Stein Georgia Installation Instructions Manual

Brand: Stein

Model: Georgia

Type: Installation Instructions Manual

GEORGIA SQUARE

SHOWER - 2 SIDED

INSTALLATION INSTRUCTIONS

DEC 2014 | V2

GEORGIA SQUARE

SHOWER - 2 SIDED

INSTALLATION INSTRUCTIONS

PLEASE READ CAREFULLY

GENERAL INFORMATION

Thank you for choosing Stein Bathroomware. When you receive your Georgia Square Shower

package please check for any damage. If damage has occurred advise your supplier

immediately and do not proceed with installation.

DISCLAIMER

Stein International Ltd are not liable for any Georgia Square shower unit that has not been

installed correctly.

GLASS WARRANTY CLAIMS

Glass breakages on site are not replaced under warranty.

SAFETY GUIDE

• The glass requires two people to handle.

• Always stand glass up after unpacking the components and use soft packing when in

contact with hard surfaces. Take care not to strike an edge or corner on a hard surface.

• All glass is toughened and cannot be reworked or drilled.

• Wear protective gloves and eye protection.

• Special care should be taken when drilling walls to avoid hidden pipes or electrical cables

TOOLS REQUIRED

• Soft pencil and masking tape

• Spirit level and large square

• Screwdrivers

• Tape measure

• Drill and bits

• Hammer

MATERIALS REQUIRED

• Sika Silaex NG Translucent

• Rags and suitable cleaning materials

WE RECOMMEND THAT A PROFESSIONAL SHOWER INSTALLER IS USED FOR

INSTALLATION OF THIS PRODUCT TO ENSURE THE BEST RESULTS

7 8

Before commencing installation, please ensure you have the following components in your

package to complete installation.

Door front assembly channel x1

Fixed panel wall channel x1

Fixed return panel x1

Door front assembly x1

Handle set x1

Fixed panel screws 8mm x15

Fixed panel screw caps x8

Wall jamb xing screws 35mm x8

Corner channel - front door only installation x1

PACKAGE CONTENTS

ASSEMBLY DIAGRAM

Qty.Tick Ref Contents

SHOWER TYPE FRONT PANEL (A) MIN/MAX RETURN PANEL (B) MIN/MAX

900x900 Two Sided 830mm to 885mm 835mm to 865mm

1000x1000 Two Sided 930mm to 985mm 935mm to 965mm

1200 x 1000 Two Sided 1140mm to 1195mm 935mm to 965mm

WALL

CHANNEL

WALL

CHANNEL

B A

LAYOUT PLAN

IMPORTANT:

• A & B measurements are the minimum outer boundary line of glass channels.

• Measurements are based on the oor being level, walls plumb and all surfaces at. Any

variations must be taken into account when marking out the position within the minimum to

maximum range.

checked

PREPARATION CHECKLIST

THE FOLLOWING ITEMS MUST BE COMPLETED PRIOR TO INSTALLATION

Solid xing must be provided in the walls behind the wall channels. Refer to the

‘Layout Plan’ on page 3 to establish your shower type.

To ensure a successful result, the walls must be plumb and the oor at and level.

Contract a plumber to ensure waste tting is correctly installed.

ACRYLIC INSTALLATION OPTION

To install acrylic tray and liner, please refer to separate installation instructions with

packaged with product.

TILE INSTALLATION OPTION

Wall and oor surfaces must be waterproofed by a Certied Applicator and a Producer

Statement provided for the local council.

All tiling must be completed and allowed to cure before installing the shower enclosure.

INSTALLATION OF GEORGIA SQUARE SHOWER - 2 SIDED

Go to the Layout Plan on Page 3 and identify the shower type you are installing. Mark

out the outside line positioning of the wall channels within the minimum to maximum

range to suit your requirements.

Using these points mark out the position of the Front Door Assembly Channel (1) and

the Fixed Return Panel (3) onto the tray.

Mark the outside line and the wall channels (1) and (2) with a spirit level. Through the

holes in the channel pre-drill the start of the hole as a guide (refer Diagram A1).

Apply a bead of silicone down the back of the channels (1) and (2) and x in place with

screws (8) checking that they remain plumb (refer Diagram A2).

DIAGRAM A:

A1 A2

Slide Fixed Return Panel (3) and Door Assembly (4) into Wall Channel (1).

Hint: Insert the top or bottom corner of the panel into the channel rst. Then the rest

of the panel will slide into the channel easier.

Slide the Fixed Return Panel (3) over the extrusion on to the Front Door Assembly (4) at

the leading corner. Ensure this is aligned correctly then drilled and screwed.

DIAGRAM B:

DIAGRAM C:

DRILL HERE

THEN FIX

HERE

AERIAL VIEW

Using the sliding rails within the Front Door Assembly adjust them (in or out) to have

both the Fixed Return Panel and Front Door Panel positioned on the boundary line. They

should be positioned evenly between both wall channels.

Drill and fasten off the bottom rail on the inside (Diagram D1). Using a level ensure the

front assembly and return panel are plumb vertically at the corner junction and drill and

fasten the top rail (Diagram D2).

Drill four equally spaced 3.2mm holes into the wall channels (1) and (2) on the INSIDE of

the screen.

Make sure that your drill holes are more than 20mm back from the glass edge when using

the smallest screen size. Otherwise you risk breaking the glass.

Make sure that all the holes go though both the aluminium of the xed side panel and

the door front assembly. Fix off wall channels (1) and (2) to xed side panels (3) and (4)

using the xed panel screws (6) and covering them with screw caps (7).

DIAGRAM D:

DIAGRAM E:

D1 D2

DRILL 3.2 HOLES BETWEEN THE END OF

THE FIXED GLASS AND END OF DOOR.

FRONT VIEW OF SHOWERINSIDE SHOWER VIEW

ONLY ONE

HOLE IN

BOTTOM RAIL

SLIDING

RAIL

SLIDING

RAIL

20MM

DRILL HERE

OUTSIDE OF SHOWER

Handle Assembly: Screw the threaded rod into the handle.

Slide top post on to the the threaded rod,

making sure the post is facing the right

way.

Put standard screw into cap base, then

into washer, then into lower hole in the

glass. On the other side of the glass, slide

lower post onto the standard screw

making sure the post faces the right way.

Bring the handle up to the glass allowing

the top post to locate into the hole in the

glass. Fix the knob onto the threaded rod

making sure the washer is between the

glass and the knob.

Line up the hole in the handle with the

standard screw and post assembly. Screw

tightly together.

Place cap over base.

Apply silicone sealer around all external joints of shower screen a minimum of 24 hours

for silicone to set.

Silicone is not used on the inside of the shower screen because water can build up over

time within the wall channel and leak out of the shower area. The screen is designed to

allow the water to return into the shower area, if any is present. SCREENS THAT ARE

SEALED ON THE INSIDE WILL VOID WARRANTY.

SILICONE SEAL

TO OUTER EDGE

113 Newton Street, Mount Maunganui

Freephone 0800 002 299

Phone +64 7 928 9990

www.stein.co.nz

Stein Georgia Installation Instructions Manual

Brand: Stein

Model: Georgia

Type: Installation Instructions Manual

Download PDF

report

Stein Georgia Installation Instructions Manual

Stein Georgia Installation Instructions Manual

Other documents