ACTi PPSW-1101 Quick Installation guide

ACTi
Brand
ACTi
Model
PPSW-1101 Quick
Category
Network switches
Type
Installation guide

This manual is also suitable for

L2/L4 Managed Gigabit Ethernet Switch
GS-4210 Series
Quick Installation Guide
Table of Contents
1. Package Contents ....................................................................................... 3
2. Requirements ............................................................................................. 4
3. Terminal Setup ........................................................................................... 5
4. Logon to the Console .................................................................................. 6
5. ConguringIPAddressviatheConsole ........................................................ 7
6. SavingtheCongurationviatheConsole ...................................................... 9
7. Starting Web Management .........................................................................10
8. SavingCongurationviatheWeb ...............................................................13
9. RecoveringBacktoDefaultConguration .....................................................14
10. Customer Support ..................................................................................... 15
3
1. Package Contents
Thank you for purchasing PLANET L2/L4 Managed Gigabit Ethernet Switch.
“Managed Switch”mentionedinthisGuidereferstotheGS-4210Series.
Open the box of the Managed Switch and carefully unpack it. The box should
containthefollowingitems:
z TheManagedSwitch
z QuickInstallationGuide
z RS-232toRJ45ConsoleCable
z Rubber Feet
z TwoRack-mountingBracketswithAttachmentScrews
z PowerCord
z SFPDustCaps
If any item is found missing or damaged, please contact your local reseller for
replacement.
4
2. Requirements
z Workstations running Windows XP/2003/Vista/7/8/2008, MAC OS X or later,
Linux,UNIX,orotherplatformsarecompatiblewithTCP/IPprotocols.
z WorkstationsareinstalledwithEthernetNIC(NetworkInterfaceCard)
z Serial Port Connection(Terminal)
The above Workstations come with COM Port (DB9) or USB-to-RS-232
converter.
The above Workstations have been installed with terminal emulator, such as
HyperTerminalincludedinWindowsXP/2003.
Serial cable-- oneend isattached to theRS-232 serialport, whilethe other
endtotheconsoleportoftheManagedSwitch.
z Ethernet Port Connection
Network cables--Usestandardnetwork(UTP)cableswithRJ45connectors.
The above PC is installed with Web browser and JAVA runtime environment
plug-in.
Note
It is recommended to use Internet Explore 8.0 or above to access
the Managed Switch. If the Web interface of the Managed Switch
is not accessible, please turn off the anti-virus software or firewall
andthentryitagain.
5
3. Terminal Setup
To congure the system, connect a serial cable to a COM port on a PC or
notebook computer and to the RJ45 type of the console port of the Managed
Switch.
Managed Switch
PC / Workstation
with
Terminal Emulation Software
Serial Port
RS-232 to RJ-45 Cable
Console Port
RJ-45
Figure 3-1 Managed Switch Console Connectivity
A terminal program is required to make the software connection to the Managed
Switch.
1. Run terminal program on the OS.
2.When the following screen appears, make sure that the COM port should be
conguredas:
zBaud :115200
zDatabits :8
zParity :None
zStopbits :1
zFlowcontrol :None
Figure 3-2: COM Port Conguration
6
4. Logon to the Console
Once the terminal is connected to the device, power on the Managed Switch, and
the terminal will display “running testing procedures”.Then, the following message
asks to log-in user name and password. The factory default user name and
passwordareshownasfollows,andtheloginscreeninFigure4-1appears.
Username:admin
Password:admin
Figure 4-1: Managed Switch Console Login Screen
The user can nowenter commands to manage the Managed Switch.For a detailed
descriptionofthecommands,pleaserefertothefollowingchapters.
Note
1.For security reason, please change and memorize the new pass-
wordafterthisfirstsetup.
2.Only accept command in lowercase letter under console inter-
face.
7
5.ConguringIPAddressviatheConsole
TheManagedSwitchisshippedwithdefaultIPaddressasfollows:
IPAddress:192.168.0.100
SubnetMask:255.255.255.0
To check the current IP address or modify a new IP address for the Switch, please
usetheproceduresasfollows:
Show the current IP address
1.Atthe“GS-4210 Series#”prompt,enter“show ip”.
2.Thescreendisplays thecurrent IPaddress, SubnetMask andGatewayas shown
inFigure5-1.
Figure 5-1: IP Information Screen
8
Conguring IP address
3.Atthe“GS-4210 Series#”prompt,enter“congure”.
4.At the “GS-4210 Series(cong)#” prompt, enter the following command and
press <Enter>asshowninFigure5-2.
GS-4210Series(cong)# ip address 192.168.1.100 mask 255.255.255.0
GS-4210Series(cong)# ip default-gateway 192.168.1.254
ThepreviouscommandwouldapplythefollowingsettingsfortheSwitch.
IP Address: 192.168.1.100
Subnet Mask: 255.255.255.0
Gateway: 192.168.1.254
Figure 5-2: IP Address Screen
5.RepeatStep1tocheckiftheIPaddressischanged.
If the IP is successfully congured, the Managed Switch will apply the new IP
address setting immediately. You can access the Web interface of the GS-4210
ManagedSwitchSeriesthroughthenewIPaddress.
Note
Ifyouarenotfamiliarwithconsolecommandortherelatedparam-
eter,enter“?”anytimeinconsoletogetthehelpdescription.
9
6.SavingtheCongurationviatheConsole
In the switch, the running conguration le stores in the RAM. In the current
version, the running conguration sequence running-cong can be saved from the
RAM to FLASH by writing the command or copying the running-cong startup-
cong command, so that the running conguration sequence becomes the startup
congurationle,whichiscalledcongurationsave.
1.At the “GS-4210 Series#” prompt, enter “copy running-cong startup-
cong”asshowninFigure6-1.
Figure 6-1: The Conguration Screen
10
7. Starting Web Management
Thefollowing shows howto start upthe Web Management of theManaged Switch.
Note the Managed Switch is congured through an Ethernet connection. Please
makesurethemanagerPCmustbesetonthesameIPsubnetaddress.
Forexample, the default IP address of the Managed Switch is 192.168.0.100, then
the manager PC should be set at 192.168.0.x (where x is a number between 1
and254,except100),andthedefaultsubnetmaskis255.255.255.0.
PC / Workstation
with Web Browser
192.168.0.x
Managed Switch
RJ45/UTP Cable
IP Address:
192.168.0.100
Figure 7-1: IP Management Diagram
Logging in to the Managed Switch
1.Use Internet Explorer 8.0 or above Web browser and enter IP address
http://192.168.0.100toaccesstheWebinterface.
2.When the following dialog box appears, please enter the default user name and
password“admin”.TheloginscreeninFigure7-2appears.
DefaultUsername:admin
DefaultPassword:admin
11
Figure 7-2: Login Screen
3.Afterenteringthepassword,themainscreenappearsasFigure7-3shows.
Figure 7-3: Web Main Screen of Managed Switch
12
The Switch Menu on the left of the Web page lets you access all the commands
andstatisticstheManagedSwitchprovides.
Figure 7-4: Switch Menu
Now, you can use the Web management interface to continue the Switch
management.
Pleaserefertotheuser’smanualformore.
13
8.SavingCongurationviatheWeb
In the Managed Switch, the running conguration le stores in the RAM. In the
currentversion, therunning congurationsequence of running-cong can be saved
from the RAM to FLASH by “Save Congurations to FLASH” function, so that
therunning conguration sequencebecomes the startup congurationle, which is
calledcongurationsave.
To save all applied changes and set the current conguration as a startup
conguration, the startup-conguration le will be loaded automatically across a
system reboot.
1. Click “Save > Save Congurations to FLASH”tologin “CongurationManager”
Page.
2. Press the “Apply”buttontosaverunningcongurationtostartupconguration.
14
9.RecoveringBacktoDefaultConguration
IP Address has been changed or admin password has been forgotten –
To reset the IP address to the default IP Address “192.168.0.100” or reset the
login password to default value, press the hardware reset button on the front
panel for about 10 seconds. After the device is rebooted, you can login the
managementWebinterfacewithinthesamesubnetof192.168.0.xx.
RESET
Figure 9-1: GS-4210 Series Reset Button
15
10. Customer Support
Thank you for purchasing PLANET products. You can browse our online FAQ
resourceandUser’s ManualonPLANETWebsite rst tocheckif itcouldsolveyour
issue.Ifyouneed moresupportinformation, pleasecontactPLANET switchsupport
team.
PLANETonlineFAQ:
http://www.planet.com.tw/en/support/faq.php?type=1
Switchsupportteammailaddress:
[email protected]
GS-4210SeriesUser’sManual:
http://www.planet.com.tw/en/support/download.php?type1=1&model=&type=3
(PleaseselectyourswitchmodelnamefromProductModeldropdownmenu)
Copyright©PLANETTechnologyCorp.2014.
Contentsaresubjecttorevisionwithoutpriornotice.
PLANETisaregisteredtrademarkofPLANET TechnologyCorp.Allother trademarks
belongtotheirrespectiveowners.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

ACTi PPSW-1101 Quick Installation guide

ACTi
Brand
ACTi
Model
PPSW-1101 Quick
Category
Network switches
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents