ProCore Plus LWD8053RCB Installation guide

Brand: ProCore Plus

Model: LWD8053RCB

Type: Installation guide

This manual is also suitable for

INSTALLATION INSTRUCTIONS

PROCORE® PLUS INSTALLATION INSTRUCTIONS

Quick Reference:

Concrete moisture requirement For all on and below grade concrete, use a 6-mil (0.006-in.) Polyehtylene (PE) sheet or

equivelent

Flatness tolerance < 1/8-in. over 6-ft. and 1/16-in. over 1-ft. in all directions

Installation temperature Between 60°F to 80°F (16°C to 27°C)

Optimal service temperature Between 40°F to 90°F (4°C to 32°C)

Additional acoustic underlayment Not required or recommended

Expansion gap (entire perimeter) 1/4-in. ≤ 50-ft., and 1/2-in. between 50 – 85-ft. lengths or widths

Expansion joints (large areas) Only required if > 85-ft. in length or width

3-IN-1 doorway transition Not usually required

3-Season rooms Acceptable (but see “Expansion Gap”)

Pet stain warranty Yes, but immediately clean up when discovered

General Information & Limitations: Please watch the installation videos available at Lowes.com. This ﬂooring has a high-density

core (HDC), designed to be installed indoors only, as a “ﬂoating ﬂoor” for residential applications. The optimal operating temperature

is between 40°F to 90°F (4°C to 32°C). Avoid prolonged exposure to direct sunlight or other heat sources where temperatures will

exceed 90°F (32°C), as damage may occur. This product is not suitable for heavy rolling loads. Rolling chairs with soft or W-type

casters and a maximum rolling weight of 250 lbs. are acceptable – otherwise, use a vinyl chair mat in rolling chair areas. Failure to

observe these requirements could result in joint damage or failure. Do not secure ﬂooring or furniture to the subﬂoor with mechanical

fasteners or adhesives. Do not install cabinets, kitchen islands, or other non-movable furniture on top of this ﬂoor covering. Contact the

technical department at 1-888-509-3438 or techsupport@novalis-intl.com for assistance. Copies of ASTM documents are available

for purchase at www.astm.org.

Recommended Tool List:Appropriate Personal Protective Equipment (PPE) including safety glasses, gloves and suitable dust mask.

Appropriate tools to prepare the substrate, Hepa ﬁltered vacuum, 6-ft. and 1-ft. straight edge or level, two quarters (U.S. coins),

tape measure, pencil, speed square, utility knife with blades,1-lb. (∼ 16-oz.) rubber or soft faced dead blow hammer (preferred)

or rubber mallet, chalk-line, pull-bar, Oscillating Multi-Tool or hand saw (door jambs), wedge spacers or similar, jigsaw with carbide

blades, knee pads. If required, use a super-glue liquid adhesive for any small pieces.

Warning:All local, state, and federal regulations must be followed; this includes the removal of in-place asbestos (ﬂoor coveringand

adhesive) andanylead-containing material. The Occupational Safety and Health Administration (OSHA) has exposure limits for people

exposed to respirable crystalline silica; this requirementmust be followed. Do not use solventorcitrus-based adhesive removers. When

appropriate, follow the Resilient Floor Covering Institute’s (RFCI) Recommended Work Practice for Removal of Existing Floor Covering

and Adhesive. Always wear safety glasses and use respiratory protection or other safeguards to avoid inhaling any dust.The label,

installation, and maintenance instructions along with thetechnical data sheet,limited warranty and anyappropriateSafety Data Sheet

(SDS) of all products must be read, understood, and followed before installation commences. If the substrate or subﬂoor fails for any

reason, then the ﬂoor covering limited warranty is void.

Do not leave spills unattended - wipe up promptly, and allowthe ﬂoor coveringto dry before trafﬁcking.Use bathmats and install safety

handrails where thisﬂoor covering isusednext to wet or barefootareas, like showers and baths.

Documentation:Record and ﬁle the measured and observed site conditions and test results, including all photographs and

correctivemeasures. Maintaining this documentation, along with the original invoice and any labor receipts throughout the warranty

period, is recommended, as this will be required in the unlikely event of a claim.

Site Conditions:The prepared installation area must be fully enclosed and weather tight. During the installation, any direct sunlight

should be blocked using blinds, drapes or other protection. The ambient temperature during installation must be > 60°F (16°C), with a

recommended maximum of 80°F (27°C).

Note: When installing at temperatures > 80°F (27°C), the size of an expansion gap will increase when the ﬂoor covering is cooled.

Flatness: Check all substrates for ﬂatness prior to installation. The maximum acceptable tolerance is < 1/8-in. gap (2 x US quarters)

over 6-ft. and ≤ 1/16-in. gap (1 x US quarter) over 1-ft. Make any necessary adjustments to the substrate before installation.Dormant

cracks, saw cut joints and grout lines < 1/8-in. wide or deep are acceptable – all others must be cleaned of all dirt and debris, then ﬁlled

using a suitable commercial grade patching or repair compound, following the product instructions.

Concrete Subﬂoors: All concrete must be free of contaminates and structurally sound. If required, smooth the surface using a suitable,

moisture-resistant commercial grade leveling or patching compound, following the product instructions. Do not install if hydrostatic

pressure is visible, present or suspected. If a chemical adhesive remover has been used, contact the technical department.

For all on and below grade concrete slabs, test the surface to conﬁrm it is absorbent (porous), following the ASTM F3191 Standard

Practice for Field Determination of Substrate Water Absorption (Porosity) for Substrates to Receive Resilient Flooring. The water

droplets placed on the substrate must be absorbed for it to be considered absorbent. If required, the concrete can be made porous by

mechanical methods, such as diamond grinding, a DiamaBrush buffer attachment, shotblasting or similar.

Concrete Moisture: For all on and below grade concrete slabs, use a ≥ 6-mil thick polyethylene (PE) sheet, available at Lowe’s. Sheeting

must be installed over the entire area and extend at least 2-in. up the walls. All seams must be overlapped and taped according to the

product instructions. The liability and warranty for any product’s performance remains with its manufacturer.

Wood Subﬂoors: All wooden subﬂoors and substrates must be dry and in compliance with the moisture content percent (MC-%) for

your region. Regional values are freely available by searching “moisture map of wood” images. Test using a non-destructive electronic

moisture meter, following the product instructions.

The subﬂoor must comply with local building codes, have at least 18-in. of well-ventilated air space below and have a suitable vapor

retarder to isolate the subﬂoor from ground cover and outdoor conditions. Wood subﬂoors must have a total thickness of at least 1-in.

Sleepers must not make direct contact with concrete or earth. If necessary, install an underlayment grade plywood with a minimum

thickness of 1/4-in. on the surface. The underlayment must be installed in the opposite direction to the subﬂoor, following ASTM F1482

Standard Practice for Installation and Preparation of Panel Type Underlayments to Receive Resilient Flooring.

Note: plywood is a water-sensitive subﬂoor that may become damaged or deformed by topical liquids. To protect wood subﬂoors from

topical water exposure, follow the Wet Area Guidelines below.

Additional Acoustic Underlayments: Additional acoustic underlayments are not recommended or required. However, should one be

used, do not use in commercial areas and ensure a polycarbonate chair mat is used in all rolling chair areas.

Unsuitable Subﬂoors:These include but are not limited to: any ﬂoating or loose ﬂoor coverings, hardwood, carpet, cushion vinyl, rubber,

cork,foam,asphalt tile, any additionalacoustic underlayment, any substrate with visible mold, mildew, or fungi and any substrate in

wet areas, such as inside showers and saunas. Do not install directly over any adhesive or adhesive residue of any kind.Do not install

directly over radiant heated substrate or in recreation vehicles, campers or boats.

Note: Existing hardwood ﬂoor coverings will swell when exposed to moisture: vinyl ﬂoor covering may restrict the movement of moisture

in hardwood, which may result in ﬂooring failure, especially when installed on or below grade. Some hardwood ﬂoor coverings may also

discolor vinyl ﬂoor covering, which is excluded from warranty coverage. By electing to install over any existing ﬂoor covering releases

the manufacturer from any responsibility regarding the suitability and continued performance of that product, including any resulting

effect on the new ﬂoor covering, such as indentations and damaged locking mechanisms.

Other Subﬂoors/Substrates:These may be acceptable. However, they must be and remain dry, without contaminates and be

structurally sound.

Wet Area Guidelines: Some subﬂoors, such as plywood, may be sensitive to and damaged or deformed by topical liquids, such as

water, pet urine and spills. While ProCore Plus is a waterproof product, water-sensitive subﬂoors may require additional protection

to prevent water exposure. When installing ﬂoor covering in wet areas, ensure that bathmats or similar are used where appropriate to

decrease the amount of water that can collect on the surface. Any and all spills should be cleaned up immediately after discovering

them and within 8 hours. Subﬂoor ﬂatness is critical to preventing water migration through seams that may ﬂex or peak due to ft. trafﬁc

and subﬂoor deﬂection - be sure to check ﬂatness and make all necessary adjustments prior to installing.

Water-sensitive substrate must have a ≥ 6-mil thick polyethylene (PE) sheet (available at Lowe’s) installed over the entire area and

extend at least 2-in. up the walls. All seams must be overlapped and taped according to the product instructions. In addition, the area

must be separated from all other rooms using a suitable water-resistant t-molding. Following ﬂooring installation, the plastic sheet

must be trimmed ﬂush with the surface of the ﬂoor covering. Prior to installing wall-base or molding, the required perimeter expansion

gap must be ﬁlled with a 100% silicone caulk, including the wet area side of all t-moldings. Additionally, all door jambs, plumbing and

vertical surfaces that won’t have wall-base or molding installed must be sealed with 100% silicone caulk. Once the entire perimeter has

been ﬁlled or sealed, water-resistant wall-base, moldings or other accessories may be installed. Apply a bead of silicone caulk to the

parts of the wall-base or moldings that will make contact with the surface of the ﬂooring. Ensure all wall base and moldings are attached

to the substrate, wall or wall-base without compression, to allow movement and cleanup any remaining silicone immediately. Do not

anchor wall-base or moldings into or through the ﬂoor covering.

Expansion Gap:If the length or width of the installation area is ≤ 50-ft., an expansion gap of at least 1/4-in. must be created around

the entire perimeter. If the overall length or width is between 50 – 85-ft., then the gap must be increased to 1/2-in. around the entire

perimeter. A maximum of 85-ft. in length or width must not be exceeded. If required, use a suitable trim molding covering the edges by

1/8-in. and allowing a 1/2-in. expansion gap.

For three-season rooms, a gap of at least 1/2-in. around the entire perimeter is required. In addition, the area must be separated from

all other rooms using a suitable trim molding. The maximum of 30-ft. in length or width must not be exceeded.

Note: Areas with very heavy furniture ≥ 800-lb. (363-kg) must be isolated from the rest of the installation with a compatible t-molding

and have ≥ 1/2-in. expansion gap.

General Preparation:It is recommended toremoveall wall-base before ﬂooring installation. Alternately, a quarter round molding

(ﬁxed to the wall or wall-base only) that covers both therequiredexpansion gap and at least 1/8-in. of the ﬂoor covering may be

installed.Undercutall wooden door jambs and the ﬁrst in. of any remaining wall-base (later covered with molding) with an Oscillating

Multi-Tool or hand saw - the height must be the thickness of the ﬂoor coveringplus 1/64-in., which allows the ﬂoor covering to expand

and contract freely, out of sight, with temperature ﬂuctuations (see ﬁgure 1). Steel door jambs should be pattern-scribed, leaving the

required expansion gap. Use a color-coordinated 100% silicone to ﬁll the void. Clean the entire area to be installed using a HEPA-

ﬁltered vacuum.

Before beginning, check and make sure the lot numbers on the packaging match and mix the ﬂoor covering from several boxes to ensure

a random appearance. During the installation, inspect for visible defects, including any damage, gloss, color or shade variations, dirt

and debris in the locking mechanism (remove using a soft brush), as installing it assumes full responsibility. If you have any concerns,

do not install and immediately contact the technical department.

Layout: Follow thedesignordrawings provided or agreed upon by the designer, architect, or end-user. The end joint layout for all

planks should be random - make sure joints are not “stair stepped”. Failure to randomize end joints could weaken the integrity of the

joint system, which may lead to failure. All planks must be at least 8-in. in length and all end seams must staggered by ≥ 8-in. Tiles must

be installed in a brick-bond pattern, offset by 1/2 or 1/3 of the plank.

Cutting:To cut the ﬂoor covering, measure and mark the surface with a pencil, then carefully score the surface a few times on the

mark using a sharp utility knife along the side of a speed square. Snap the plank downwards and complete by cutting the backing from

underneath (see ﬁgure 2). For complicated cuts, such as door jambs, it is recommended to use a jigsaw with a carbide blade following

the product safety instructions.

Installation: Clean the entire area to be installed twice using a HEPA-ﬁltered vacuum. Determine the best wall to start installation

on - typically this would be the longest straight wall with a doorway (if present). Measure the width of the room and, allowing for two

expansion gaps, calculate the width of your last row. If it is less than half the width of the ﬂoor covering, or if a balanced design is

required, than reduce the width of the ﬁrst row accordingly. Use a chalk-line to mark the outside edge of the ﬁrst row on the substrate.

If needed, trim the ﬁrst row (the side without the extended locking mechanism) to ﬁt, accounting for the expansion gap (see ﬁgure 3).

First Row (slide): At the left corner of the starting wall, position the ﬁrst tile or plank ﬂush with the walls. Use the side and end without

the extended locking mechanism against the walls. Place wedge spacers between the ﬂoor covering and wall to maintain the required

expansion gap around the entire perimeter (see ﬁgure 4). Before connecting the second piece, lay it ﬂat on the substrate, adjacent to the

ﬁrst row and lined up with the end of the previous piece. Then, while keeping the joint perfectly in line, slide the second plank into the

ﬁrst, locking the mechanism together (see ﬁgure 5). Complete the ﬁrst row using this method. If there is a doorway, measure, mark and

cut the ﬂooring to make sure the cut edge will be located underneath the door jamb and frame while maintaining the required expansion

gap. A jigsaw should be used for complicated cuts like these. Keeping the installation straight is critical, so check the ﬁrst row using a

chalk line or similar and, as needed, adjust and reinforce the row by adding more wedge spacers. The acceptable straightness tolerance

is within 1/16-in. for lengths over 20-ft. or 1/32 in. for lengths under 20-ft. Complete the following rows starting with a cut piece, such

as a piece from a previous row. Install the side joints before the end joints as instructed under “Side Joints” and “End Joints”.

Side Joints (angle-angle): Starting at the left corner, place the side without the extended locking mechanism into the side of the

previously installed row at a ∼ 25° angle (see ﬁgure 6). Make sure the joint is seated properly, then slide the plank or tile into position

(see ﬁgure 7). The end joint must line up perfectly. Lay the tile or plank ﬂat and complete the end joint.

End Joints (drop-lock): Always check the alignment of the end joint and adjust if necessary. Lock the joint into place by lightly tap

along the high side, starting from the “T”, using a 1-lb. (∼ 16-oz.) soft faced dead blow hammer or rubber mallet (see ﬁgure 8). Keep the

striking head ﬂat with the ﬂoor covering and tap until perfectly ﬂush. If the locking mechanism does not line up properly, then check and

adjust the straightness as necessary.

Pro-Tips: Do not hit the locking mechanism directly with any hammer, tapping block or pull bar (except the last row) - doing so will

damage the locking mechanism and may result in peaking, gapping or broken joints. If required, use a ∼ 6-in. piece of scrap ﬂoor

covering, seated in the locking mechanism, to lightly tap and close any joints.

If you need to install small cuts of ﬂoor covering that are < 3-in. in length or width, place a thin bead of liquid super-glue on the

previously installed locking mechanism just before installing. This will ensure the pieces remain locked together during use. Do not get

the adhesive on the surface - coverage will be ∼ 30 ft. per oz.

After the ﬁrst ﬁve or six rows are completed, turn around and continue installing, working on top of the installed material. This will allow

the side joints to be pulled together rather than pushed together, which will make the installation even easier.

If you need to disengage the end joints for any reason, ﬁrst unlock the side joints by lifting the outside edge of the row to ∼ 25° and

disconnect the entire row. Make sure all pieces are lying ﬂat and are properly engaged (tap to engage, if required), then simply slide

them apart. If they are angled or pulled upwards, the joint will break.

Completion: If used, plastic sheeting must be trimmed ﬂush with the surface of the ﬂoor covering. If installed in a wet area, plastic

sheeting must be trimmed ﬂush with the subﬂoor. When installing in wet areas, ensure the expansion gap and all vertical surfaces

are ﬁlled or sealed with a 100% silicone caulk and ensure all wall-base and moldings are water-resistant, following to the Wet Area

Guidelines. Install all necessary wall-base and/or moldings and ensure they are anchored to the substrate, wall or wall-base without

compression, to allow movement. Do not anchor wall-base or moldings into or through the ﬂoor covering.

Protection: If required, protect the clean ﬂoor covering from other trades or heavy loads using ½-in. plywood or similar and tape all

seams. For light trafﬁc, use Ram board or similar and tape all seams. For furniture, use only polyurethane, silicon or felt glides (replaced

> 3-times a year), keeping them clean and grit-free – all glides should be ≥ 1-in.2, especially on heavy furniture. Use protective chair

mats designed for resilient ﬂooring underneath rolling chairs or soft “W-type” wheels. Failure to observe these requirements could

result in joint damage or failure. Use non-rubber-backed entrance matting at all outdoor entrances, as this will improve air quality and

reduce maintenance. Do not drag heavy or sharp objects directlyacross the surface - use hard surface “sliders” (available at Lowe’s). For

areas that may be subjected to standing water on the surface, such as bathrooms with a bath or shower, theperimeterof the installation

must be properly sealed using a 100% silicon caulk to prevent water from getting beneath the ﬂooring. To avoid excessive fading or

discoloration from direct sunlight exposure, use appropriate window treatments, an effective UV/IR ﬁlm or Low-E glass windows. Take

photographs and have any required documentation signed and ﬁled following completion.

PROCORE® 3-IN-1 TRIM MOLDING

General Information: If the overall length of the area is over 85-ft. in either direction, if temperatures are expected to exceed 90°F

(32°C), like in 3-season rooms, or if a transition is desired, a 3-In-1 trim molding should be installed. 3-in-1 trim moldings are color-

coordinated and available at Lowe’s.

Note: Colors and patterns that have a high color variance won’t match perfectly.

Figure 1 - General Prep - Undercut Door Jambs

Figure 3 - Installation - Score & Trim Plank

Figure 2 - Cutting - Snap Plank After Scoring

Figure 4 - First Row - Place Spacers In Perimeter Gap

Figure 5 - First Row - Slide Planks Together Figure 6 - Side Joints - Angle Plank & Slide Into Place

Figure 7 -End Joints - Align With Adjacent Plank Figure 6 - End Joints - Lock Into Place With Mallet

INSTALLATION INSTRUCTION FIGURES

ProCore Plus LWD8053RCB Installation guide

Brand: ProCore Plus

Model: LWD8053RCB

Type: Installation guide

This manual is also suitable for

Download PDF

report

ProCore Plus LWD8053RCB Installation guide

This manual is also suitable for

ProCore Plus LWD8053RCB Installation guide

Related papers

Other documents