WALI WL-FTM-1 Installation guide

Brand: WALI

Model: WL-FTM-1

Category: Flat panel wall mounts

Type: Installation guide

Supplied Parts List

(4)M4x12 Bolt-h (4)M4x30 Bolt-i (4)M6x20 Bolt-j

(2)Monitor Bracket (1)Bubble Level-a

Note: The mounting components and hardware supplied in this package are

not designed for installations to walls with steel studs or to cinder block walls.

If the hardware you need for your installation is not included, please consult

your local hardware store for proper mounting hardware for the application.

Tools Required 4mm Drill Bit

Phillips Screwdriver

10mm Masonry Bit

Carpenter's Level

(4)M6 Washer-f(8)M6/M8 Spacer-d (4)M4 Washer-e

(4)M8x20 Bolt-l (4)M8x35 Bolt-m (4)M8x50 Bolt-n

(4)Lag Bolt-q(4)Lag Bolt Washer-p (4)Concrete Anchor-r

(4)M8 Washer-g

(1)Wall Plate

(4)M4 Spacer-c

(4)M6x35 Bolt-k

(4)Bolt Cover-o

(1)Allen Key-b

Step 1 Mounting the Wall Plate to the Wall

CAUTION!

WARNING

!This TV mount must be securely attached to the

vertical wall. If the mount is not properly

installed it may fall, resulting in possible injury

and/or damage.

65mm

4mm

Wood Studs Wall qp

Please don’t install

upside down.

Attention:

Brick or Concrete Wall

60mm

65mm

10mm

Please don’t install

upside down.

Attention:

Step 2 Mounting the Monitor Brackets to a TV

First of all, Once you have

determined the correct diameter, please see the diagram as below. You will thread the

Bolt into the TV using the correct Washer(e,f,g), and using the spacer(c,d) if necessary.

Please make sure the Monitor Brackets are vertically centered and level with each

other.

make sure the diameter of the Bolt(h to n) your TV requires.

Step 3 Attaching TV to Wall Plate and Adding the Safety Bolts

Warning: Some TVs may require two people to lift! We are not responsible for

personal injury or product damage.

First hook the Monitor Brackets over the top of the Wall Plate, then let the bottom of the

Monitor Brackets rotate to the bottom of the Wall Plate as shown in the below diagram.

Use the screw driver to tighten the safety bolts. Then the Monitor Brackets will sit

behind the bottom tab on the Wall Plate as shown in the diagram.

3.1

3.2

3.3

h to n

e,f,g

c,d

(if necessary)

Step 4 Level the TV Mount

Loosen four bolts by maximum ONE 360 degree turn as below diagram, then adjust the

level of the TV, finally fasten the bolts by supplied Allen Key(b).

WARNING: Don’t over loose the bolts to provent the TV from falling off!

Step 5 Adjusting the Tilting Angle

Adjust the TV to the desired angle and fasten the two bolts by the supplier Allen Key(b)

as below diagram.

WARNING: Don’t over loose the bolts to provent the TV from falling off!

This mount can be separated into two parts and used as two mounts as below.

Romve the four bolts by provided Allen key(b) to disconnect the front larger plate and

VESA 100 plate.

Part 2

Max 400x400mm

Part 1

Max 100x100mm

Part 1 can be used for TV with VESA 100x100mm mounting holes

Install the wall plate as the Step 1 on page 3, then connect the TV to plate by 4pcs M4

Bolts(h,i) and 4pcs M4 Washer(e). Use the M4 Spacer(c) if necessary.

Part 2 can be used for TV with Max VESA 400x400mm mounting holes

65mm

4mm

Wood Studs Wall

16"(406mm)

Part 2 Step 1A: Mounting the Wall Plate to the Wood Studs Wall

You may need to purchase extra lag bolts

and concrete anchors according to your

actual condition.

h,i

Part 2 can be used for TV with Max VESA 400x400mm mounting holes

Brick or Concrete Wall

60mm

65mm

10mm

Warning: Some TVs may require two people to lift! We are not responsible for

personal injury or product damage.

First hook the Monitor Brackets over the top of the Wall Plate, then let the bottom of the

Monitor Brackets rotate to the bottom of the Wall Plate as shown in the below diagram.

Use the screw driver to tighten the safety bolts. Then the Monitor Brackets will sit

behind the bottom tab on the Wall Plate as shown in the diagram.

3.1

3.2

3.3

Part 2 Step 1B: Mounting the Wall Plate to the Brick or Concrete Wall

Part 2 Step 2: See Step 2 on page 4.

Part 2 Step 3: Attaching TV to Wall Plate and Adding the Safety Bolts

You may need to purchase extra lag bolts

and concrete anchors according to your

actual condition.

WALI WL-FTM-1 Installation guide

Brand: WALI

Model: WL-FTM-1

Category: Flat panel wall mounts

Type: Installation guide

Download PDF

report

WALI WL-FTM-1 Installation guide

WALI WL-FTM-1 Installation guide

Related papers

Other documents