®
Model No: 50104288
Flynn 40” Round Dining Table
Instruction Manual
Read the instructions and precautions before use of this product
Please keep this instruction manual for future reference
Due to ongoing product development
the actual product or products may vary from
the illustrations or photos shown within this manual.
NOTE: This product is intended for residential, non-commercial use.
For warranty information, please refer to the back page of
this instruction manual.
Made in China
©2011 World Factory, Inc.
Distributed by:
World Factory, Inc.
Westlake, TX 76262
Limited Warranty
World Factory, Inc. Products for Home Use
World Factory, Inc. (Seller) warrants to the original Buyer only, that each Astonica Product will be free
from defects in material and workmanship for a period of one (1) year from date of purchase.
SELLER’S SOLE OBLIGATION AND BUYER’S EXCLUSIVE REMEDY UNDER THIS LIMITED
WARRANTY SHALL BE THE REPAIR OR REPLACEMENT OF PARTS, WITHOUT CHARGE, WHICH
ARE DEFECTIVE IN MATERIAL OR WORKMANSHIP. ANY PARTS AS DETERMINED BY THE
SELLER WHICH HAVE BEEN MISUSED; ABUSED OR DAMAGED EITHER DIRECTLY OR INDIRECTLY
FROM REPAIRS OR ALTERATIONS ATTEMPTED BY UNAUTHORIZED PERSONS; IMPROPER
MAINTENANCE, NEGLECT OR ACCIDENT ARE NOT COVERED BY THIS LIMITED WARRANTY. This
warranty does not apply to damage, heat-induced coloration changes, scratching or alteration due to
normal use or weathering. To make a claim under this Limited Warranty, you must return the complete
product with proof of purchase, transportation prepaid, to any World Factory, Inc. authorized service
center. Call 1-888-422-7800 for the location of the nearest authorized service center.
Additional Limitations
THIS LIMITED WARRANTY DOES NOT APPLY TO ACCESSORY OR CONSUMABLE ITEMS RELATED
TO THIS PRODUCT. ALL IMPLIED WARRANTIES SHALL BE LIMITED IN DURATION TO ONE (1)
YEAR FROM DATE OF PURCHASE. IN NO EVENT SHALL SELLER BE LIABLE FOR ANY INCIDENTAL
OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO LIABILITY FOR LOSS OF
PROFITS, ARISING FROM THE SALE OR USE OF THIS PRODUCT.
If any provision of this Limited Warranty is for any reason held to be invalid or unenforceable, such
provision shall not affect any other provision herein, this Limited Warranty shall be construed as if
such invalid and/or unenforceable provision had never been contained herein.
This warranty gives you special legal rights, and you may also have other rights which vary from state
to state.
This Warranty contains the entire agreement between Seller and Buyer and supersedes any and all
prior agreements, arrangements, or understandings between the parties relating to product warranty.
141011rev1
A Table Top 1
B Upper Table Leg 1
C Lower Table Leg 1
D Bolt 4
E Washer 4
F Hex Key 1
1. (SEE FIGURE 1) Place table top (A) upside
down on a non-scratching surface such as a
piece of carpet, blanket or large towel.
2. Turn the upper table leg (B) upside down so
that the holes at the top of the legs line up with
the holes underneath the table top (A). Then
do the same with the lower table leg (C). The
center support holes should fit flush together.
3. (SEE FIGURE 2) Secure each leg (B,C) to the
table top (A) using washer (E) and bolt (D).
4. (SEE FIGURE 3) Turn the table right side up.
5. All four legs should sit flat. If the table rocks,
the table legs have been mounted in reverse
order. If so, repeat steps 1 - 3 reversing the
placement order of the table legs.
PARTS & HARDWARE LIST
PART # DESCRIPTION QUANTITY
A
B
C
D
ASSEMBLY INSTRUCTIONS
Figure 1
Figure 2
Figure 3
CAUTION: Do not over tighten fasteners.
Carefully remove the contents from the package. If any parts are missing do not
attempt to use the product until they have been obtained and correctly installed.
D
B
E
A
C
NOTE: This product is intended for residential, non-commercial use.
Parts Detail
E
F
-
1
-
2
