OUTDOOR LIVING
Read the instructions and precautions before use of this product
MODEL NO: 50105347
3-PIECE POLY RESIN BISTRO SET
Instruction Manual
Limited Warranty
World Factory, Inc.® Products for Home Use
World Factory, Inc.® (Seller) warrants to the original Buyer only, that each Astonica™ Product will be free
from defects in material and workmanship for a period of one (1) year from date of purchase. SELLER’S
SOLE OBLIGATION AND BUYER’S EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL
BE THE REPAIR OR REPLACEMENT OF PARTS, WITHOUT CHARGE, WHICH ARE DEFECTIVE IN
MATERIAL OR WORKMANSHIP. ANY PARTS AS DETERMINED BY THE SELLER WHICH HAVE BEEN
MISUSED; ABUSED OR DAMAGED EITHER DIRECTLY OR INDIRECTLY FROM REPAIRS OR
ALTERATIONS ATTEMPTED BY UNAUTHORIZED PERSONS; IMPROPER MAINTENANCE, NEGLECT
OR ACCIDENT ARE NOT COVERED BY THIS LIMITED WARRANTY. This warranty does not apply to
damage, heat-induced coloration changes, scratching or alteration due to normal use or weathering. To
make a claim under this Limited Warranty, you must return the complete product, transportation prepaid, to
any World Factory, Inc.® authorized service center. Call 1-888-424-3354 for the location of the nearest
authorized service center.
Additional Limitations
THIS LIMITED WARRANTY DOES NOT APPLY TO ACCESSORY OR CONSUMABLE ITEMS RELATED
TO THIS PRODUCT. ALL IMPLIED WARRANTIES SHALL BE LIMITED IN DURATION TO ONE (1) YEAR
FROM DATE OF PURCHASE. IN NO EVENT SHALL SELLER BE LIABLE FOR ANY INCIDENTAL OR
CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO LIABILITY FOR LOSS OF PROFITS,
ARISING FROM THE SALE OR USE OF THIS PRODUCT.
If any provision of this Limited Warranty is for any reason held to be invalid or unenforceable, such provision
shall not affect any other provision herein, this Limited Warranty shall be construed as if such invalid and/or
unenforceable provision had never been contained herein.
This Warranty contains the entire agreement between Seller and Buyer and supersedes any and all prior
agreements, arrangements, or understandings between the parties relating to product warranty.
IF YOU HAVE ANY PROBLEMS OR QUESTIONS CONCERNING THIS PRODUCT,
DO NOT RETURN IT TO YOUR RETAILER, CONTACT CUSTOMER SERVICE AT
1-888-424-3354.
Please keep this instruction manual for future reference
IF YOU HAVE ANY PROBLEMS OR QUESTIONS CONCERNING THIS PRODUCT,
DO NOT RETURN IT TO YOUR RETAILER, CONTACT CONSUMER SUPPORT AT
1-888-424-3354
IF YOU ARE A STORE MANAGER OR EMPLOYEE IN NEED OF ASSISTANCE CALL
1-888-851-5569
PLEASE HAVE YOUR STORE NUMBER READY
OR
Made in China
©2003 Distributed by:
World Factory, Inc.
®
Southlake, TX 76092
PARTS & HARDWARE LIST
PART # DESCRIPTION QUANTITY
A 2Chair Back
B 2Chair Seat
C 8Chair leg
D
1
1
1
Table Top
Chair Center Brace
Table Center Brace
E
2
Table Leg
F
3
Medium Nut
G
11
Small Nut
H
22
Large Nut
Plastic Spanner
I
J
K
4
A
B
C
D
E
F
G
H
I
J
Carefully remove the contents from the package. If any parts are missing do not attempt to
use the product until they have been obtained and correctly installed.
Caution: Do not over tighten fasteners.
IF YOU HAVE ANY PROBLEMS OR QUESTIONS CONCERNING THIS PRODUCT,
DO NOT RETURN IT TO YOUR RETAILER. CONTACT CUSTOMER SERVICE AT
1-888-424-3354.
C
B
A
J
A
B
I
D
C
C
F
D
I
plastic studs
F
1. (See Figure 1) Insert studs on chair back (A)
through holes in chair seat (B) and secure
the back with 2 large nuts (J) and
2 medium nuts (I).
2. Insert studs on one chair leg (C) into chair
seat (B) and secure with 2 medium nuts (I)
and 1 large nut (J) with spanner. Repeat
for the other three legs. Be careful not to
over tighten the nuts.
3. (See Figure 2) Place the chair brace's (D)
threaded studs thru the tab on chair leg (C).
Turn the chair upside down and fasten the
brace (D) with medium nut (I) using the
plastic spanner to tighten nuts on all four
legs. Be careful not to over tighten the nuts.
4. (See Figure 3) Position table top (E) upside
down on a clean surface. Place the 2 holes
at the top of the leg (F) on the plastic
threaded studs on the bottom of the table (E)
and secure with large nuts (J) using the
plastic spanner (K) to tighten. Be careful
not to over tighten the nuts.
5. Position table right side up. Place the table
center brace's (G) threaded studs thru the
tab on table leg (F). Turn the table upside
down and fasten the brace (G) with medium
nuts (I) using the spanner on all four legs.
Tighten all fasteners securely. Be careful
not to over tighten the nuts.
Figure 1
Figure 2
Figure 3
K
E
J
K
G
K
G
I
F
/
