical ber cable.e converter operating
architecture can also congure as a PTP (Peer to Peer) or SFR (Serial Fiber Ring) to enlarge
5 Years Warranty
Each of Korenix’s product line is designed, produced, and tested with high industrial
standard. Korenix warrants that the Product(s) shall be free from defects in materials and
workmanship for a period of ve (5) years from the date of delivery provided that the
Product was properly installed and used.
is warranty is voided if defects, malfunctions or failures of the warranted Product are
caused by damage resulting from force measure (such as oods, re, etc.), other external
forces such as power disturbances, over spec power input, or incorrect cabling; or the
warranted Product is misused, abused, or operated, altered and repaired in an unauthorized
or improper way.
Attention! To avoid system damage caused by sparks, please DO NOT plug in power
connector when power is on.
e product is in compliance with Directive 2002/95/EC and 2011/65/EU of the European
Parliament and of the Council of 27 January 2003 on the restriction of the use of certain
hazardous substances in electrical and electronics equipment(RoHS Directives & RoHS 2.0)
Support
Korenix Customer Service
KoreCARE is Korenix Technology's global service center, where our professional stas are
ready to solve your problems at any time Korenix global service center's e-mail is
For more information and documents download please visit our website:
http://www.korenix.com/downloads.htm
Patent No. (Taiwan):
Granted Invention: I 313547
Granted Invention: I 321415
Granted Invention: I 344766
Granted Invention: I 346480
Granted Invention: I 356616
Granted Invention: I 364684
Granted Invention: I 376118
Granted Invention: I 393317
Granted Invention: I 398066
Granted Invention: I 398125
Utility Model: M 339841
Utility Model: M 339840
Tel:+886-2-89111000
Fax:+886-2-29123328
Business service:[email protected]
Customer service:[email protected]
www.korenix.com
CPQ000V2401003
Korenix Technology Co., Ltd.
(A Beijer Electronics Group Company)
⪺墾
JetCon 2401㘖ᷧ㬥ᷰ⏯ᷧḙ⏊当ℰ事Ὲ⏞当㍉♏˛ JetCon 2401㔖㋨RS-232/RS-422/
RS-485⤁䦴ḙ⏊䔳杉Ə㔖㋨凑忩怆䍮⎱㕗㍕㴨⏸凑⊏㎎∝˛ JetCon 2401⯭ḙ堳Ὲ
⏞当㍉ㇷℰ事Ὲ⏞Ə ḙ堳Ὲ⏞䙫ἇ彺巄䦢㉐⤎∗5KM (JetCon 2401-m ⤁㨈ℰ事)ㇽ
40KM (JetCon 2401-s ⌼㨈ℰ事)Ə ⹝⅞㛰⽯⼡䙫㉾EMI/EMS䔜䢨⹙㉗䙫䉠『˛
JetCon 2401徿忶微ṭḙ⏊15KV ESD㵑㵳ῄ㊋㴲宼˛
ḡṭῄ宨✏そ⊊䎖⡪ᷲ㕗㍕态宖䙫⏖杇『ƏJetCon 2401 㔖㋨⮤㸐䙫ⷌὃ㸐⺍
-20~70
o
C (JetCon 2401) Əㇽ俬Ō-40~70
o
C (JetCon 2401-w)˛ 㭋⣽ƏJetCon 2401徿㔖
㋨彪⮤䙫(DC/AC)䔜㹷彺⅌勪⛛Ə⎱ᷰ䦴⭰墬㨈Ə㠳杉Ə⢨㋩⑳⯣彏⭰墬˛
ᵥ⍿㳃∓
JetCon 2401 ⷌḁ于ḙ⏊当ℰ事Ὲ⏞当㍉♏
⿒怆⭰墬⏸⯣
⯣彏⭰墬愴ờ
⩇垃
⩇垃怋ᶴ
⯣彏⭰墬: 䔏4桾垡Ḅ⯭JetCon 2401䙫倚俣⛡⮁✏⢀ᷱ˛
JetCon 2401㉣◮
✏JetCon 2401䙫䔜㹷彺⅌䫖⬷⣫㛰ᷧḑ✗亦㎌✗䫖⬷˛⯭
JetCon 2401䙫䔜㹷㎌亦䫖⬷Ḕ䙫✗亦㎌✗Əὦ宥⣮ℴ⎾♑⣗
⹙㉗˛宥⣮㜑㎌✗Ə⛇凑䄝⛇䴇怇ㇷ㍆⮚Ə⯭ᷴṯỌ⣴˛
Overview
JetCon 2401 is a Multi-serial to fiber media converter which has RS-232/
RS-422/RS-485 triple mode circuits with auto baud rate and direction control
functions. It extends the distance of serial communication to 5KM (JetCon
2401-m Multi-mode Optical Fiber) or 40KM (JetCon 2401-s Single-mode Optical
Fiber) and also provides good immunity of EMI/EMS. For the ESD protection,
JetCon 2401 also passed the 15KV ESD testing on serial line.
To ensure nonstop transmission in hazardous environment, JetCon 2401
supports wide operating temperature range, -20~70
o
C model (JetCon 2401) and
-40~70
o
C model (JetCon 2401-w). Further more, JetCon 2401 supports wide
range power input (DC/AC) and DIN rail mount for quick and easy installation.
JetCon 2401 Industrial Serial to Fiber Media Converter
Quick Installation Guide V1.3
A Beijer Electronics Group Company
Package Check List
Unpack the box, you will find
JetCon 2401 Industrial serial to fiber
media Converter
Quick Installation Guide
DIN rail mount kits
Earth Ground
T+
T-
R+/D+
R-/D-
TX
RX
GND
Serial to Fiber Media Converter
2401
PWR
TX
RX
Ring
RX TX
V+
V-
RS-422/485 RS-232 12-48V
府㉣䏳㵎䵽
1. ⯭䔜㹷䙫㭊崆㝨㎌⅌䔜㹷㎌亦䫖⬷䙫V+ ⑳ V- ㎌⤛˛
2. ㋎䴎垡ḄƏ昙㭉䔜㹷亦儘吤˛
㳏ヶŌJetCon 2401䙫ⷌὃ䔜⍲㘖DC24V (DC12~48 V)
ㇽ俬 AC24V (AC 12~32V) Ə⹝⅞⣮㭊崆㝨『⎴㎌ῄ㊋˛
府㉣ᳰ⊡
JetCon 2401 ㎷ᾂ⤁䦴ḙ⏊态宖㨈Ə⋬㋓RS-232/RS-422/RS-485 2/4-wiresƏ⯭ḙ堳
Ὲ⏞忶微ℰ事⯭态宖巄䦢⻝敦∗5KM ㇽ 40KM˛当㍉♏䙫㒴ὃ㨈徿⏖Ọ宥何ḡ
PTP (Peer to Peer) ㇽ俬SFR (Serial Fiber Ring) 㨈Ə⏖㉐⤎ḙ堳态宖䙫奭䚽杉䧖必㎌
㛛⤁䙫JetCon 2401˛
ḡῄ暃ḙ堳Ὲ⏞态宖崏憶ƏJetCon 2401ḡRS-422/485䙫TX⑳RX䫖㎷ᾂ2ḑ亯䫖䔜昢
Ə⏖忶微Dip㋏䟨⻧⅚富䔜昢˛⅚ṵDIP㋏䟨⻧⅚䙫宥何Ə寞⎩䛲DIP Switch宥⮁塏
˛ᷲ杉䙫⛥䤡Əḡ⤎⮝⇾⇡ᷴ⏳䙫ḙ⏊Ὲ⏞亦必㎌㨈˛
V+ V- GND
Accept 24AWG wire.
T+
T-
R+/D+
R-/D-
TX
RX
GND
Serial to Fiber Media Converter
2401
PWR
TX
RX
Ring
RX TX
V+
V-
RS-422/485 RS-232 12-48V
DTR
DSR
RTS
CTS
RX
TX
GND
T+
T-
R+/D+
R-/D-
TX
RX
GND
Serial to Fiber Media Converter
2401
PWR
TX
RX
Ring
RX TX
V+
V-
RS-422/485 RS-232 12-48V
DTR
DSR
RTS
CTS
RX
TX
GND
TX
RX
GND
TX
RX
GND
PC with RS-232 serial RS-232 serial ModeRS-232 serial Mode Device with RS-232 serial
JetCon 2401JetCon 2401
RX
TX
TX
RX
Fiber
TX+
TX-
RX+
RX-
GND
RX+
RX-
TX+
TX-
GND
TX+
TX-
RX+
RX-
GND
RX+
RX-
TX+
TX-
GND
PC with 4-wires
RS-422/485
RS-422/485 4-wires
serial Mode
RS-422/485 4-wires
serial Mode
Device with 4-wires
RS-422/485 serial
T+
T-
R+/D+
R-/D-
TX
RX
GND
Serial to Fiber Media Converter
2401
PWR
TX
RX
Ring
RX TX
V+
V-
RS-422/485 RS-232 12-48V
T+
T-
R+/D+
R-/D-
TX
RX
GND
Serial to Fiber Media Converter
2401
PWR
TX
RX
Ring
RX TX
V+
V-
RS-422/485 RS-232 12-48V
JetCon 2401JetCon 2401
RX
TX
TX
RX
Fiber
Data+
Data-
GND
T+
T-
R+/D+
R-/D-
TX
RX
GND
Serial to Fiber Media Converter
2401
PWR
TX
RX
Ring
RX TX
V+
V-
RS-422/485 RS-232 12-48V
T+
T-
R+/D+
R-/D-
TX
RX
GND
Serial to Fiber Media Converter
2401
PWR
TX
RX
Ring
RX TX
V+
V-
RS-422/485 RS-232 12-48V
DTR
DSR
RTS
CTS
RX
TX
GND
TX
RX
GND
Data+
Data-
GND
JetCon 2401JetCon 2401
RX
TX
TX
RX
Fiber
PC with RS-232 serial Device with 2-wires
RS-485 serial
RS-485/2 wires serial ModeRS-232 serial Mode
Data+
Data-
GND
Data+
Data-
GND
Data+
Data-
GND
Data+
Data-
GND
T+
T-
R+/D+
R-/D-
TX
RX
GND
Serial to Fiber Media Converter
2401
PWR
TX
RX
Ring
RX TX
V+
V-
RS-422/485 RS-232 12-48V
T+
T-
R+/D+
R-/D-
TX
RX
GND
Serial to Fiber Media Converter
2401
PWR
TX
RX
Ring
RX TX
V+
V-
RS-422/485 RS-232 12-48V
JetCon 2401JetCon 2401
RX
TX
TX
RX
Fiber
PC with 2-wires RS-485 RS-485 serial Mode RS-485/2 wires serial Mode Device with 2-wires
RS-485 serial
2. SFR Mode (Serial Fiber Ring)
ḡṭ㉐⤎ἇ彺巄䦢Ə⹝奨剩䛨亦㜷ㇷ㜓Ə
JetCon 2401⏖Ọ必㎌ㇷᷧḑ䎖䱢㞝㝫˛✏忀
䦴㨈ᷲƏJetCon 2401⏑㔖㋨⌱⎳ⷌἇ彺㨈
Ə俳᷻㕗㍕ἇ彺惤曧奨忶微Ḣ㜡奨㎎∝˛
富㨈㔖㋨䙫㛧⤎剩䂠㕗㘖20ḑ˛
TxPwr(Min):Minimum Launch Power TxPwr(Max):Maximum Launch Power
RxPwr(Min):Maximum Receive Sensitivity RxPwr(Max):Minimum Receive Sensitivity
Link Budget=Minimum Launch Power -Maximum Receive Sensitivity
府㉣ 䵢⊡
ℰ事必㎌㔖㋨PTP ⑳SFRḋ䦴㨈㻈嶚ᷴ⏳曧㰩˛
1. PTP Mode (Peer to Peer)
同德PTP (Peer to Peer)㨈䙫当㍉♏Ə㔖㋨䂠∗䂠䙫必㎌
㨈˛忀㠞JetCon 2401㔖㋨⏳㗝⎸忨⑳㎌㔝㕗㍕Ə忀ヶ
䜧JetCon 2401⏖Ọ✏⅏⎳ⷌ㨈ᷲⷌὃ˛
圦⃕㓌ᵄ 䵢㏴⊏┦䕂墂㛺
RS422/485RS232
PTP Mode
SFR Mode
Half Duplex
RS232/422/485
RS422/485
RS422/485
JetCon 2401
40km
5KM
Modul Fiber (um) Connecter Wavelength(um)
TXPwr
(Min)
TxPwr
(Max)
RxPwr
(Min)
RxPwr
(Max)
LinkBudg(dBm) Distance(km)
JetCon
2401-S
Single-mode
8~10/125
ST 1310nm -9dBm -8dBm -27dBm N/A 18dBm
JetCon
2401-m
Multi-mode
50~62.5/125
ST 820nm -12dBm -9dBm -28dBm N/A 16dBm
㮦⿍媵↽ᵌ䏳㵎ⶾ⋭㒴㊐㆒㉣䵽䦭⨎濕ᶣ弽ᵥ䏝㼩兯廞ノ䮹䶝㈝☍Ʋ
㭋Ẏ⒨ῄ宨⭳⅏䬍⏯㬎䛆2003⹛1㛯27㗌䔜㯻⑳䔜⬷宥⣮⍘⮚䉐崏昷∝⦻ἁ㈧㎷
⇡䙫昷䔏㋮ị2002/95/EC(ROHS䥨ị)⎱2011/65/EU(RoHS 2.0)˛
Korenix
⏬⋌㗋⅟
KoreCARE 㘖䦸㴂䏭〄䦸㉧⅏䏪㛴⊈Ḕ⾪Əㇸồ᷺ḁ䙫㉧㜖ạ晶㗝↭⣮姊䬻わ䙫
䕸旕˛䦸㴂䏭〄⅏䏪㛴⊈Ḕ⾪ EMAIL: [email protected]
寍亭寛㗵⎱㕮ờ寞凚伸䫀ᷲ彤: http://www.korenix.com.cn/support_downloads.htm
ḁ⊈㛴⊈: [email protected]
⭿伸: www.korenix.com.cn
㳏ヶḡṭ䡕ῄℰ事当㍉♏僤⤆✏ḋḑ剩䂠Ḳ旛㭊⸟㔝⎸㕗㍕Əℰ事亦㜷䙫Ὲ⏞塗
↶曧奨㮻当㍉♏䙫⮁Ḱ䙫塗↶㛛⯶˛
JetCon 2401 DIP Switch婼丬
㳏ヶ: 寪㕛DIP-switchỌ⏵Ə曧奨憴␖宥⣮ὦ宥何䔆㔯˛
5ⴲ實ẛ
㈧㛰䦸㴂䏭〄Ẏ⒨䙫宥守˚∝怇⎱㴲宼惤㘖憮䔏彪檿䙫ⷌḁ㟮↭˛䦸㴂䏭〄ῄ宨
凑Ẏ⒨⇡崎㗌嵞㎷ᾂ㛧檿5 ⹛Ḳℴ崠ῄ㛴⊈Əῄ㜆旛⥩⛇曝ờ㍆✶ㇽ∝䧲ᷴ
剖俳⯣凛Ẏ⒨㔬暃Əㇸồ⯭㎷ᾂℴ崠仛㛴⊈˛
䄝俳Ə凑䄝⣽⊂(䁒˚㰛˚曞䁥)㈧怇ㇷ䙫Ẏ⒨㔬暃Əㇽ⅝⭪⣽惏⛇䴇⥩䔜㹷⹙㉗˚
ᷴ⼺䔜㹷彺⅌˚ᷴ⼺㎌亦䬰怇ㇷ䙫㍆✶Əᷴ⇾⅌Ẏ⒨ῄ⛡勪⛛ƞ㭋⣽ƏẎ⒨墒寖
䔏˚㜑亶㍯㜪䙫䏭⎱㔠䬰堳ḡ⯭怇ㇷῄ⛡㝈㬥⤘㔯˛
⩠ヵ㗋⅟
RS-232
RS-485/2 wires
RS-485/4 wires
RS-422/4 wires (Default)
NO
Function DIP Switch 2
OFF
ON
OFF
OFF (Default)
DIP Switch 1
ON
OFF
OFF
OFF (Default)
Point to Point /Serial Ring
120 Ohm Terminator (TX)
120 Ohm Terminator (RX)
Function Switch position
Off (PTP)/On (SFR ), Default off (PTP)
Off (Disable)/On (Enable), Default off
Off (Disable)/On (Enable), Default off
DIP Switch
Switch 5
Switch 4
Switch 3
/
