Rev. A1
- 1 -
- 4 -
FFAS0911-602500BF0
Single Lever Exposed B&S Mixer
FFAS0912-702500BF0
Single Lever Exposed Shower Only
FFAS0911-602500BF0
FFAS0912-702500BF0
Installation &
Operation Instructions
* Recommended water pressure condition: 0.1~0.5Mpa.
* Environment Temperature:1~55℃
* Steam is not allowed to use.
* The cold and hot water pipes must not be reserved.
Conditions for use
* Remove all impurity in pipes before beginning to avoid clogging. Connect faucet pipes correctly.
* Check installation distances in the Dimension diagram to ensure correct installation.
Make sure the cold water hose is connected to the right side and the hot water hose to the left.
When in the process of installation, grab the whole body. Do not grab handle only.
Pre-Installation Checks
* American Standard always keep raising and improving the product design and performance, and reserve the right to modify
the dimension and spefication. At this case, we will not inform you separately.
* This installation instruction sheet is for your reference only, the dimension and specification is subject to the actual products.
Thank you for selecting American-Standard - the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin.
All instruction procedures must comply in strict accordance with applicable local plumbing and building codes
Recommended Tools and Materials
Electric drill
Pencil
windtight swathe
Adjustable Wrench
Level
Tape Measure
Screwdriver
Sinker
Dimension
Unit: mm
Care & Maintenance
Attention:
Please leave the manual with the customer
after installation is finished.
Trouble Shooting Guide
Untwist the hose.
Cartridge packing
Hose junction
Check the connection.
Check cartridge install.
Check valve position.
Check any impurities.
Remove all impurities.
Open it to full valve
When packing is damaged, replace the cartridge.
Check the existence of packing and wind it up sufficiently
Poor flow rate
Leakage
Water supply valve
Flexible hose
Aerator
Check if hose is twisted.
Check if the water from Supply valve is enough or not
Check if the supply pipe connected correct or not
Connect the hot and cold water pipe correctly
Increase water supply
Deviant
Temperature
Supply Valve
Trouble
Checkpoint
Contents
Action
Supply system
1
2
Test / Usage
* Move handle down into “OFF”position. Turn on supply angle valve to check all connections for leak.
* Operate handle up and down, left and right to flush water lines thoroughly.
Test
Usage
* If you want to change the parts or clean the inner of faucet,
please follow the steps right to remove the parts.
FFAS0911-602500BF0
FFAS0912-702500BF0
48
20
240
114
102
150
70
G1/2
59
79
114
15
+
-
0
50
109
236
70
G1/2”
200
59
104
59
48
114
50
236
109
150
15
+
-
Cold
ON
Hot
Clod
ON
Hot
2
4
3
5
6
7
2.5mm
1. Close the Water Supply System
1
Remove all impurity in Aerator
Aerator
Soft Brush
Clean Water
Milano
Milano
- 2 -
- 3 -
1
2
3
4
5
6
7
8a
8b
9
10
Index Button
Screw
Handle
Cap
Nut
Cartridge
Stop Valve Handle
Body
Body
Screw
O-Ring
1
1
1
1
1
1
1
1
0
2
2
Installing the S-Connector
1
Installation
Installing the Hand Shower
3
11
12
13
14
15
16
17
18
19
20
Washer
Nut
Escutcheon
S-Connector
Aerator
Hose
Shower Hanger
Anchor
Shower
Diverter Valve
2
2
2
2
1
1
1
1
1
1
1
Screw
(Shower Hanger)
Anchor
Water Supply Pipeline(Hot)
S-C onne ctor
Water Supply Pipeline
(Cold)
FFAS0911 / FFAS0912
Parts List
Parts List
No. Part Name Q’ty No. Part Name Q’ty
* Consult the dimension drawing and lay the pipes.
* Wash and clean the water supply pipeline.
8b
18
20
2
1
4
3
5
6
7
8a
9
10
11
12
13
14
15
16
17
19
FFAS0911 / FFAS0912
1
1
1
1
1
1
1
0
1
2
2
2
2
2
2
0
0
1
1
1
1
34~39
1
50
2
lev el
Finished Wall
Escutcheon
Washer
Nut
Fanucet
2
1
3
3
0
S-Connector
Water Supply Pipeline(Cold)
Installing the Faucet
2
1
3
（Wall）
2
4
5
6
Water Supply Pipeline(Hot)
/
