Polyaire Zonemaster ZoneTouch V2 Installation guide

ZoneTouch V2

Zone Control System

Installation Manual

www.polyaire.com.au

ZONEMASTER ZONETOUCH V2 ZONE CONTROL SYSTEM - Installation Manual 1

1) Application 2

2) Features 2

3) Components 3

4) Configuration 4

5) Pre-Installation 6

6) Component Installation 7

7) Recommended Commissioning Procedure 10

7.1 Setting Parameters 10

1) Touch Screen Address 11

2) Number of Groups in the System 11

3) Supply Air Safety High & Low Limits 12

4) Spill/Bypass Mode 13

5) Installer Settings Password 14

7.2 Grouping Zones 15

7.3 Balancing Zones 15

7.4 Naming Groups 16

7.5 Enabling/Disabling Service Reminder 17

7.6 Testing Damper On/Off 18

8) Troubleshooting Guide for Installers 19

TABLE OF CONTENTS

Liability

Please read the instructions before installing this Zonemaster Zoning Control System.

Polyaire Pty Ltd does not accept any responsibility for loss or damage that may occur as a result of the incorrect

installation of this Zonemaster Control System.

ZONEMASTER ZONETOUCH V2 ZONE CONTROL SYSTEM - Installation Manual

1) Application

The Zonemaster ZONETOUCH V2 control system is a fully featured and engineered

 systemthatisdesignedtomanagetheairowfromtheACunitprovidingabalanced

 andmanagedairowtoalloutlets.Itiswellsuitedtoallductedreversecycle,ducted

 heatingandcoolingsystemsinlightcommercial,residentialandapartmentapplications.

2) Features

For Installers

 • 24voltsforeasyandsafeinstallationandmaintenance.

 • Userfriendly5”touchscreeninterfacetosimplifysetupprocess.

 • Supportsupto16individualzones(Zone1,2…9,A,B…G),16groups(Group1,

2…9,A,B…G)withmaximumof4zonesinagroup.Ninezones/groupsand

  abovewillrequireanextensionmodule.

 • Remotezonebalancing---eachzone’sopeningpositioncanbeprogrammedfor

  balancingviatouchscreenbetween10-100%.

• Autospill/bypass(dedicatedbypasszoneport)---thedesignatedzonedampers

areforcedopenwhenallzonesareturnedo.

 • Safetysystem---Opensalldampersifthesupplyairtemperaturereaches

low or high limit.

 • Dampersareconnecteddirectlytothemaincontrolmoduleoritsextension

module for easy diagnosis.

For End Users

• Userfriendlylargetouchscreencontrolinterface.

 • Intuitiveuserinterface.

 • Controlairowtoindividualgroups.

 • ColourLCDforclearerdisplay.

 • Personalizedsystemsettingsandgrouplabelling

 • Wallmountedwithuptotwotouchscreensavailableinasystem.

 • 5-1-1ProgrammableOn/Otimeprograms.

 • Oneselectableturbogrouptocool/heataparticularareaquicker.

 • Halfyear,OneyearandTwoyearservicealertsremindcustomerstocall

  technicianforcleaningandservicingACsystem.

 • Allzonesautomaticallyresumetheiroriginalon/ostateoncepowerisrestored

after power outage.

ZONEMASTER ZONETOUCH V2 ZONE CONTROL SYSTEM - Installation Manual 3

3) Components

Note: Each component is sold separately or in kits.

3.1 Wall Controller (Touch Screen)

Users can input control commands from the wall

   controllertoturnagroup/zoneonando.Itisused

toinputallprogramparameters.ThecolourLCD

   displaysclock,zonestatus,temperatureandother

statuses.

3.2 Main Control Module and Extension Module

(optional)

Maincontrolmodule(8zoneswithbypassport)and

itsoptionalextensionmodule(extra8zones)control

thepositionofmotorizeddamperofeachzone.

3.3 Motorized Damper (Bright Green)

Motorizeddamperdrivesthebladeofthedamperto

   adjusttheairow.

3.4 Cables

   Cableswithleftlatch(fordata)orcentrallatch(for

   control)plugsconnectthemaincontrolmodule,

   extensionmodule(ifapplicable),touchscreen,and

   motorizeddampertogether.

3.5 Supply Air Sensor (optional)

Supply air sensor measures the temperature of the

supply air for safety purposes.

3.6 Power Supply

24VACtransformersprovidepowertothemaincontrol

   moduleandextensionmodule.

3.7 Rechargeable Battery

Thebackupbatteryisusedtostorethetimeand

settings when there is a power surge.

ZONEMASTER ZONETOUCH V2 ZONE CONTROL SYSTEM - Installation Manual

4)Conguration

The Zonemaster ZONETOUCH V2 system is a star architecture system that allows

 communicationsbetweentheZONETOUCHV2maincontrolmodule,extensionmodule,

 upto16zonedampers,anduptotwotouchscreens.Figure1showstheconnection

 ofdevicessuchasZONETOUCHV2extensionmodule,twotouchscreens,andeight

 damperstothemainmodule.Figure2showstheconnectionofeightdamperstothe

 extensionmodule.Figure3showsthelinkingofthemainmoduletotheextension

module and touch screens.

Eightmotorizeddamperscanbeconnectedtothemaincontrolmodule.

Ninedampersandabove(upto16)willneedtheextensionmodule.

Inaddition,thereisadedicatedbypassportwhereadamperisusedtoreturnthe

supplyairdirectlytothereturnairduct.(SeeSpill/BypassModeonpage13)

Extension Module

Anextensionmodulecanbepluggedintothemaincontrolmoduletoexpandthe

numberofzonesto16asshowninFigure2.Aseparate24VACpowersupplyis

requiredtosupplypowertotheeightextrazones.

Figure 1: ZoneTouch Main Module connected to 2 Touchpads and 8 Dampers

ZONEMASTER ZONETOUCH V2 ZONE CONTROL SYSTEM - Installation Manual 5

The wiring of the ZONETOUCH V2 system is straightforward. A cable with central

latchedplugsconnectsamotorizeddampertotherelevantoutputportclearlymarked

onthemaincontrolorextensionmodule.

Themainmoduleandextensionmodulecanbeindierentlocationsandconnected

viaacablewithleftlatchedplugsonbothendsasshowninFigure3.Touchscreenis

connectedtothe‘T’portonmainmoduleusingacablewithleftlatchedplugs.

Up to two touch screens can be joined in a system. The two touch screens are

connected to each other with a double left latched adaptor in serial.

Figure 2: Zone Touch with Extension Module and 8 Zone Dampers

Figure 3: ZoneTouch Main Module with Extension Module and 2 Touchpads

ZONEMASTER ZONETOUCH V2 ZONE CONTROL SYSTEM - Installation Manual

5) Pre-Installation

Goodplanningleadstoasuccessfulzonesysteminstallation.Beforephysically

 installingandcommissioningazoningsystem,pleasecompletethefollowinglistedtasks:

 5.1Decidehowmanyzones(dampers)aretobecontrolledinthesystem.

5.2 Assign lowerorderzones(1,2,3…)todampersclosesttothereturnairgrille.

  Thesezoneswillautomaticallyopenwhenspillingisrequired.Howeveravoidusing

  lowerorderzonesforbedroomsasthismaycausediscomfortifautospilling

occurs during sleep time.

5.3 Groupzonesaccordingtocustomer’srequirements.Eachgroupinitiallyhasone

  zonebutcanhaveuptoamaximumoffourzones(Example:Therecouldbeone

  ormorezonesgoingintoacommonareasuchasKitchen/DiningorFamily/Dining

  room).Workoutthetotalgroupnumber(Maximumtotalgroupnumberinasystem

is 16).

5.4 Recordtheabovementionedinformationtotable1and2onpage11intheUser

  manualandtothetableonthestickeroftheMainControlModule.

NOTE: It is important to test all cables

before installation. Testing all cables to

be used before the start of the installation

will save considerable diagnostic time if

the fully installed system is subsequently

found to have a problem. Cable testing is

quick and easy with a Zonemaster Cable

tester available from Polyaire

Cable Tester

(ItemNumber:657089)

Note: When installing two touch screens, use a long cable (as long as

practical) between the main module and the double left latched adaptor,

two short cables between the adaptor and two touch screens and try to

maintain the two short cables at the same length.

ZONEMASTER ZONETOUCH V2 ZONE CONTROL SYSTEM - Installation Manual 7

6) Component Installation

6.1 Mountthemaincontrolmoduleand/orextension

  module(ifusingmorethan8zones)byscrewing

  thebox(es)toaroofframeorPolyaireDiusion

  Fitting(PDF).

 6.2 Remove thetwo-sidecoversonthemaincontrol

  modulesothatallLEDsandsocketsforzone

  dampersareexposed.

6.3 If extensionmoduleisused,connectmainmodule

  toextensionmoduleat‘E’portonbothmodules

  withaonemetreleftlatchedcable(provided).

6.4 Use pre-testedcabletoconnect‘Z1’portonthe

  mainmoduletothemotorizeddamperofthe1st

  zone.

 6.5 Repeat step6.4toconnectotherzonedampers,

  includingbypassdamper(‘B’port)ifinstalled,

  totheirrelevantzoneportsonthemaincontrol

  moduleandextensionmodule.

6.6 Mount the supply air sensor in the supply air duct

  betweenthefancoilandtherstdamperandpush

the plug of supply air temperature sensor into the

  socketonthemaincontrolmodule(Optional).

 6.7 Connectthetouchscreentothe‘T’portonthe

  mainmodule.Iftwotouchscreensareused,

  usetheprovidedleftlatchedcablesanda1-to-2

  female-femalesplittercouplertojoinalltouch

  screens.(Seeinstructionsbelowontmentof

touch screen to wall).

6.8 Connect the 24VAC transformer to screw terminals

  onthemaincontrolmodule.Ifextensionmoduleis

  used,connectanother24VACtransformertothe

  screwterminalsoftheextensionmodule.

ZONEMASTER ZONETOUCH V2 ZONE CONTROL SYSTEM - Installation Manual

 6.9 Ifbothtransformers(mainmoduleandextension

  module)sharethesamepowerswitch,switchthe

power on. (IMPORTANT NOTE) If NOT, switch on

  thepowertoextensionmodulerst.Thenturn

on the power to main module.Otherwise,the

  extensionmodulewillNOTbeinitializedproperly.

  CircularRedLEDonthemainmodule(and

  extensionmodule)shouldbeonandthesystemwill

  startinitializing&nishinabout30secondsafter

power on.

6.10 Install the battery as shown in the picture on the

main control module. It is recommended to install

the battery after power is on. Otherwise the system

  maynotbeinitializedproperlyduetothelow

  voltageofthenewbattery.

 6.11 Replacethesidecoversbackonthemaincontrol

  andextensionmoduleoncenishedsettingand

commissioning.

6.12 Recordthegroupedzonesandbalancingdetails

  onthestickerotheMainControlModuleafter

commissioning the system.

6.13 FittheTouchScreen to wall

Theplasticcasingofthetouchscreenconsistsoftwohalves.Thefrontcover

  containsthePCBboardalongwiththeLCD/touchscreen.Thebackcover

  attachestothewallasamountingbase.Duringtheinstallationprocessthecase

  willhavetobeopenedtomountthetouchscreenonthewall.Followthesteps

  belowtocarefullyinstallthetouchscreentothewall:

  a) Slidethebackbasetobottomsidetoclearthestopsonthefrontcover

  b) Removethebasefromthefrontcover

c) Position thebackbaseonthewallwherethecableis(about1.5mhighfrom

   theoor).Ensureitisawayfromanyheatorcoolsourceandmarkthecable

hole and screw holes.

NOTE: The correct back cover direction is marked on its surface; follow that

  markwhenxingthebackcover.

ZONEMASTER ZONETOUCH V2 ZONE CONTROL SYSTEM - Installation Manual 9

d) Cut therectangularholeforthecableandxthebackbasetothewallby

   usingfourscrewsonthemarkedpositions.

e) Retrieve thetouchscreencable(frommain

control module) out of the cable hole and plug it

into the touch screen.

f) Alignthebottomedgeofthebackbasewiththe

   bottominsideofthefrontcoverandthetwoside

   edgesofthebackbasewiththefrontcover.

g) Gentlypushthefrontcoveragainstthewalland

   makesurethebackoffrontcoverisushagainst

   thewall.Andthenpushthefrontcover

   downwardswithtwoguresholdingthetopside

   ofthefrontcoverwheretherearetwoslotstill

   thetwosnap-onsclickin.

ZONEMASTER ZONETOUCH V2 ZONE CONTROL SYSTEM - Installation Manual

7) Recommended Commissioning Procedure

7.1 Setting Parameters

System parameters canbesetupfrom‘InstallerSettings’screen.

Followthestepsbelowtosetrequiredvalues.Touchingbuttoninthe

  settingprocesswillgobackto the home screen from any setting pages.

a) Touchonthehomescreen(Figure3)toenter‘Settings’screen

   ( F i g u r e 4).

  b) On‘Settings’screen,touchbuttontoshowthekeyboardfor

   e n t e r i n g thepasswordofinstallersettings(Figure5).

c) Enter thepasswordofinstallersettings(Figure6),thedefaultpasswordis

‘Polyaire’.

NOTE: The password is case sensitive. Maximum length for the password is

eight characters but it can also be blank.

Figure 3.

Figure 5.

Figure 4.

Figure 6.

ZONEMASTER ZONETOUCH V2 ZONE CONTROL SYSTEM - Installation Manual 11

7.1.1 Touch Screen Address

Up to two touch screens can be installed in one system. Each touch screen has

 adefaultaddressof‘1’.Duringcommissioningeachtouchscreenshouldbe

  assignedauniqueaddressforcommunicatingwiththemaincontrolmodule

  properly.FollowthefollowingstepstosettheTouchscreenAddress:  

a) On‘InstallerSettings’screen(Figure6),touch‘Parameter’togetto‘Parameter’

   screen(Figure7).

b) Touch theediteldof‘TouchpadAddress’tohighlightit,and

   buttonswillappear(Figure8).

c) Use and buttons to select a touchpad address from 1 to 2.

NOTE: Each controller (touch screen) must have a unique address.

Two touch screens with the same address will cause communication

problems between the main control module and the touch screens.

7.1. 2 Number of Groups in the System

For the purpose of groupstatusdisplayandspill/bypasszonecalculation,the

  systemneedstoknowthetotalnumberofgroupstobeinstalled.Thefactory

default number is 8.

IMPORTANT: This number must be equal to the total group number used

in the system as planned in Pre-Installation process. If this is wrong, the

system may not work properly.

a) Touch the totalgroupeld,and

buttonswillappear(Figure9).

b) Press or button to change

to the total number of groups in the

system. The selectable number is

from 1 to 16.

Figure 7. Figure 8.

Figure 9.

ZONEMASTER ZONETOUCH V2 ZONE CONTROL SYSTEM - Installation Manual

7.1.3 Supply Air Safety High & Low Limits

Forsafetyreasons,thesystemcanmonitorthe supply air temperature. A

supply air sensor must be inserted at the supply air end of the AC and the other

  endistobeconnectedtotheMainmodule,asshownonPage7forthissafety

  functiontobeactivated.Ifthetemperaturemovesoutsidethesetlimits,all

dampers in the system will be forced open. The factory default setting for the

  safetycontrolis“disabled”.Itisoptionalforusingthisfunction.

a) Onthe‘Parameter’screen(Figure6),touch the radio button of high limit and low

limit to enable or disable safety function.

If the supply air sensor has not been installed or the supply air sensor is faulty

   a n d thereplacementsensorisnotavailableimmediately,thesystemcanstillrun

by disabling the safety function.

b) Highlight the high limit or low limit

   b y touchingtheediteldsaccordingly,

   a n d thenadjustthemtotherequired

   v a l u e bytouchingorbutton

   ( F i g u r e 10).

The adjustable range of the high limit

is from 45°C to 75°C and adjustable

range of the low limit is from 0°C to

   15 ° C . Thefactorydefaultvaluesare

60°C for high limit and 5°C for low limit.

NOTE: If the limits are reached,

‘Safety is Activated’ will be displayed

on the home screen (Figure 11). The

ON/OFF function of groups will be

disabled till supply air temperature

moves back within the limits or the

High Limit and Low Limit protection is

disabled (there is about one minute

delay after disabling the protection).

Check the air conditioning unit.

Figure 10.

Figure 11.

ZONEMASTER ZONETOUCH V2 ZONE CONTROL SYSTEM - Installation Manual 13

7.1.4 Spill/Bypass Mode

Bypass and spill modes are another safety feature of the ZONETOUCH V2

  systemtopreventpressurefrombuildingupandcausingductdamage.This

  usuallyoccursifsomeonehasturnedoalldamperswhiletheA/Cunitis

  runningleadingtoapressurebuildup(andpotentialofductpuncture,blow-os

or joints splitting).

Whenopenedzonesinthesystemarelessthanthebypass/spillset-point

  whichisapercentageofopenedzonesagainsttotalzones,thedesignatedspill

  dampersorBypassdamperwillbeautomaticallyopenedtopreventpressure

from building up.

Spill Mode

  Thisisaprogramdesignedtoautomaticallyopenseveraldampersifsomeone

  attemptstoshutdownalldampersthuspreventingpressurebuildup.Spillmode

  usesthezoneswithloweraddressesinthesystem.Whenallocatingaddresses

  t o zonesinspillmode,itisstronglyrecommendedtogiveloweraddressesto

  thosezonesthathavehigherspillprivileges.Thesezonesarenormallylocated

  closertothereturnairgrilles.Thelowertheaddress,thehigherthespillprivilege

  thezonehas.

AnotherpointtorememberisDONOTusebedroomsasspillzones.Duringsleep

  timeiftheairconditionerisonandspillzonesareautomaticallyforcedtoopen,

  t h e spillzoneswillbeverycoldorhot.Thismaycausediscomfortifbedrooms

  areusedasspillzones.

Whenthespillset-pointisreached,themaincontrolmoduleinstructszone1to

  openasspillzone.Iftherstspillzonecannotsatisfythespillaircontrol,zone2

  willautomaticallyopentospillexcessair.Thisprocesswillcontinueuntilthespill

  airset-pointissatisedinthesystem.Example:Inaneightzonesystem,ifset

  pointissetat30%thenitwillhaveatleast3(calculatedvalue=2.4)ormore

  zonesremainingopen.

Bypass Mode

  InBypassModethereisanextradamperandalengthofductthatgoesdirectly

  fromthesupplyairductbacktothereturnairduct.Themaincontrolmodule

  instructsthebypassdampertoopenanddumpexcessairtothereturnairduct.

Thebypassdampershouldbecarefullysizedtobeabletohandleexcessairwhile

  allzonesareclosed.Thebypassdampershouldbeconnectedtothe‘B’porton

the main control module.

Thefactorydefaultissetinspillmodeandtheset-pointis30%.Whenthesetpoint

  isreachedforspill,thehomescreenshows‘SpillisActivated‘andsomeofthe

  lowerorderzonesremainopenandthestatusoftheGroupswilldisplay‘Spill’in

  thehomescreen(Figure12)ifthelowerordergroupswereclosed.

ZONEMASTER ZONETOUCH V2 ZONE CONTROL SYSTEM - Installation Manual

Similarlyifbypassset-pointisreached,thescreendisplays‘BypassisActivated’

  asshowninFigure13.

Spill/Bypass Settings

a) In the‘Parameter’screen(Figure7),touchtheoptionbuttonsofspillorbypass

to select spill mode or bypass mode.

b) Touchspill/bypassediteldtomakeiteditable,andthenand

buttons will appear.

c) Touch orbuttontochangethespill/bypassset-pointtorequired

   v a l u e . Theadjustablerangeisfrom0%to50%with10%increments.

IMPORTANT: DO NOT set spill/bypass set-point to 0% unless there is a

permanent open zone used as spill zone. Otherwise, there will be no spill

zone when all zones are closed and damage may be caused by high

pressure build up inside ducts if air conditioner is running.

Figure 12. Figure 13.

Figure 14.

7.1.5 Installer Settings Password

The password which will be used in

  Figure5istopreventunauthorized

changing of the installer settings.

  Toresetthispassword,touchthe

  passwordediteldinthe‘Parameter’

  screen(Figure7),andthentypeinthe

  newpasswordandtouch‘Enter’key

  toconrmthepasswordchange

  (Figure14).

ZONEMASTER ZONETOUCH V2 ZONE CONTROL SYSTEM - Installation Manual 15

Figure 15. Figure 16.

Figure 17.

7.2 Grouping Zones

For ease of control operation,multiplezonescanbegroupedtogether.The

  groupedzonesaretreatedasonegroupwithitsownnameandturnedonoro

  together.Individualbalanceddamperpositionisnotaectedbygrouping,

  whichmeanszonebalancingcanbeconductedbeforeoraftergrouping.

Groupingcanbecarriedoutasfollows:

  a )  I n ‘InstallerSettings’screen(Figure6),touch toenter‘Grouping’

   screen(Figure15).

7.3 Balancing Zones

Remote balancing feature of ZONETOUCH V2oerstheexibilityofbalancing

  theamountofairowtoeachzoneelectronically.Oncetheopeningpositionof

  thedamperisset,thedamperwillonlyopentothisposition.Thedefaultsetting

  foreachdamperis100%openingpositionandtheadjustablerangeisbetween

  10%and100%.Thebalancingsettingscanbeconductedonthetouchscreen

as below.

a) In ‘InstallerSettings’screen(Figure

   6 ) , touch

b) The system will show a prompt

   ( F i g u r e 17)andthenenterthe

   ‘Balancing’screen(Figure18).

  b) Touchtheediteldofthegroup, and buttons will appear.

c) Touch or buttontoaddorminuszonestothegroup

  d) Repeatstepsb)andc)todeneallgroups.

NOTE: The maximum number of zones in a group is four. The zones to be

grouped will be consecutive zones. The factory default for grouping is that

each group has one zone.

7.4 Naming Groups

Thenameofagroupissetas‘Group_address’(e.g.Group_1)indefaultsetting.

  Thenamescanbecustomizedasfollows:

a) In ‘InstallerSettings’screen(Figure

   6 ) , touchtoenter

   ‘Naming’screen(Figure20).

b) Touchtheediteldofagroupto

rename it. A name list will appear for

   selection(Figure21).

c) Touch a name in the list to specify

   t h e nametothegroup,andalso

you can touch to enter

   o r editanamemanually(Figure22).

d) TouchtoconrmortouchtocancelandbacktoNaminglist

   pageortouchtocancelandbacktothehomescreen.

  c) Clicktheediteldtoselectthezonetobebalanced,theeldwillbe

   highlightedthenandbuttonswillappear(Figure19).

d) Touch or button to adjust the balance percentage.

e) Touch button to accept the changes just made.

NOTE:

  • Thebalancing menu will display all 16 zones irrespective of the number

of zones actually present in the system.

 • Thebalancing percentages of the inactive zones remain locked and show

as N/A.

  • The OPEN % value on the Zoning screen can be operated by the user for

   additionalairowadjustmenttothegroups.Theoverallopening%ofthe

zone is calculated as OPEN % x Balance %.

ZONEMASTER ZONETOUCH V2 ZONE CONTROL SYSTEM - Installation Manual

Figure 18. Figure 19.

Figure 20.

ZONEMASTER ZONETOUCH V2 ZONE CONTROL SYSTEM - Installation Manual 17

Figure 21. Figure 22.

Figure 23.

Figure 24.

7.5 Enabling/Disabling Service Reminder

Thereisabuilt-inservicereminderintheZONETOUCHV2systemforhalfyear,

one year and two years to automatically display an alert notifying customers

  t h a t theairconditioningsystemisdueforservice.Installerscanalsousethis

  featuretoleavetheirdetailssuchastheirnamesandcontactnumbers.

Theservicereminderwilldisplay‘HALFYEARSERVICEDUE’,‘ONEYEAR

  SERVICEDUE’or‘TWOYEARSERVICEDUE’andinstaller’snameandcontact

number on touch screen for the set number of days if it has been enabled for

  halfyear(182days),oneyear(365),twoyears(728days)respectivelysincethe

  airconditioningsystemhadbeencommissionedorservicedasshowningure

  26.Thedaysinthe‘Service’screenwillautomaticallyresetto1after728days

  orcanbemanuallychanged.TheServiceReminderisdisabledbydefaultbut

  canbeenabledasfollows:

a) In the‘InstallerSettings’screen

   ( F i g u r e 6),touch to

   e n t e r the‘Service’screen(Figure23).

b) Touchtheservicereminderoption

buttons to enable or disable the

   relevantreminders.

c) Touchtheediteldtochangetothe

desired setting. The installer name

and number can be entered by

   usingakeyboard(Figure24).

or buttons can be used to adjust

   reminderandrunningdays(Figure25).

Maximum length of the name is 10

characters and the phone number is

12 digits.

ZONEMASTER ZONETOUCH V2 ZONE CONTROL SYSTEM - Installation Manual

Figure 25.

Figure 26.

   Reminderinformationwillbe

displayed on the right side of the

   touchscreenwhentheserviceisdue

   ( F i g u r e 26)forthelengthofthe

   reminderdays(5daysinthe

   exampleofgure23).Touchingthe

information area will clear the alert

before the set reminder days has

reached.

The running days show how many

   d a y s havingpassedsincethesystem

   h a s beencommissionedorserviced.

It will automatically start from 1 for

   e v e r y 728days.

NOTE: Record the above parameters

such as Grouped Zones & Balancing

on the sticker of the Main Control

  ModuleandtheSystemConguration,GroupedZonesalongwithNamed

Groups, Balancing and Installer details to table 1, 2, 3 and 4 respectively on

page 11 and 12 of the User manual for future reference.

 7.6 TestingDamperOn/O

a) Switch on the air conditioner.

b) Enter the home screen of ZONETOUCH V2.

c) Touch thegroupbuttonstoturngroupsonorotocheckifthedampersare

correctly connected by feeling the air at the outlet.

d) The Turbogroupcanbetestedbyselectingtherelevantchosengroupas

   Tu r b o modeinthe‘UserSettings’andthenpressthegroupbuttonuntil

   a c t i v e turbomodeisdisplayedonthescreenforthatparticulargroup.

NOTE: Bypass zone damper cannot be tested via touch screen. It has to be

checked by observing the indicator on the damper motor.

Page is loading ...

Polyaire Zonemaster ZoneTouch V2 Installation guide

Related papers

Other documents