Australian Warning Systems 4200 Series Installation and Operation Instructions

Brand: Australian Warning Systems

Model: 4200 Series

Type: Installation and Operation Instructions

Australian Warning Systems 4200 Series

The Australian Warning Systems 4200 Series is a compact and versatile high-intensity directional LED warning light suitable for mounting against front or rear windscreens inside a vehicle. Colorless until illuminated, these discrete LED lights offer self-contained electronics and feature-packed controls.

Key Features:

Compact and Versatile: Can be mounted on windshields or solid surfaces for maximum visibility.
High Intensity LEDs: 8 x 1-watt LEDs provide bright and attention-grabbing warnings.
Self-Contained Electronics: No external control box required for operation.

Australian Warning Systems 4200 Series

Key Features:

Compact and Versatile: Can be mounted on windshields or solid surfaces for maximum visibility.
High Intensity LEDs: 8 x 1-watt LEDs provide bright and attention-grabbing warnings.
Self-Contained Electronics: No external control box required for operation.

Australian Warning Systems Page 1

Australian Warning Systems 4200 series LED lights are compact and versatile

high intensity directional LED warning lights suitable for mounting against front

or rear windscreens inside a vehicle. Colourless until illuminated, these discrete

LED lights offer self contained electronics and feature packed controls.

Additional benefits of Australian Warning Systems LED lights include low

current draw, a long and maintenance free service life with reliable solid-state

operation and extremely low electromagnetic emissions. The LED lights are

dual voltage (12-24 VDC), and simply plug into the vehicle’s existing cigarette

lighter or accessory socket. Alternatively, the plug can be removed and the unit

hardwired through a switch.

WARNING!

Failure to install or use this product according to manufacturer’s recommendations may result in property

damage, serious bodily/personal injury, and/or death to you and those you are seeking to protect!

Do not install or operate this product unless you have read & understood the safety information contained below.

1. Proper installation combined with operator training in the use, care, and maintenance of emergency warning devices are

essential to ensure the safety of you and those you are seeking to protect.

2. Exercise caution when working with live electrical connections.

3. This product must be properly grounded. Inadequate grounding and/or shorting of electrical connections can cause high

current arcing, which can cause personal injury and/or severe vehicle damage, including fire.

4. Proper placement and installation are vital to the performance of this warning device. Install this product so that output

performance of the system is maximized and the controls are placed within convenient reach of the operator so that s/he

can operate the system without losing eye contact with the roadway.

5. Do not install this product or route any wires in the deployment area of an air bag. Equipment mounted or located in an air

bag deployment area may reduce the effectiveness of the air bag or become a projectile that could cause serious personal

injury or death. Refer to the vehicle owner’s manual for the air bag deployment area. It is the responsibility of the

user/operator to determine a suitable mounting location ensuring the safety of all passengers inside the vehicle.

6. It is the responsibility of the vehicle operator to ensure during use that all features of this product work correctly. In use, the

vehicle operator should ensure the projection of the warning signal is not blocked by vehicle components (i.e., open trunks

or compartment doors), people, vehicles or other obstructions.

7. The use of this or any other warning device does not ensure all drivers can or will observe or react to a warning signal.

Never take the right-of-way for granted. It is your responsibility to be sure you can proceed safely before entering an

intersection, driving against traffic, responding at a high rate of speed, or walking on or around traffic lanes.

8. This equipment is intended for use by authorized personnel only. The user is responsible for understanding and obeying all

laws regarding warning signal devices. Therefore, the user should check all applicable city, state, and federal laws and

regulations. The manufacturer assumes no liability for any loss resulting from the use of this warning device.

Specifications:

Voltage: 12-24VDC

Current: 0.5 amps @ 12VDC

0.25 amps @ 24VDC

Flash Patterns: 30

Light Source: 8 x 1 watt LED’s

Installation and Operation Instructions

4200 Series LED Dash Lights

Australian Warning Systems Page 2

Universal Mounting Bracket:

Using the universal mounting bracket, the 450-4200 LED lights may be mounted to the window of the vehicle with suction cups

or permanently mounted to a solid surface of the vehicle.

Permanent Mounting:

1. The 4200 series universal mounting bracket should be mounted to a flat surface. The mounting location should allow the

maximum visibility of the warning device to other road users, whilst allowing for sufficient wire access.

2. Using the mounting bracket as a template, mark the drill hole locations on the mounting surface. Drill mounting holes using

a suitable drill bit.

3. Rotate the LED head so that the beam is parallel with the road and visibility to approaching traffic is optimised.

Light Shield Mounting:

Using the light shield, the 4200 LED lights may be mounted to the window of the vehicle with suction cups or semi-permanently

using optional mounting tape.

1. Insert suction cups or apply tape on the flanges of the shield

2. Install on Windshield – Note: If possible, mount with the bracket in contact with the dashboard while secured to the

windshield.

3. Rotate the LED head so that the beam is parallel with the road and visibility to approaching traffic is optimised.

Wiring Instructions:

Insert the cigarette plug into the vehicle cigarette lighter. Flash patterns may be changed using the button marked “PATTERN” at

the rear of the housing. Press this button momentarily, 0-1 second to change to the next pattern, 1-3 seconds to change to the

previous pattern, and 3-5 seconds for the all LED’s to be steady on.

SYN Socket: Allows synchronisation with other LED lights of this type

RESET Button: Press to reset the flash pattern to pattern 1

H/L PWR: High / Low light intensity. Press to toggle between high & low light output

PATTERN: Press to change flash between 30 available flash patterns

Flash Patterns

No. Flash Pattern No. Flash Pattern

1 A&B Alternating Quad Burst with C&D 16 A&B Alternating Fast Single with C&D

2 A&D Alternating Quad Burst with B&C 17 A&D Alternating Fast Single with B&C

3 A&C Alternating Quad Burst with B&D 18 A&C Alternating Fast Single with B&D

4 Simultaneous Quad Burst (Phase 1) 19 Simultaneous Fast Single (Phase 1)

5 Simultaneous Quad Burst (Phase 2) 20 Simultaneous Fast Single (Phase 2)

6 A&B Alternating Quad Flash with C&D 21 A&B Alternating Variable with C&D

7 A&D Alternating Quad Flash with B&C 22 A&D Alternating Variable with B&C

8 A&C Alternating Quad Flash with B&D 23 A&C Alternating Variable with B&D

9 Simultaneous Quad Flash (Phase 1) 24 Simultaneous Variable Flash

10 Simultaneous Quad Flash (Phase 2) 25

A&B Alternating Quad, Single, Rapid &

Quad Burst with C&D

11 A&B Alternating Slow Single with C&D 26 Left to Right - Slow

12 A&D Alternating Slow Single with B&C 27 Left to Right - Medium

13 A&C Alternating Slow Single with B&D 28 Left to Right - Fast

14 Simultaneous Slow Single (Phase 1) 29 Combination

15 Simultaneous Slow Single (Phase 2) 30 Steady

12 Wedgewood Road, Hallam, 3803

Victoria, Australia

Ph: (03) 9796 5880

Fax: (03) 9796 5885

Email: [email protected]

www.warningsystems.com.au

Australian Warning Systems 4200 Series Installation and Operation Instructions

Brand: Australian Warning Systems

Model: 4200 Series

Type: Installation and Operation Instructions

Australian Warning Systems 4200 Series

Key Features:

Compact and Versatile: Can be mounted on windshields or solid surfaces for maximum visibility.
High Intensity LEDs: 8 x 1-watt LEDs provide bright and attention-grabbing warnings.
Self-Contained Electronics: No external control box required for operation.

Download PDF

report

Australian Warning Systems 4200 Series Installation and Operation Instructions

Australian Warning Systems 4200 Series Installation and Operation Instructions

Other documents