Behringer FEX800 Quick start guide

Behringer
Brand
Behringer
Model
FEX800
Category
Supplementary music equipment
Type
Quick start guide

This manual is also suitable for

Quick Start Guide (Check out behringer.com for FullManual)
MINIFEX FEX800
Ultra-Compact Stereo Multi-FX Processor
LEGAL DISCLAIMER
LIMITED WARRANTY
Important Safety
Instructions
Terminals marked with this
symbol carry electrical
current of su cient
magnitude to constitute risk of electric
shock. Use only high-quality professional
speaker cables with ¼" TS or twist-
locking plugs pre-installed. Allother
installation or modi cation should be
performed only by quali edpersonnel.
This symbol, wherever it
appears, alerts you to the
presence of uninsulated
dangerous voltage inside the enclosure -
voltage that may be su cient to
constitute a risk ofshock.
This symbol, wherever it
appears, alerts you to
important operating and
maintenance instructions in the
accompanying literature. Please read
themanual.
Caution
To reduce the risk of electric
shock, do not remove the
top cover (or the rear section). No user
serviceable parts inside. Refer servicing
to quali edpersonnel.
Caution
To reduce the risk of  re or
electric shock, do not expose
this appliance to rain and moisture.
Theapparatus shall not be exposed to
dripping or splashing liquids and no
objects  lled with liquids, such as vases,
shall be placed on the apparatus.
Caution
These service instructions
are for use by quali ed
service personnel only. Toreduce the
risk of electric shock do not perform any
servicing other than that contained in the
operation instructions. Repairshave to be
performed by quali ed servicepersonnel.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus
nearwater.
6. Clean only with dry cloth.
7. Do not block any ventilation
openings. Install in accordance with the
manufacturer’s instructions.
8. Do not install near any heat sources
such as radiators, heat registers, stoves,
orother apparatus (including ampli ers)
thatproduceheat.
9. Do not defeat the safety purpose
of the polarized or grounding-type plug.
Apolarized plug has two blades with
one wider than the other. A grounding-
type plug has two blades and a third
grounding prong. The wide blade or the
third prong are provided for your safety.
Ifthe provided plug does not  t into
your outlet, consult an electrician for
replacement of the obsoleteoutlet.
10. Protect the power cord from being
walked on or pinched particularly at
plugs, convenience receptacles, and the
point where they exit from theapparatus.
11. Use only attachments/accessories
speci ed by themanufacturer.
12. Use only with
the cart, stand,
tripod, bracket,
ortable speci ed by
the manufacturer,
orsold with
the apparatus. When a cart is used,
usecaution when moving the cart/
apparatus combination to avoid injury
from tip-over.
13. Unplug this apparatus during
lightning storms or when unused for long
periods oftime.
14. Refer all servicing to quali ed
service personnel. Servicing is required
when the apparatus has been damaged
in any way, such as power supply cord or
plug is damaged, liquid has been spilled
or objects have fallen into the apparatus,
the apparatus has been exposed to rain
or moisture, does not operate normally,
orhas beendropped.
15. The apparatus shall be connected to
a MAINS socket outlet with a protective
earthingconnection.
16. Where the MAINS plug or an
appliance coupler is used as the
disconnect device, thedisconnect device
shall remain readilyoperable.
TECHNICAL SPECIFICATIONS AND
APPEARANCES ARE SUBJECT TO CHANGE
WITHOUT NOTICE AND ACCURACY
IS NOT GUARANTEED. BEHRINGER,
KLARKTEKNIK, MIDAS, BUGERA,
AND TURBOSOUND ARE PART OF THE
MUSIC GROUP MUSICGROUP.COM.
ALL TRADEMARKS ARE THE PROPERTY
OF THEIR RESPECTIVE OWNERS.
MUSICGROUP ACCEPTS NO LIABILITY
FOR ANY LOSS WHICH MAY BE
SUFFERED BY ANY PERSON WHO RELIES
EITHER WHOLLY OR IN PART UPON
ANY DESCRIPTION, PHOTOGRAPH
OR STATEMENT CONTAINED HEREIN.
COLORSAND SPECIFICATIONS MAY
VARY FROM ACTUAL PRODUCT.
MUSIC GROUP PRODUCTS ARE SOLD
THROUGH AUTHORIZED FULLFILLERS
AND RESELLERS ONLY. FULLFILLERS
AND RESELLERS ARE NOT AGENTS OF
MUSICGROUP AND HAVE ABSOLUTELY
NO AUTHORITY TO BIND MUSICGROUP
BY ANY EXPRESS OR IMPLIED
UNDERTAKING OR REPRESENTATION.
THIS MANUAL IS COPYRIGHTED.
NO PART OF THIS MANUAL MAY BE
REPRODUCED OR TRANSMITTED IN ANY
FORM OR BY ANY MEANS, ELECTRONIC
OR MECHANICAL, INCLUDING
PHOTOCOPYING AND RECORDING OF
ANY KIND, FORANY PURPOSE, WITHOUT
THE EXPRESS WRITTEN PERMISSION OF
MUSICGROUPIPLTD.
ALL RIGHTS RESERVED.
© 2013 MUSICGroupIPLtd.
Trident Chambers, Wickhams Cay,
P.O. Box 146, Road Town, Tortola,
BritishVirgin Islands
For the applicable warranty
terms and conditions and
additional information regarding
MUSICGroup’s Limited Warranty,
please see complete details online at
www.music-group.com/warranty.
Las terminales marcadas con
este símbolo transportan
corriente eléctrica de
magnitud su ciente como para constituir
un riesgo de descarga eléctrica.
Utilicesolo cables de altavoz
profesionales y de alta calidad con
conectores TS de 6,3 mm o de bayoneta
pre jados. Cualquier otra instalación o
modi cación debe ser realizada
únicamente por un técnicocuali cado.
Este símbolo, siempre que
aparece, leadvierte de la
presencia de voltaje
peligroso sin aislar dentro de la caja;
estevoltaje puede ser su ciente para
constituir un riesgo dedescarga.
Este símbolo, siempre que
aparece, leadvierte sobre
instrucciones operativas y
de mantenimiento que aparecen en la
documentación adjunta. Por favor,
leaelmanual.
Atención
Para reducir el riesgo de
descarga eléctrica, no quite
la tapa (olaparte posterior). Nohay
piezas en el interior del equipo que
puedan ser reparadas por el usuario.
Sies necesario, póngase en contacto con
personal cuali cado.
Atención
Para reducir el riesgo
de incendio o descarga
eléctrica, no exponga este aparato a la
lluvia, humedad o alguna otra fuente que
pueda salpicar o derramar algún líquido
sobre el aparato. Nocoloque ningún
tipo de recipiente para líquidos sobre
elaparato.
Atención
Las instrucciones de servicio
deben llevarlas a cabo
exclusivamente personal cuali cado.
Paraevitar el riesgo de una descarga
eléctrica, no realice reparaciones que no
se encuentren descritas en el manual
de operaciones. Lasreparaciones deben
ser realizadas exclusivamente por
personalcuali cado.
1. Lea las instrucciones.
2. Conserve estas instrucciones.
3. Preste atención a todas
lasadvertencias.
4. Siga todas las instrucciones.
5. No use este aparato cerca del agua.
6. Limpie este aparato con un pañoseco.
7. No bloquee las aberturas de
ventilación. Instale el equipo de acuerdo
con las instrucciones del fabricante.
8. No instale este equipo cerca de
fuentes de calor tales como radiadores,
acumuladores de calor, estufas u otros
aparatos (incluyendo ampli cadores)
quepuedan producir calor.
9. No elimine o deshabilite nunca la
conexión a tierra del aparato o del cable
de alimentación de corriente. Unenchufe
polarizado tiene dos polos, uno de los
cuales tiene un contacto más ancho que
el otro. Una clavija con puesta a tierra
dispone de tres contactos: dos polos y
la puesta a tierra. El contacto ancho y el
tercer contacto, respectivamente, son
los que garantizan una mayor seguridad.
Siel enchufe suministrado con el equipo
no concuerda con la toma de corriente,
consulte con un electricista para cambiar
la toma de corriente obsoleta.
10. Coloque el cable de suministro de
energía de manera que no pueda ser
pisado y que esté protegido de objetos
a lados. Asegúrese de que el cable de
suministro de energía esté protegido,
especialmente en la zona de la clavija y en
el punto donde sale del aparato.
11. Use únicamente los dispositivos o
accesorios especi cados por elfabricante.
12. Use
únicamente
la carretilla,
plataforma, trípode,
soporte o mesa
especi cados por
el fabricante o suministrados junto
con el equipo. Altransportar el equipo,
tengacuidado para evitar daños y caídas
al tropezar con algúnobstáculo.
13. Desenchufe el equipo durante
tormentas o si no va a utilizarlo durante
un periodo largo.
14. Confíe las reparaciones únicamente
a servicios técnicos cuali cados.
Launidad requiere mantenimiento
siempre que haya sufrido algún daño,
si el cable de suministro de energía o el
enchufe presentaran daños, sehubiera
derramado un líquido o hubieran caído
objetos dentro del equipo, si el aparato
hubiera estado expuesto a la humedad
o la lluvia, si ha dejado de funcionar de
manera normal o si ha sufrido algún
golpe o caída.
15. Al conectar la unidad a la toma de
corriente eléctrica asegúrese de que la
conexión disponga de una unión a tierra.
16. Si el enchufe o conector de red sirve
como único medio de desconexión, éste
debe ser accesiblefácilmente.
LAS ESPECIFICACIONES TÉCNICAS Y LA
APARIENCIA EXTERIOR ESTÁN SUJETAS
A CAMBIOS SIN PREVIO AVISO Y NO
PODEMOS GARANTIZAR LA TOTAL
EXACTITUD DE TODO LO QUE APARECE
AQUÍ. BEHRINGER, KLARK TEKNIK,
MIDAS, BUGERA, YTURBOSOUND
SON PARTE DEL GRUPOMUSIC GROUP
MUSICGROUP.COM. TODAS LAS
MARCAS REGISTRADAS SON PROPIEDAD
DE SUS RESPECTIVOS DUEÑOS.
MUSICGROUP NO ACEPTA NINGÚN TIPO
DE RESPONSABILIDAD POR POSIBLES
Instrucciones de
seguridad
NEGACIÓN LEGAL
2 3Quick Start GuideMINIFEX FEX800
Page is loading ...
Page is loading ...
(EN) Controls
MINIFEX FEX800 Controls
8 MINIFEX FEX800 9 Quick Start Guide
(2)
(1)
(8)
(3) (4) (5) (6) (7) (9) (10)
(11) (12) (14)(13)
(1) The two LED displays show the eect preset currently selected.
One LED is assigned to each preset.
(2) Use the PRESETS control to select one of the 16 eect presets.
(3) The EDIT control allows you to edit one eect parameter.
Thecenter position corresponds to the default setting
programmed for the preset.
(4) The TAP/SELECT button performs two functions:
• TAP (tempo entry): Hit the button several times in
the tempo of the music piece to adapt the delay time of
presets 9 and 15 or the modulation speed of presets 10-12.
The button starts ashing in the corresponding tempo.
• SELECT (additional eect parameter):
Pressthisbutton to choose between two dierent
eect characteristics when using presets 1-8,
13-14,16. Whenthe button lights up this means that
the corresponding parameter of the selected preset
hasbeenactivated.
(5) Use the INPUT LEVEL control to adjust the input signal level.
Please be sure to set a level that is suciently high but does not
overload the unit.
(6) The L + R LED display is for monitoring the input level.
Itcomprises 6 LEDs. When the CLIP LED lights up, this indicates
that digital distortion may occur at the input of the FEX800.
Inthis case, the input signal level must bereduced.
(7) Use the MIX BALANCE control to adjust the ratio of original
vs.eect signal. Turn the control fully to the right to hear only
the processed eect signal. Turn it fully to the left to hear only
the unprocessed input signal.
(8) The IN/OUT button enables/disables the eect signal.
Thebutton lights up when the input signal is being processed
by the FEX800. In order to hear the processed signal you have
toset a suitable ratio of eect vs. direct signal using the
MIXBALANCE control (7).
(9) Use the OUTPUT LEVEL control to adjust the output level.
(10) The � switch turns your MINIFEX FEX800 on and o. The switch
lights up when the unit is switched on.
(11) The FEX800 is connected to the mains using a 2-pole
POWERconnector jack. A matching mains adaptor is
includedwith the unit.
(12) A single footswitch can be connected to the IN/OUT connector.
Thisfootswitch allows you to remotely control the IN/OUT
button (8) on the front panel and switch the eect signal
onando.
(13) The two OUTPUT connectors are on ¼" connectors and provide
a balanced left/right signal.
(14) The two INPUT connectors are on ¼" connectors and can be
used for unbalanced signals. A single mono signal should be
connected to the L jack.
Check Out behringer.com for Full Manual
Front panel control elements of the FEX800 Rear panel connectors of the FEX800
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Specications Especicaciones técnicas
18 19Quick Start GuideMINIFEX FEX800
Input
Type ¼" TS connectors, unbalanced
Impedance approx. 30 kΩ
Output
Type ¼" TRS connectors, impedance balanced
Impedance approx. 220 Ω
Max. output level +10 dBu
In/Out
Type ¼" TS footswitch connector
Digital Processing
Converters 24-Bit Delta-Sigma, 128-times oversampling
Sampling rate 48 kHz
System Specications
Frequency response 10 Hz to 22 kHz, -3 dB
Dynamic range 96 dB, 10 Hz to 22 kHz
Distortion 0,01% typ. @ 0 dBFS
Crosstalk -75 dB @ 1 kHz
Signal-to-noise ratio 10 Hz to 22 kHz <86 dB @ 0 dBu, A-weighted
Power Supply
Mains connection external power supply, 9 V~, 750 mA
Mains Voltage
USA/Canada 120 V~, 60 Hz
U.K./Australia 240 V~, 50 Hz
China 220 V~, 50 Hz
Europe 230 V~, 50 Hz
Japan 100 V~, 50 - 60 Hz
Power consumption approx. 7.5 W
Dimensions/Weight
Dimensions (H x W x D)
approx. 1.9 x 4.7 x 9.6"
approx. 48 x 120 x 242.6 mm
Weight approx. 1.46 lbs / 0.66 kg
Conectores jack mono de 6,3 mm, no balanceados
Impedancia de entrada aprox. 30 kΩ
Salida (Output)
Conectores jack estéreo de 6,3 mm, balanceados
Impedancia de salida mín. 220 Ω
Nivel de salida máx. +10 dBu
In/Out
Conector jack mono de 6,3 mm (pedal)
Procesamiento Digital
Convertidor Delta-Sigma de 24 bits, sobremuestreo de 128x
Frecuencia de muestreo 48 kHz
Datos de Sistema
Respuesta en frecuencia 10 Hz a 22 kHz, - 3 dB
Dinámica 96 dB, 10 Hz a 22 kHz
THD 0,01% típ. @ 0 dBFS
Diafonía -75 dB @ 1 kHz
Relación señal a ruido 10 Hz a 22 kHz <86 dB @ 0 dBu, ponderado A
Suministro de Corriente
Conexión de red adaptador de corriente externo, 9 V~, 750 mA
Tensión de Red
EE.UU./Canadá 120 V~, 60 Hz
R.U./Australia 240 V~, 50 Hz
China 220 V~, 50 Hz
Europa 230 V~, 50 Hz
Japón 100 V~, 50 - 60 Hz
Consumo de potencia aprox. 7,5 W
Dimensiones/Peso
Dimensiones (alt. x anch. x prof.) aprox. 48 x 120 x 242,6 mm
Peso aprox. 0,66 kg
Entrada (Input)
Page is loading ...
Page is loading ...
Other important information
1. Register online. Pleaseregister
your new MUSIC Group equipment
right after you purchase it by visiting
behringer. com. Registeringyour purchase
using our simple online form helps us to
process your repair claims more quickly
and eciently. Also, read the terms and
conditions of our warranty, ifapplicable.
2. Malfunction. Should your
MUSICGroup Authorized Reseller not be
located in your vicinity, you may contact
the MUSIC Group Authorized Fulller for
your country listed under “Support” at
behringer. com. Shouldyour country not be
listed, pleasecheck if your problem can be
dealt with by our “OnlineSupport” which
may also be found under “Support” at
behringer. com. Alternatively, please submit
an online warranty claim at behringer. com
BEFORE returning theproduct.
3. Power Connections.
Beforeplugging the unit into a power
socket, please make sure you are using the
correct mains voltage for your particular
model. Faulty fuses must be replaced
with fuses of the same type and rating
withoutexception.
1. Registro online.
Lerecomendamos que registre su nuevo
aparato MUSIC Group justo después de
su compra accediendo a la página web
behringer. com. Elregistro de su compra a
través de nuestro sencillo sistema online
nos ayudará a resolver cualquier incidencia
que se presente a la mayor brevedad
posible. Además,aproveche para leer
los términos y condiciones de nuestra
garantía, siesaplicable en sucaso.
2. Averías. En el caso de que no
exista un distribuidor MUSIC Group en
las inmediaciones, puede ponerse en
contacto con el distribuidor MUSIC Group
de su país, queencontrará dentro del
apartado “Support” de nuestra página web
behringer. com. En caso de que su país no
aparezca en ese listado, acceda a la sección
“Online Support” (quetambiénencontrará
dentro del apartado “Support” de nuestra
páginaweb) y compruebe si su problema
aparece descrito y solucionado allí.
Deforma alternativa, envíenos a través
de la página web una solicitud online de
soporte en periodo de garantía ANTES de
devolvernoselaparato.
3. Conexiones de corriente.
Antes de enchufar este aparato a una salida
de corriente, asegúrese de que dicha salida
sea del voltaje adecuado para su modelo
concreto. En caso de que deba sustituir un
fusible quemado, deberáhacerlo por otro de
idénticas especicaciones, sinexcepción.
1. Enregistrez-vous enligne.
Prenezle temps d’enregistrer votre
produit MUSIC Group aussi vite que
possible sur le site Internet behringer. com.
Lefait d’enregistrer le produit en ligne
nous permet de gérer les réparations
plus rapidement et plus ecacement.
Prenezégalement le temps de lire les
termes et conditions de notregarantie.
2. Dysfonctionnement. Si vous
n’avez pas de revendeur MUSIC Group près
de chez vous, contactez le distributeur
MUSIC Group de votre pays: consultez la
liste des distributeurs de votre pays dans
la page “Support” de notre site Internet
behringer. com. Si votre pays n’est pas
dans la liste, essayez de résoudre votre
problème avec notre “aideen ligne”
que vous trouverez également dans la
section “Support” du site behringer. com.
Vouspouvez également nous faire parvenir
directement votre demande de réparation
sous garantie par Internet sur le site
behringer. com AVANT de nous renvoyer
leproduit.
3. Raccordement au secteur.
Avant de relier cet équipement au secteur,
assurez-vous que la tension secteur de
votre région soit compatible avec l’appareil.
Veillez à remplacer les fusibles uniquement
par des modèles exactement de même
taille et de même valeur électrique — sans
aucuneexception.
Important information
Aspectos importantes
Informations
importantes
1. Online registrieren.
Bitteregistrieren Sie Ihr neues
MUSICGroup-Gerät direkt nach dem Kauf
auf der Website behringer. com. WennSie
Ihren Kauf mit unserem einfachen online
Formular registrieren, könnenwir Ihre
Reparaturansprüche schneller und
ezienter bearbeiten. Lesen Sie bitte
auch unsere Garantiebedingungen,
fallszutreend.
2. Funktionsfehler. Sollte sich
kein MUSIC Group Händler in Ihrer Nähe
benden, können Sie den MUSIC Group
Vertrieb Ihres Landes kontaktieren, der auf
behringer. com unter „Support“ aufgeführt
ist. Sollte Ihr Land nicht aufgelistet sein,
prüfen Sie bitte, ob Ihr Problem von
unserem „Online Support“ gelöst werden
kann, den Sie ebenfalls auf behringer. com
unter „Support“ nden. Alternativ reichen
Sie bitte Ihren Garantieanspruch online
auf behringer. com ein, BEVOR Sie das
Produktzurücksenden.
3. Stromanschluss. Bevor Sie das
Gerät an eine Netzsteckdose anschließen,
prüfen Sie bitte, obSie die korrekte
Netzspannung für Ihr spezielles Modell
verwenden. Fehlerhafte Sicherungen
müssen ausnahmslos durch Sicherungen
des gleichen Typs und Nennwerts
ersetztwerden.
1. Registre-se online. Porfavor,
registreseu novo equipamento
MUSICGroup logo após a compra visitando
o site behringer. com Registrar sua compra
usando nosso simples formulário online
nos ajuda a processar seus pedidos de
reparos com maior rapidez e eciência.
Além disso, leia nossos termos e condições
de garantia, caso sejanecessário.
2. Funcionamento Defeituoso.
Casoseufornecedor MUSIC Group não esteja
localizado nas proximidades, vocêpode
contatar um distribuidor MUSICGroup
para o seu país listado abaixo de “Suporte”
embehringer. com. Se seu país não estiver
na lista, favor checar se seu problema pode
ser resolvido com o nosso “SuporteOnline”
que também pode ser achado abaixo
de “Suporte”em behringer. com.
Alternativamente, favorenviar uma
solicitação de garantia online em
behringer. com ANTES da devolução
doproduto.
3. Ligações. Antes de ligar a unidade
à tomada, assegure-se de que está a
utilizar a voltagem correcta para o modelo
em questão. Osfusíveis com defeito
terão de ser substituídos, sem qualquer
excepção, porfusíveis do mesmo tipo e
correntenominal.
Weitere wichtige
Informationen
Outras Informações
Importantes
25Quick Start Guide24 MINIFEX FEX800
FEDERAL COMMUNICATIONS
COMMISSION COMPLIANCE
INFORMATION
Responsible Party Name: MUSIC Group Services USInc.
Address: 18912 North Creek Parkway,
Suite 200 Bothell, WA 98011, USA
Phone/Fax No.: Phone: +1 425 672 0816
Fax: +1 425 673 7647
MINIFEX FEX800
complies with the FCC rules as mentioned in the followingparagraph:
This equipment has been tested and found to comply with the limits
for a ClassB digital device, pursuant to part 15 of the FCC Rules.
Theselimits are designed to provide reasonable protection against
harmful interference in a residential installation. Thisequipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
Ifthis equipment does cause harmful interference to radio or television
reception, whichcan be determined by turning the equipment o and
on, theuser is encouraged to try to correct the interference by one or
more of the followingmeasures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that
to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician forhelp.
This device complies with Part 15 of the FCC rules. Operation is subject
to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
includinginterference that may cause undesired operation.
Important information:
Changes or modications to the equipment not expressly approved by
MUSIC Group can void the user’s authority to use the equipment.
MINIFEX FEX800
27Quick Start Guide26 MINIFEX FEX800
We Hear You
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15

Behringer FEX800 Quick start guide

Behringer
Brand
Behringer
Model
FEX800
Category
Supplementary music equipment
Type
Quick start guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents