333
Thank you for buying a NorthQ product. Our devices gives you and
your family the opportunity to experience a new way of living.
This user manual helps you to get Q-Stick installed.
• Your Wi-Fi router must support the 802.11N standard in
order to install Q-Stick. By far most routers do so. You can
find this information in the manual that comes with your
router (or by searching online).
• Your router must not use WEP security. We recommend
WPA2-PSK for security purposes. You can find this
information in the manual that comes with your router (or by
searching online).
• The installation can be performed using PC, Tablet or Smart
Phone.
Welcome
5
Q-Stick Setup
5
The Q-Stick connects the Q-Power, Q-Gas, Danfoss Living
Connect, Q-Plug and other devices to your HomeManager
account.
You have to setup the Q-Stick before installing any other
NorthQ or other Z-Wave devices.
Upon powering up, make sure the Q-Stick LED flashes blue
once to indicate that it is powered on. Place it in the middle
of the home in order to obtain the best wireless coverage.
The wireless range is 10-20 meter in houses, but can vary
depending on the building construction.
Power it up with the wall plug
Alternatively, use the extension chord
1
2
1
Before connecting to the Q-Stick go to Wi-Fi settings and click
on the forget network option for your home network so that
it will not auto connect to your existing Wi-Fi while installing
the Q-Stick.
6
Q-Stick Setup
The Q-Stick will now be listed as NorthQ Gateway_XXXX
(where XXXX are the last 4 digits of the Q-Stick serial number)
under Wi-Fi settings. Now connect to the NorthQ Gateway_
XXXX and the install page shown to the right will appear.
1
iOS and Windows Mobile Users- the setup page should
appear automatically. Otherwise, open a browser and enter
the address http://192.168.0.1
Computer Users - open a browser and enter the address
http://192.168.0.1 . The setup page should appear. If it doesn’t
happen refresh the page or try with another Internet browser.
Android Users - a notification should appear in a couple of
seconds asking you to sign in to the network. Click on the
notification. Otherwise, open a browser and enter the address
http://192.168.0.1
Click Install to proceed.
3
13
HomeManager Account Creation
Fill out your House Budget
Enter currency in 3 letters code (eg. EUR)
Click on Save
Enter kWh price
11
12
13
14
Follow these steps only if you have a Q-Plug and/or a
Q-Power. Otherwise, click on Skip.
The House Budget is used for prediction and “spendings
comparison”. You should enter the budget amount including
taxes/VAT (per your utility bill). For example, you could enter
your last year budget amount including taxes/VAT (per your
utility bill).
WELL DONE!
Your HomeManager account is set up and ready!
2
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
Winmate W10FA3S-PCH2AC-PoE Quick start guide
-
Winmate W07FA3S-PCM1-PoE Quick start guide
-
Comelit simplehome Technical Manual
-
Winmate W10FA3S-EHH2 Quick start guide
-
Winmate R15FA3S-PTC3 Quick start guide
-
Winmate R15FA3S-GSC3 Quick start guide
-
Winmate W07FA3S-PCM1-PoE Quick start guide
-
Winmate W10FA3S-EHH2 Quick start guide
-
Winmate R10FA3S-GCT2 Quick start guide
-
Winmate W10FA3S-EHH2 Quick start guide
