Deagostini Ford GT User guide

16

STAGE PAGE

66 The rear right wheel hub 254

67 The left rear wheel 258

68 The left rear wheel 260

69 The left rear tyre 262

70 The left rear brake 264

Published in the UK by De Agostini UK Ltd, Royds Withy King, 65 Carter Lane, London EC4V 5EQ.

Published in the USA by De Agostini Publishing USA, Inc., 299 Park Avenue • New York, New York 10171.

Warning: Not suitable for children under the age of 14.

is product is not a toy and is not designed or intended for use in play.

Items may vary from those shown.

254

FORD GT

FD02

FD08

YOUR PARTS

66-A 66-B

66-C

66-D

66-E

66-F

66-G

66-A Disc brake 1

66-B Disc brake 2

66-C Hub

66-D Brake caliper

66-E Drive shaft

66-F Drive shaft joint

66-G Pin

66-H Screw FD02 2.3 x 4mm

66-I Screw FD08 2.3 x 4mm

Stage 66:

The rear right wheel hub

STEP BY STEP

255

STEP 66-1

Insert the three pins

of disc brake 1 (66A)

into the corresponding

holes in disc brake 2

(66B) and press the

two parts together.

STEP 66-3

Insert the smooth end of the pin (66G)

into one of the side holes in the drive

shaft (66E). Push the pin through the

joint and back into the shaft, securing

the parts together.

STEP 66-2

Place the end of the drive shaft

(66E) over the end of the drive

shaft joint (66F). Align the

corresponding holes.

Pins

66-B

66-A

66-G

66-F

66-E

66-G

256

FORD GT

66-B

STEP 66-4

Place the disc brake assembly onto

the wheel hub (66C), as shown.

STEP 66-6

Insert the drive shaft joint

(66F) into its the hole in the

centre of the wheel hub.

STEP 66-5

Place the brake caliper (66D)

onto the wheel hub, it can only

t in one orientation. Secure

the caliper with an FD08 screw

in the left hole.

FD08

66-C

66-A

66-E

66-F

66-B

66-D

STEP BY STEP

257

STEP 66-7

Take the wheel from

Stage 65 and place the

wheel hub assembly

onto the post on the

inside of the wheel. A

notch in the brake disk

aligns with the post in

the centre of the wheel.

STEP 66-8

Turn the wheel over and secure

the wheel hub with an FD02

screw. Retrieve the wing nut

from Stage 65 and press-t it

over the screw, as shown

STAGE COMPLETE

Notch

Post

FD02

258

FORD GT

67-A Wheel outer

67-B Wheel wing nut

YOUR PARTS

67-A

67-B

Stage 67:

The left rear wheel

STEP BY STEP

259

STEP 67-1

Carefully store the wheel outer (67A) and

wing nut (67B) received with this stage for

later use.

STAGE COMPLETE

260

FORD GT

YOUR PARTS

68-A Wheel inner

68-B Wheel centre

68-A

68-B

Stage 68:

The left rear wheel

STEP BY STEP

261

STEP 68-3

Bring the two parts of

the wheel together.

STEP 68-2

Align the holes of the wheel

centre (68B) with the pins of

the wheel outer (67A).

STEP 68-1

Retrieve the wheel

outer (67A) supplied

with Stage 67.

67-A

68-B

67-A

Hole

262

FORD GT

69-A Left rear tyre

YOUR PARTS

69-A

Stage 69:

The left rear tyre

STEP BY STEP

263

STEP 69-2

Fit the left rear wheel into the

tyre (69-A) following the same

process as described with the

other tyres.

STEP 69-1

Prepare the left rear wheel

assembly from the previous stage.

STAGE COMPLETE

264

FORD GT

FD02

FD08

YOUR PARTS

70-A 70-B

70-C

70-D

70-E

70-F

70-G

70-A Disc brake 1

70-B Disc brake 2

70-C Hub

70-D Brake caliper

70-E Drive shaft

70-F Drive shaft joint

70-G Pin

70-H Screw FD02 2.3 x 4mm

70-I FD08 2.3 x 4mm

Stage 70:

The left rear brake

STEP BY STEP

265

STEP 70-1

Insert the three pins of

disc brake 1 (70A) into

the corresponding holes

in disc brake 2 (70B)

and press the two

parts together.

STEP 70-3

Insert the smooth end of the pin (70G)

into one of the side holes in the drive

shaft (70E). Push the pin through the

joint and back into the shaft, securing

the parts together.

STEP 70-2

Place the end of the drive shaft

(70E) over the end of the drive

shaft joint (70F). Align the

corresponding holes.

Pins

70-B

70-A

70-G

70-F

70-E

70-G

266

FORD GT

70-B

STEP 70-4

Place the disc brake assembly onto

the wheel hub (70C), as shown.

STEP 70-6

Collect the wheel assembled in the

previous stage, and place the wheel

hub assembly onto the post on the

inside of the wheel. A notch in the

brake disk aligns with the post in

the centre of the wheel.

STEP 70-5

Place the brake caliper (70D)

onto the wheel hub, it can only

t in one orientation. Secure

the caliper with an FD08 screw

in the right hole.

FD08

70-C

70-A

70-B

70-D

Notch

Post

STEP BY STEP

267

STEP 70-7

Insert the drive shaft joint

(70F) into its the hole in the

centre of the wheel hub.

STEP 70-8

Turn the wheel over and secure

the wheel hub with an FD02

screw. Retrieve the wing nut

from Stage 67 and press-t it

over the screw, as shown

STAGE COMPLETE

FD02

70-C

70-E

70-F

Deagostini Ford GT User guide

Deagostini Ford GT User guide

Related papers

Other documents