Disney 3401992P Assembly Instructions

Disney
Brand
Disney
Model
3401992P
Type
Assembly Instructions

This manual is also suitable for

Thank you for purchasing this quality product. Make sure you check all packaging materials
carefully for small parts that may have come loose inside the carton during shipment. Before
set up of the bed, identify and count all parts and hardware and compare with the parts and
hardware list provided in these instructions. Do not fully tighten the bolts until the bed
is completely set up.
1 -G1 Headboard Support
1 - G2 Footboard Support
2 -G3 HDBD Corner Support
2 -G4 FTBD Corner Support
2 -G5 HDBD Middle Support
2 - G6 FTBD Middle Support
**All parts are italicized in the assembly instructions.
1 - Headboard 1 - Footboard
( HDBD) ( FTBD)
Head
Foot
Left Side Panel
Right Side Panel
Foot Head Canopy Guard
Parts List
Pumpkin Finial Stem Finial 10-Canopy
Support Tubes
Plastic end cap 10pcs
#992-35T-1/2
#992-35F-1/2
Hardware List - For HB/FB/SR
e3/4"
Hardware List - For Canopy
Allen Bolt 10pcs
1/4"*1-1/4"
a
c4mm Allen Wrench 1pc
Assembly Instructions
VENDOR: GLOB
SKU NO. STYLE NO. DESCRIPTION
36019924 992-35T-1 TWIN CARRIAGE HB/FB + RAILS
36119926 992-35T-2 TWIN CANOPY
36219928 992-35F-1 FULL CARRIAGE HB/FB + RAILS
36319920 992-35F-2 FULL CANOPY
Page 1/5
d4pcs
L=7" Lock latch
Hardware List - For (Pre-mounted)
b1/4"*1-1/2" Sunk Allen Bolt 1pc
(*)
G5
G6
G3
G4
G2
G1
G3
G4
G5
G6
992-35T/F-2 Hardware Pack Location
992-35T/F-1 Hardware
Pack Location
Hardware Pack Location
Page 2/5
Headboard
Left Side Panel
Right Side Panel
Footboard
VENDOR: GLOB
SKU NO. STYLE NO. DESCRIPTION
36019924 992-35T-1 TWIN CARRIAGE HB/FB + RAILS
36119926 992-35T-2 TWIN CANOPY
36219928 992-35F-1 FULL CARRIAGE HB/FB + RAILS
36319920 992-35F-2 FULL CANOPY
Assembly Instructions
VENDOR: GLOB
SKU NO. STYLE NO. DESCRIPTION
36019924 992-35T-1 TWIN CARRIAGE HB/FB + RAILS
36119926 992-35T-2 TWIN CANOPY
36219928 992-35F-1 FULL CARRIAGE HB/FB + RAILS
36319920 992-35F-2 FULL CANOPY
Step 1
-Pull out part (d) from pre-mounted iron frame.
-Trace the labels, identify the headboard, footboard, right-side rail and
left-side rail. Lift the headboard and left-side rail, using Lack latch (d) insert
from top to bottom to connect together, make sure cotter pin connect
properly.Do the same procedure for footboard and side rail.
Page 3/5
"Right Side Panel" Label Stick at Bottom
"Left Side Panel " Label stick
at Bottom
"Headboard" Label
Stick at Bottom
"Footboard" Label
Stick at Bottom
dTop
Assembly Instructions
VENDOR: GLOB
SKU NO. STYLE NO. DESCRIPTION
36019924 992-35T-1 TWIN CARRIAGE HB/FB + RAILS
36119926 992-35T-2 TWIN CANOPY
36219928 992-35F-1 FULL CARRIAGE HB/FB + RAILS
36319920 992-35F-2 FULL CANOPY
Step 2
Uncrew pre-mounted component " pumpkin finial " & "Stem Finial"
Relocate the stem finial to top of pumpkin finial, use allen wrench to fasten (b) the
sunk Allen bolt
b
b
d
(Pull out)
Pre-mounted in box Fully assembled
Pre-mounted in box
Fully assembled
c
c
Top Press the cotter pin to pass through the
hole, make sure construction hold tight.
Page 4/5
Assembly Instructions
VENDOR: GLOB
SKU NO. STYLE NO. DESCRIPTION
36019924 992-35T-1 TWIN CARRIAGE HB/FB + RAILS
36119926 992-35T-2 TWIN CANOPY
36219928 992-35F-1 FULL CARRIAGE HB/FB + RAILS
36319920 992-35F-2 FULL CANOPY
Step 3
Locate the canopy supports G1, G2, G3, G4, G5, and G6. You should have a
total of 10 canopy supports (2 each of G3,G4, G5, AND G6). Insert the
canopy support tubes in to the corresponding canopy guard tubes, and press
the bottom clip to fix each side.
Step 4
Insert the metal tube into the corresponding headboard/footboard/side rail metal
cover, for example G1 to G1, G2 to G2.
Check that all bolts are tightened securely. The bed is now fully assembled.
keep (e) plastic end cap for furture use.
e
Page 5/5
Assembly Instructions
VENDOR: GLOB
SKU NO. STYLE NO. DESCRIPTION
36019924 992-35T-1 TWIN CARRIAGE HB/FB + RAILS
36119926 992-35T-2 TWIN CANOPY
36219928 992-35F-1 FULL CARRIAGE HB/FB + RAILS
36319920 992-35F-2 FULL CANOPY
Step 5
Using allen wrench to secure allen bolt (a) to the bottom of tube rail.
a
c
Step 6 (If assembled without canopy)
please disassmbled steps 2~5.
Put the plastic end cap into the hole which originally placed canopy tubes
before.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

Disney 3401992P Assembly Instructions

Disney
Brand
Disney
Model
3401992P
Type
Assembly Instructions
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents