Planet GS-4210-8P2T2S Quick start guide

GS-4210-8P2T2S
Planet
Brand
Planet
Model
GS-4210-8P2T2S
Category
Network switches
Type
Quick start guide

This manual is also suitable for

Planet GS-4210-8P2T2S is a high-performance and feature-rich managed switch that provides businesses and organizations with a reliable and secure network solution. With its 8 Gigabit Ethernet ports, 2 SFP ports, and a range of advanced features, this switch is ideal for a variety of applications, including high-speed data transfer, VoIP, video conferencing, and IP surveillance.

Planet GS-4210-8P2T2S is a high-performance and feature-rich managed switch that provides businesses and organizations with a reliable and secure network solution. With its 8 Gigabit Ethernet ports, 2 SFP ports, and a range of advanced features, this switch is ideal for a variety of applications, including high-speed data transfer, VoIP, video conferencing, and IP surveillance.

L2/L4 Managed Gigabit Ethernet Switch
GS-4210 Series
Quick Installation Guide
Table of Contents
1. Introduction ............................................................................................... 3
2. Package Contents ....................................................................................... 4
3. Requirements ............................................................................................. 5
4. Terminal Setup ........................................................................................... 6
5. Logon to the Console .................................................................................. 7
6. ConguringIPAddressviatheConsole ........................................................ 8
7. SavingtheCongurationviatheConsole ..................................................... 10
8. Starting Web Management .........................................................................11
9. SavingCongurationviatheWeb ...............................................................13
10.RecoveringBacktoDefaultConguration ....................................................14
11. Customer Support ..................................................................................... 16
3
1. Introduction
Thank you for purchasing PLANET L2/L4 Managed Gigabit Ethernet Switch. The
descriptionofthismodelisshownbelow:
GS-4210-8P2S 8-Port10/100/1000T802.3atPoE+2-Port100/1000XSFP
ManagedSwitch
GS-4210-8P2T2S 8-Port10/100/1000T802.3atPoE+2-Port10/100/1000T
+2-Port100/1000XSFPManagedSwitch
GS-4210-24P4C 24-Port10/100/1000T802.3atPoE+4-PortGigabitTP/
SFPComboManagedSwitch/220W
GS-4210-24PL4C 24-Port10/100/1000T802.3atPoE+4-PortGigabitTP/
SFPComboManagedSwitch/440W
GS-4210-48T4S 48-Port10/100/1000T+4-Port100/1000SFPManaged
GigabitSwitch
GS-4210-48P4S 48-Port10/100/1000T802.3atPoE+4-Port100/1000X
SFPManagedSwitch/440W
“Managed Switch” is used as an alternative name in this Quick Installation
Guide.
4
Open the box of the Managed Switch and carefully unpack it. The box should
containthefollowingitems:
2. Package Contents
Model Series GS-4210-
ModelName
Package Item 8P2S 8P2T2S 24P4C/
24PL4C
48T4S/
48P4S
TheManagedSwitch 
QuickInstallationGuide 
RS-232toRJ45ConsoleCable -  -
RubberFeet 
TwoRack-mountingBrackets
withAttachmentScrews 
PowerCord 
SFPDustCaps 2244
If any item is found missing or damaged, please contact your local reseller for
replacement.
5
3. Requirements
zWorkstations running Windows XP/2003/Vista/7/8/2008, MAC OS X or later,
Linux,UNIX,orotherplatformsarecompatiblewithTCP/IPprotocols.
zWorkstationsareinstalledwithEthernetNIC(NetworkInterfaceCard)
zSerial Port Connection(Terminal)
The above Workstations come with COM Port (DB9) or USB-to-RS-232
converter.
The above Workstations have been installed with terminal emulator, such as
HyperTerminalincludedinWindowsXP/2003.
Serial cable-- One endisattachedtotheRS-232serialport,whiletheother
endtotheconsoleportoftheManagedSwitch.
zEthernet Port Connection
Network cables--Usestandardnetwork(UTP)cableswithRJ45connectors.
 The above PC is installed with Web browser and JAVA runtime environment
plug-in.
Note
It is recommended to use Internet Explore 8.0 or above to access
the Managed Switch. If the Web interface of the Managed Switch
is not accessible, please turn off the anti-virus software or firewall
and then try it again.
6
4. Terminal Setup
The GS4210-8P2T2S, GS-4210-24P4C and GS-4210-24PL4C are equipped with a
console interface for local switch setup and maintenance. To congure the system,
connect a serial cable to a COM port on a PC or notebook computer and to the
RJ45typeoftheconsoleportoftheManagedSwitch.
Managed Switch
PC / Workstation
with
Terminal Emulation Software
Serial Port
RS-232 to RJ45 Cable
Console Port
RJ-45
Figure 4-1 Managed Switch Console Connectivity
A terminal program is required to make the software connection to the Managed
Switch.
1. Run terminal program on the OS.
2.When the following screen appears, make sure that the COM port should be
conguredas:
zBaud :115200
zDatabits :8
zParity :None
zStopbits :1
zFlowcontrol :None
Figure 4-2 COM Port Conguration
Note
Console interface is not available for the GS-4210-8P2S, GS-4210-
48T4SandGS-4210-48P4S.
7
5. Logon to the Console
Once the terminal is connected to the device, power on the Managed Switch and
the terminal will display “running testing procedures”. Then, the following message
asks to log-in user name and password. The factory default user name and
passwordareshownasfollows,andtheloginscreeninFigure5-1appears.
Username:admin
Password:admin
Figure 5-1: Managed Switch Console Login Screen
The user can now enter commands to manage the Managed Switch. For a detailed
descriptionofthecommands,pleaserefertothefollowingchapters.
Note
1.For security reason, please change and memorize the new pass-
wordafterthisfirstsetup.
2.Only accept command in lowercase letter under console inter-
face.
8
6.ConguringIPAddressviatheConsole
TheManagedSwitchisshippedwithdefaultIPaddressasfollows:
IPAddress:192.168.0.100
SubnetMask:255.255.255.0
To check the current IP address or modify a new IP address for the Switch, please
usetheproceduresasfollows:
Show the current IP address
1.Atthe“GS-4210 Series#”prompt,enter“show ip”.
2.The screen displaysthe current IP address, SubnetMask andGatewayas shown
inFigure6-1.
Figure 6-1: IP Information Screen
Conguring IP address
3.Atthe“GS-4210 Series#”prompt,enter“congure”.
4.At the “GS-4210 Series(cong)#” prompt, enter the following command and
press <Enter>asshowninFigure6-2.
GS-4210Series(cong)# ip address 192.168.1.100 mask 255.255.255.0
GS-4210Series(cong)# ip default-gateway 192.168.1.254
9
ThepreviouscommandwouldapplythefollowingsettingsfortheSwitch.
IP Address: 192.168.1.100
Subnet Mask: 255.255.255.0
Gateway: 192.168.1.254
Figure 6-2: IP Address Screen
5.RepeatStep1tocheckiftheIPaddressischanged.
If the IP is successfully congured, the Managed Switch will apply the new IP
address setting immediately. You can access the Web interface of the GS-4210
ManagedSwitchSeriesthroughthenewIPaddress.
Note
If you are not familiar with console command or the related
parameter, enter “?” anytime in console to get the help descrip-
tion.
10
7.SavingtheCongurationviatheConsole
In the switch, the running conguration le stores in the RAM. In the current
version, the running conguration sequence running-cong can be saved from the
RAMtoFLASHbywriting the command or copying the running-cong startup-
cong command, so that the running conguration sequence becomes the startup
congurationle,whichiscalledcongurationsave.
At the “GS-4210 Series#” prompt, enter “copy running-cong startup-
cong”asshowninFigure7-1.
Figure 7-1: The Conguration Screen
11
8. Starting Web Management
The following shows how to start up the Web Management of the Managed
Switch. Note the Managed Switch is congured through an Ethernet connection.
Please make sure the manager PC must be set on the same IP subnet address.
For example, the default IP address of the Managed Switch is 192.168.0.100,
then the manager PC should be set at 192.168.0.x (where x is a number
between1and254,except100),andthedefaultsubnetmaskis255.255.255.0.
PC / Workstation
with Web Browser
192.168.0.x
Managed Switch
RJ45/UTP Cable
IP Address:
192.168.0.100
Figure 8-1: IP Management Diagram
Logging in to the Managed Switch
1.Use Internet Explorer 8.0 or above Web browser and enter IP address
http://192.168.0.100toaccesstheWebinterface.
2.When the following dialog box appears, please enter the default user name and
password“admin”.TheloginscreeninFigure8-2appears.
DefaultUsername:admin
DefaultPassword:admin
Figure 8-2: Login Screen
12
3.Afterenteringthepassword,themainscreenappearsasFigure8-3shows.
Figure 8-3: Web Main Screen of Managed Switch
The Switch Menu on the left of the Web page lets you access all the commands
andstatisticstheManagedSwitchprovides.
Figure 8-4: Switch Menu
Now, you can use the Web management interface to continue the Switch
management.
Pleaserefertotheuser’smanualformore.
13
9.SavingCongurationviatheWeb
In the Managed Switch, the running conguration le stores in the RAM. In the
currentversion, therunning congurationsequence of running-congcan be saved
from the RAM to FLASH by “Save Congurations to FLASH” function, so that
the running conguration sequence becomes the startup conguration le, which is
calledcongurationsave.
To save all applied changes and set the current conguration as a startup
conguration, the startup-conguration le will be loaded automatically across a
system reboot.
1. Click “Save > Save Congurations to FLASH” to login “Conguration
Manager”Page.
2. Press the “Apply” button to save running conguration to start up congura-
tion.
14
10.RecoveringBacktoDefaultConguration
IP Address has been changed or admin password has been forgotten –
To reset the IP address to the default IP Address “192.168.0.100” or reset the
login password to default value, press the hardware reset button on the front
panel for about 10 seconds. After the device is rebooted, you can login the
managementWebinterfacewithinthesamesubnetof192.168.0.xx.
2
1
4
3
6
5
8
9 10
7
PoE In-use
Mini-GBIC
GS-4210-8P2S
8-Port 10/100/1000T
802.3at PoE +
2-Port 100/1000X SFP Managed Switch
PWR
12345678
RESET
ACTLNK
1000
ACTLNK
1000
FAN
Alert
Figure 9-1: GS-4210-8P2S Reset Button
4 6 82
1 3 5 7
10
911 12
Mini-GBIC
2468
1SYS
PWR
357
10 12
9 11
ACTLNK
PoE In-Use
ACT
LNK
1000
RESET
Console
115200,N,8,1
GS-4210-8P2T2S
PoE
12-Port Gigabit 802.3at PoE
Managed Switch
Figure 9-2: GS-4210-8P2T2S Reset Button
4 6 82 10 12 14 16
9 11 13 151 3 5 7
18 20 22 24
17 19 21 23
26 28
25 27
PWR
SYS
115200, N, 8, 1
Console
RESET
2 6 10 14 18 22
4 8 12 16 20 24
1 5 9 13 17 21
3 7 11 15 19 23
GS-4210-24PL4C
26
25
28
27
26
25
28
27
26 28
25 27
FAN 2
FAN 1
PoE PWR
ACTLNK
1000
ACTLNK PoE In-Use
ACTLNK
1000
PoE
Alert
Figure 9-3: GS-4210-24P(L)4C Series Reset Button
15
48-Port 10/100/1000T
+
4-Port 100/1000X SFP Managed Switch
GS-4210-48T4S
RESET
SYS
PWR
52
51
50
49
4 6 82 12 14 1610 20 22 2418 28 30 3226 36 38 4034
44 46 48
42
3 5 71 11 13 159 19 21 2317 27 29 3125 35 37 3933
43 45 47
41
1000LNK/ACT
5250
51
49 1000 LNK/ACT
100 LNK/ACT
Figure 9-4: GS-4210-48T4S Reset Button
GS-4210-48P4S
RESET
SYS
PWR
52
51
FAN2
FAN1
50
49
4 6 82 12 14 1610 20 22 2418 28 30 3226 36 38 4034
44 46 48
42
5250
51
49 1000 LNK/ACT
100 LNK/ACT
48-Port 10/100/1000T
802.3at
+
4-Port 100/1000X SFP Managed Switch
3 5 71 11 13 159 19 21 2317 27 29 3125 35 37 3933
43 45 47
41
PoE In-useLNK/ACT
Figure 9-5: GS-4210-48P4S Reset Button
16
11. Customer Support
Thank you for purchasing PLANET products. You can browse our online FAQ
resourceandUser’s ManualonPLANET Websiterst to checkifit couldsolveyour
issue.Ifyouneed moresupportinformation, pleasecontactPLANET switchsupport
team.
PLANETonlineFAQ:
http://www.planet.com.tw/en/support/faq.php?type=1
Switchsupportteammailaddress:
[email protected]
GS-4210SeriesUser’sManual:
http://www.planet.com.tw/en/support/download.php?type1=1&model=&type=3
(PleaseselectyourswitchmodelnamefromtheProductModeldropdownmenu)
Copyright © PLANET Technology Corp. 2015.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their
respective owners.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

Planet GS-4210-8P2T2S Quick start guide

GS-4210-8P2T2S
Planet
Brand
Planet
Model
GS-4210-8P2T2S
Category
Network switches
Type
Quick start guide
This manual is also suitable for

Planet GS-4210-8P2T2S is a high-performance and feature-rich managed switch that provides businesses and organizations with a reliable and secure network solution. With its 8 Gigabit Ethernet ports, 2 SFP ports, and a range of advanced features, this switch is ideal for a variety of applications, including high-speed data transfer, VoIP, video conferencing, and IP surveillance.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents