Sika 112729 User manual

Type
User manual

This manual is also suitable for

Sika 112729 is a polymer-based, two-component anchoring adhesive that is perfect for everyday anchoring projects and heavy-duty anchoring projects like anchoring bolts, dowels, railings, pins, deck supports, and pipes. It is easy to use with a standard caulk gun and cures quickly, making it a great choice for both DIYers and professionals.

Here are some of the key features and benefits of Sika 112729:

  • Fast curing - Can be used in as little as 30 minutes
  • High strength - Bonds to a variety of surfaces, including concrete, brick, and metal
  • Versatile - Can be used for both indoor and outdoor applications

Sika 112729 is a polymer-based, two-component anchoring adhesive that is perfect for everyday anchoring projects and heavy-duty anchoring projects like anchoring bolts, dowels, railings, pins, deck supports, and pipes. It is easy to use with a standard caulk gun and cures quickly, making it a great choice for both DIYers and professionals.

Here are some of the key features and benefits of Sika 112729:

  • Fast curing - Can be used in as little as 30 minutes
  • High strength - Bonds to a variety of surfaces, including concrete, brick, and metal
  • Versatile - Can be used for both indoor and outdoor applications
MATERIALS:
• Safety glasses and gloves • Utility knife • Cartridge of Sika AnchorFix®-1 or Sika® AnchorFix-2
• Standard caulk gun • Rotary hammer drill • Nylon brush
SITE PREP & PROCEDURE
1. Remember to always wear chemical resistant gloves and safety glasses at all times.
2. Drill a hole to the correct diameter and depth using a rotary hammer drill.
3. Clean the hole using a stiff nylon brush and blow out with compressed air (repeat process).
Make sure all particles, dust, and loose debris are all completely removed to ensure a proper bond.
4. Unscrew the cap on the Sika AnchorFix® cartridge. Pull the red plug and cut the plastic behind the
clip attached to the red plug. Next, attach the mixing nozzle over the cut plastic and insert the
cartridge into a standard caulk gun.
5. Squeeze the gun a few times to dispense the material through the nozzle. Discard the first part of
the dispensed material until a uniform gray color is achieved. If the hole is in hollow masonry, use a
perforated sleeve/screen.
6. Insert the mixer nozzle into the rear of the hole and start to squeeze the gun to dispense the
material. Withdraw the nozzle as the hole is slowly filled to prevent any air pockets.
7. Immediately insert the rod and/or bolt into the hole. This should be done slowly with a slight
twisting motion. Excess adhesive should be removed from the mouth of the hole before it sets.
8. Leave the rod/bolt undisturbed until the cure time has passed, then attach
the fixture and tighten necessary hardware.
9. Clean tools immediately with a solvent such as acetone, following the
manufacturer’s precautions. Cured material can only be removed mechanically.
Sika AnchorFix-1 For everyday anchoring projects (bolts, dowels, railings, pins, etc.)
Sika AnchorFix-2 For heavy duty anchoring projects (railings, deck supports, pipes, etc.)
usa.sika.com/retail y Refer to Product Data Sheet for more information.
ANCHORING ADHESIVES
Sika AnchorFix®- 1 & 2
HOW-TO GUIDE
  • Page 1 1

Sika 112729 User manual

Type
User manual
This manual is also suitable for

Sika 112729 is a polymer-based, two-component anchoring adhesive that is perfect for everyday anchoring projects and heavy-duty anchoring projects like anchoring bolts, dowels, railings, pins, deck supports, and pipes. It is easy to use with a standard caulk gun and cures quickly, making it a great choice for both DIYers and professionals.

Here are some of the key features and benefits of Sika 112729:

  • Fast curing - Can be used in as little as 30 minutes
  • High strength - Bonds to a variety of surfaces, including concrete, brick, and metal
  • Versatile - Can be used for both indoor and outdoor applications

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI