Greenlee PVA0021, PVA0022 Hydraulic Control Valves User manual

INSTRUCTION MANUAL

Read and understand all of the instructions and

safety information in this manual before operating

or servicing this tool.

Register this product at www.greenlee.com

PVA0021 • PVA0022

Hydraulic Control Valves

PVA0021 • PVA0022

Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

2

Safety

Safety is essential in the use and maintenance of

Greenlee Utility tools and equipment. This instruction

manual and any markings on the tool provide informa-

tion for avoiding hazards and unsafe practices related to

the use of this tool. Observe all of the safety information

provided.

Purpose of this Manual

This manual is intended to familiarize all personnel with

the safe operation and maintenance procedures for the

following Greenlee Utility valves:

PVA0021 (42948)

PVA0022 (42949)

Keep this manual available to all personnel.

Replacement manuals are available upon request

at no charge at www.greenlee.com.

Other Publications

Tool Owners/Users

SAE Standard J1273 (Hose and Hose Assemblies):

Publication 99930323

Greenlee Utility Authorized Service Centers

Service Manual: Publication 99912872

All specications are nominal and may change as design

improvements occur. Greenlee Textron Inc. shall not be liable for

damages resulting from misapplication or misuse of its products.

KEEP THIS MANUAL

Table of Contents

Description .................................................................... 2

Safety ............................................................................ 2

Purpose of this Manual ................................................. 2

Other Publications ......................................................... 2

Important Safety Information ..................................... 3-5

Identication .................................................................. 6

Specications ............................................................. 6-7

Hoses and Fittings ........................................................ 8

Hose Connections ......................................................... 8

Operation ....................................................................... 9

Maintenance ................................................................ 10

Troubleshooting ........................................................... 11

Español ........................................................................ 13

Français ....................................................................... 25

Deutsch ....................................................................... 37

Italiano ......................................................................... 49

Illustrations and Parts Lists .................................... 60-64

Description

Greenlee Utility Remote Control Valves are compact,

lightweight, high-pressure valves rated for a maximum

of 700 bar (10,000 psi) of hydraulic pressure. They

are intended to provide control for hydraulic tools that

operate on Open-Center hydraulic systems.

The PVA0021 is for single-acting tools and features a

3/8" coupler. The PVA0022 is for double-acting tools

and has 1/4" couplers.

These four-way valves have three operating positions:

Advance, Neutral, and Retract. A special hold feature

locks the tool in its stroke when the lever is in the

neutral position.

To reduce operator fatigue, they feature an automatic

spring-returned lever. This provides automatic shut-off

and returns the valve to neutral when the hydraulic sys-

tem’s operating pressure is achieved, or when the tool is

at the end of its stroke.

For operator safety, Greenlee Utility remote control

valves include a ground dump relief valve in the valve

return circuit. This relief valve will automatically open

if the return couplers are not connected properly. The

ground dump relief pressure for each model is listed in

under Specications.

In addition, the PVA0022 has an internal relief valve

that limits the tool retract pressure. This feature pro-

tects tools that cannot withstand a return-side pressure

greater than:

• 345 bar (5000 psi)

PVA0021 • PVA0022

Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

3

IMPORTANT SAFETY INFORMATION

SAFETY

ALERT

SYMBOL

This symbol is used to call your attention to hazards

or unsafe practices which could result in an injury or

property damage. The signal word, dened below,

indicates the severity of the hazard. The message

after the signal word provides information for pre-

venting or avoiding the hazard.

Immediate hazards which, if not avoided, WILL result

in severe injury or death.

Hazards which, if not avoided, COULD result in

severe injury or death.

Hazards or unsafe practices which, if not avoided,

MAY result in injury or property damage.

Read and understand all of the

instructions and safety information

in this manual before operating or

servicing this tool.

Failure to observe this warning

could result in severe injury or death.

Electric shock hazard:

This tool is not insulated. When

using this unit near energized

electrical lines, use only certied

non-conductive hoses and proper

personal protective equipment.

Failure to observe this warning

could result in severe injury or death.

Skin injection hazard:

• Do not use hands to check for

leaks.

• Do not hold hose or couplers

while

the hydraulic system is

pressurized.

• Depressurize the hydraulic system

before servicing.

Oil under pressure easily punctures

skin causing serious injury, gan-

grene or death. If you are injured by

escaping oil, seek medical attention

immediately.

Wear eye protection when operating

or servicing this tool.

Failure to wear eye protection could

result in serious eye injury from

ying debris or hydraulic oil.

PVA0021 • PVA0022

Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

4

Use hoses, ttings, and other components rated

for 700 bar (10,000 psi). An under-rated component

may fail under pressure.

Failure to observe this warning could result in severe

injury or death.

Valve and other components may be

hot during and after operation. Allow

to cool before handling, or handle

with heat-resistant gloves.

Failure to observe this warning

could result in severe injury.

Wear gloves when using this tool.

Failure to observe this warning

could result in serious injury.

Do not exceed the maximum hydraulic ow, pres-

sure relief or back pressure listed in the specica-

tions section of this manual.

Failure to observe this warning could result in severe

injury or death.

Do not disconnect valve, hoses or ttings while the

power source is running or if the hydraulic uid is

hot. Hot hydraulic uid can cause serious burns.

Do not reverse hydraulic ow. Operation with

hydraulic ow reversed can cause tool malfunction.

Connect the pressure (supply) hose and tank (return)

hose to the proper ports.

Do not change accessories, inspect, adjust or

clean valve when it is connected to a power source.

Accidental start-up can result in serious injury.

Failure to observe this warning could result in severe

injury or death.

IMPORTANT SAFETY INFORMATION

PVA0021 • PVA0022

Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

5

IMPORTANT SAFETY INFORMATION

Hydraulic oil can cause skin irritation.

• Handle the valve and hoses with care to prevent

skin contact with hydraulic oil.

• In case of accidental skin contact with hydraulic

oil, wash the affected area immediately to remove

the oil.

Failure to observe these precautions may result in

injury.

• Inspect the hydraulic hoses and couplings every

operating day. Repair or replace if leakage, crack-

ing, wear or damage is evident. Damaged hoses

or couplings can fail, resulting in injury or property

damage.

• Make sure all bystanders are away from the work

area when handling, starting, and operating the

tool. Nearby personnel can be injured by ying

debris or by ying parts in the event of a tool

malfunction.

Use the valve for manufacturer’s intended purpose

only. Use other than that which is instructed in this

manual can result in injury or property damage.

Do not use this valve to operate a hydraulic jack.

The valve is not intended for this use.

Emergency stop procedure:

1. Release the lever.

2. Shut off the hydraulic power source.

Procedure for connecting or disconnecting hydraulic

hoses, ttings or components:

1. Set the PVA valve to the neutral position.

2. Move the ow lever on the power source to the

OFF position.

3. Stop the hydraulic power source.

4. Follow the sequence under Hose Connections

to prevent pressure buildup. In case some

pressure has built up, loosen hoses, ttings or

components slowly.

Note: Keep all decals clean and legible, and replace

when necessary.

PVA0021 • PVA0022

Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

6

Identiﬁcation

1. Tank Port

2. Pressure Port

3. Pressure Coupler

4. Return Coupler

5. Plug

6. Lever

1

2

3

4

6

1

2

3

5

6

PVA0021

PVA0022

SUPPLY

SIDE

TOOL

SIDE

Speciﬁcations

PVA0021

Type of Valve .................................................Single-Acting

Type of Hydraulic System .............................Open-Center

Tool Connection .................3/8–18 Female Quick Coupler

Power Source Connection

Pressure ...................................................... 1/4–18 NPT

Tank ............................................................ 1/4–18 NPT

Ground Dump

Relief Valve Setting ......... 207–276 bar (3000–4000 psi)

Return Relief Valve Setting .......................................... N/A

Pressure Relief Valve Setting ............. 700 bar (10,000 psi)

Length ..........................................................231 mm (9.1")

Width ............................................................45 mm (1.75")

Height ...........................................................83 mm (3.25")

Weight/Mass .............................................. 1.3 kg (2.75 lb)

PVA0022

Type of Valve ...............................................Double-Acting

Type of Hydraulic System .............................Open-Center

Tool Connection

Pressure ........................1/4–18 NPSM Female Coupler

Return ...............................1/4–18 NPSM Male Coupler

Power Source Connection

Pressure ...................................................... 1/4–18 NPT

Tank ............................................................ 1/4–18 NPT

Ground Dump

Relief Valve Setting ........ 207–276 bar (3000–4000 psi)

Return Relief Valve Setting ................... 345 bar (5000 psi)

Pressure Relief Valve Setting ............. 700 bar (10,000 psi)

Length ..........................................................191 mm (7.5")

Width ............................................................45 mm (1.75")

Height ...........................................................83 mm (3.25")

Weight/Mass ................................................ 1.2 kg (2.5 lb)

PVA0021 • PVA0022

Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

7

Speciﬁcations (cont’d)

Hydraulic Power Source

Do not exceed the following hydraulic power source

maximums:

• Hydraulic ow: See the product specications

• Pressure relief: 138 bar (2000 psi)

• Back pressure: 13.8 bar (200 psi)

Failure to observe this warning could result in severe

injury or death.

Type of Hydraulic System .............................Open-Center

Filtration ............................................. 10 Micron (nominal)

Pressure Relief Setting .......................... 138 bar (2000 psi)

Back Pressure (Maximum)* .................... 13.8 bar (200 psi)

* 13.8 bar (200 psi) is the maximum agreed standard back pressure

for the HTMA (Hydraulic Tool Manufacturers Association).

Greenlee Utility tools will operate satisfactorily at this standard.

1. Maximum hydraulic uid temperature must not

exceed 60 °C (140 °F). A sufcient oil cooling

capacity is needed to limit the hydraulic uid

temperature.

2. Hydraulic ow must not exceed 5 l/min (1.32 gpm).

Install a ow meter in the return line to measure to

rate of hydraulic ow before using the tool.

3. Pressure relief valve setting must not exceed

138bar (2000 psi) at your tool’s maximum ow.

Locate the pressure relief valve in the supply circuit

to limit excessive hydraulic pressure to the tool.

Recommended Hydraulic Fluids

Use any non-detergent, petroleum-based hydraulic

uid which meets the following specications or HTMA

specications.

S.U.S. @:

38 °C (100 °F) ...............................................140 to 225

99 °C (210 °F) ............................................ 40 minimum

Flash Point .................................170 °C (340 °F) minimum

Pour Point ...................................-34 °C (-30 °F) minimum

T

P

POWER

SOURCE

2,000 PSI

FLOW

ON/OFF

VALVE

MEDIUM

PRESSURE

HOSES

T

P

INTENSIFIER

4,000-

10,000 PSI

P

T

P

VALVE

T

P

HIGH

PRESSURE

PUMP

4,000-

10,000 PSI

FLOW

ON/OFF

VALVE

SYMBOL FOR

DISCONNECT COUPLER

R

P

T

P

TOOL

REMOTE

COUPLING

HIGH

PRESSURE

HOSES

P

T

P

TOOL

DIRECT

COUPLING

P

SINGLE

ACTING

OUT

IN

HIGH

PRESSURE

HOSES

OUT

IN

DIRECT CONNECT

DOUBLE ACTING

Hydraulic Schematic

PVA0021 • PVA0022

Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

8

Hoses and Fittings

Installation and Maintenance

See publication 99930323, SAE J1273

(Hose and Hose Assemblies)

Replacement

Refer to a Greenlee Utility catalog or bulletin 99910322

for a complete selection of hoses and ttings.

Hose Connections

Connecting Hoses

1. Move the ow lever on the power source to the OFF

position.

2. Stop the hydraulic power source.

3. Connect the hoses in the order shown.

Disconnecting Hoses

1. Move the ow lever on the power source to the OFF

position.

2. Stop the hydraulic power source.

3. Disconnect the hoses in the order shown.

4. Install dust caps.

Note: Return (tank) hose connection should always be

connected before supply (pressure) hose connection to

prevent pressure buildup inside the unit.

4

5

2

1

3

PVA0021

T

P

2

4

1

3

PVA0022

5

6

T

P

Power Source

(138 bar or 2000 psi max.)

Power Source

(138 bar or 2000 psi max.)

Intensiﬁer

(700 bar or 10,000 psi max.)

Intensiﬁer

(700 bar or 10,000 psi max.)

Single-Acting Tool

Double-Acting Tool

PVA0021

Connection Sequence: 1 – 2 – 3 – 4 – 5

Disconnection Sequence: 5 – 4 – 3 – 2 – 1

P = pressure, or supply

T = tank, or return

PVA0022

Connection Sequence: 1 – 2 – 3 – 4 – 5 – 6

Disconnection Sequence: 6 – 5 – 4 – 3 – 2 – 1

P = pressure, or supply

T = tank, or return

PVA0021 • PVA0022

Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

9

Operation

Electric shock hazard:

This tool is not insulated. When

using this unit near energized

electrical lines, use only certied

non-conductive hoses and proper

personal protective equipment.

Failure to observe this warning

could result in severe injury or death.

Skin injection hazard:

• Do not use hands to check for

leaks.

• Do not hold hose or couplers

while

the hydraulic system is

pressurized.

• Depressurize the hydraulic system

before servicing.

Oil under pressure easily punctures

skin causing serious injury, gan-

grene or death. If you are injured by

escaping oil, seek medical attention

immediately.

Wear eye protection when operating

or servicing this tool.

Failure to wear eye protection could

result in serious eye injury from

ying debris or hydraulic oil.

Use hoses, ttings, and other components rated

for 700 bar (10,000 psi). An under-rated component

may fail under pressure.

Failure to observe this warning could result in severe

injury or death.

Valve and other components may be

hot during and after operation. Allow

to cool before handling, or handle

with heat-resistant gloves.

Failure to observe this warning

could result in severe injury.

Note: Maintain proper footing and balance while using

the tool. Do not over-reach. Unsuitable footing and

balance may not allow counteracting normal or unex-

pected movement of the tool.

1. Start the power source.

Note: Allow the power source to run for a few

minutes to warm the hydraulic ﬂuid.

2. Position the tool in the appropriate location or

position.

3. To start the tool, press the lever to ADVANCE.

Notes:

• When the hydraulic pressure reaches 207 bar to

276 bar (3000 psi to 4000 psi), you may release

the lever and it will stay in the ADVANCE position.

The tool will continue to advance until the intensi-

ﬁer reaches 700 bar (10,000 psi).

• You may stop the tool at any time by pressing the

lever to NEUTRAL.

4. To retract the tool, press the lever to RETRACT.

5. When the tool is not in use, stop the power source

to reduce heat and wear on tool components.

PVA0021 • PVA0022

Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

10

Maintenance

Wear eye protection when operating

or servicing this tool.

Failure to wear eye protection could

result in serious eye injury from

ying debris or hydraulic oil.

Do not change accessories, inspect, adjust or

clean valve when it is connected to a power source.

Accidental start-up can result in serious injury.

Failure to observe this warning could result in severe

injury or death.

Use this maintenance schedule to maximize the tool’s

service life.

Notes: Keep decals clean and legible. Replace when

necessary — see the decals in the Parts List.

When disposing of any components (hydraulic hoses,

hydraulic ﬂuid, worn parts, etc.), do so in accordance

with federal, state and local laws or ordinances.

Daily

1. Wipe all tool surfaces clean.

2. Inspect the hydraulic hoses and ttings for signs

of leaks, cracks, wear or damage. Replace if

necessary.

3. Install dust caps when the tool is disconnected.

Monthly

1. Perform a thorough inspection of the hydrau-

lic hoses and ttings as instructed in publication

99930323, SAE J1273 (Hose and Hose Assemblies).

2. Check the pressure to the tool by installing an in-line

pressure gauge, rated for 700 bar (10,000psi),

between the valve and the tool.

Annually

If required by your organization, have the tool inspected

by an authorized Greenlee Utility service center.

PVA0021 • PVA0022

Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

11

Problem Probable Cause Probable Remedy

Tool does not operate. Improper power source. Verify that the power source meets

the specications. Refer to the

Specications section.

Hydraulic uid level low. Check the uid level. Check system for

leaks.

Incorrect hydraulic uid viscosity. Use hydraulic uid with the correct

viscosity. Refer to the Specications

section.

Tool operates slowly or

erratically.

Hydraulic uid cold. Allow uid to warm to the operating

temperature. Actuate the tool intermit-

tently to reduce the warming time.

Power source not adjusted correctly. Refer to the power source operator’s

manual. Set the ow and pressure to

correspond with the tool.

Hydraulic uid level low. Check the uid level. Check system for

leaks.

Air in the hydraulic system. Refer to the power source manufac-

turer’s instructions for removing air from

the system.

Incorrect hydraulic uid viscosity. Use hydraulic uid with the correct

viscosity. Refer to the Specications

section.

Tool feels hot. Hydraulic uid level low. Check the uid level. Check for leaks.

Incorrect hydraulic uid viscosity. Use hydraulic uid with the correct

viscosity. Refer to the Specications

section.

Hydraulic uid dirty. Refer to the power source owner’s

manual for procedure to replace

hydraulic oil and lter.

Troubleshooting

Before troubleshooting, determine whether the problem

is in the tool, the hoses, or the power source. Substitute

a tool, hoses, or power source known to be in good

working order to eliminate the item that is not operating.

If the problem is in the tool, see the troubleshoot-

ing table in this manual. If the problem is in the power

source, see the troubleshooting section of the power

source instruction manual.

PVA0021 • PVA0022

Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

12

Page is loading ...

PVA0021 • PVA0022

Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

24

Page is loading ...

PVA0021 • PVA0022

Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

36

Page is loading ...

PVA0021 • PVA0022

Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

48

Page is loading ...

PVA0021 • PVA0022

Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

60

Illustration

T

P

SUPPLY

4

5

6

7

8

9

15

13

12

11

15

13

12

11

17

33

34

21

24

18

19

1

3

2

26

35

36

37

25

28

42

PVA0021

38

43

41

PVA0022

38

39

42

BEFORE

MODEL CODE:

FMN00246

FMP00190

FMR00085

FNK00043

22

21

23

PVA0022

AFTER

MODEL CODE:

FMN00246

FMP00190

FMR00085

FNK00043

22

45

23

PVA0022

20

21

PAV0021

45

20

PAV0021

PVA0021 • PVA0022

Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

61

Parts List

UPC No. Qty Qty

Key 78-3310- Part No. Description PVA0021 PVA0022

1 43459 50434594 Valve Lever with Warning Decal (next item) ............. 1 ...................1

43460 50434608 Decal, Warning (not shown) ..................................... 1 ...................1

2 43461 50434616 Decal, Identication ................................................. 1 ...................0

2 43462 50434624 Decal, Identication ................................................. 0 ...................1

3A 43464 50434640 Screw, #6–32 x .187 Truss Head ............................. 2 ...................2

3B 48703 50487035 Screw, #8–32 x .250 Slotted Truss Head................. 2 ...................2

4 43465 50434659 Valve, Cap ................................................................ 1 ...................1

5* O-ring, 1.75 x 1.875 x .062–70 ................................ 1 ...................1

6 42017 50420173 Race, Thrust, 1.002 x 1.552 x .032.......................... 1 ...................1

7 43467 50434675 Bearing, Thrust, 1.005 x 1.547 x .078 .....................1 ...................1

8 43468 50434683 Disk Unit, Valve ........................................................ 1 ...................1

9 43469 50434691 O-ring, .250 x .375 x .062–70 .................................. 2 ...................2

11 43470 50434705 Seal, Shear .............................................................. 3 ...................3

12* Backup Ring, Single Turn, .140 x .246 x .048 ......... 3 ...................3

13* O-ring, .125 x .250 x .062–70 .................................. 3 ...................3

15*A Spring, Compression, .145 x .215 x .455 ................ 3 ...................3

15*B Spring, Compression ............................................... 3 ...................3

17 Screw, #10–32 x 1.75 Socket Head ........................ 2 ...................2

18 43473 50434730 Stop, Treadle ........................................................... 2 ...................2

19 43474 50434748 Spring, Compression ............................................... 2 ...................2

20 43475 50434756 Port Plug .................................................................. 1 ...................0

21 Screw, Set, 3/8–24 x .187, Hollow Socket ..............2 ...................2

22 30146 50301462 Pin, Valve, .305 x .870 ............................................. 0 ...................1

23 48234 50482343 Spring, Compression, .190 x .318 x 1.088 .............. 0 ...................1

24 43477 50434772 Block, PVA Valve ..................................................... 1 ...................1

25 41830 50418301 Dust Cap (not shown) .............................................. 1 ...................0

26 43478 50434780 Boot, Rubber ........................................................... 1 ...................1

28 40764 50407641 Plug, 1/4–18 NPSM ................................................. 1 ...................0

33 30146 50301462 Pin, Valve, .305 x .870 ............................................. 1 ...................1

34 48234 50482343 Spring, Compression, .190 x .318 x 1.088 .............. 1 ...................1

35 40748 50407481 Adapter, 3/8–18 NPTF to 1/4–18 NPSM F/M .......... 1 ...................0

36 41877 50418771 Female Coupler ....................................................... 1 ...................0

37* O-ring, .750 x 1.00 x .125–90 .................................. 1 ...................0

38 41834 50418341 Dust Cap (not shown) .............................................. 0 ...................2

39 40647 50406471 Male Coupler, 1/4–18 NPSM ................................... 0 ...................1

41 40652 50406522 Female Coupler, 1/4–18 NPSM ............................... 0 ...................1

42 40646 50406461 Washer, Flat, .514 x .030, Copper .......................... 2 ...................2

43* O-ring .....................................................................0 ...................1

45 54643 90546431 Screw, Set, 7/16–20 Hollow Socket ........................ 2 ...................2

* 43479 50434799 Packing Kit (includes all items marked with an asterisk)

Legend:

A Units prior to the following serial numbers:

FMN00700, FMP00600, FMR00500, FNK00400

B Units after the following serial numbers:

FMN00700, FMP00600, FMR00500, FNK00400

PVA0021 • PVA0022

Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

62

6 FT 6 FT 10 FT 10 FT

Key UPC No. Part No. UPC No. Part No. Description Qty

41107 50411074 41108 50411083 10,000 psi Certied Non-Conductive Hose .................................................................. 1

1 41795 50417951 41796 50417961 Hose assembly, 1/4" high-pressure, 1/4 MNPT both ends .......................................2

2 41401 50414014 41401 50414014 Coupling, 1/4 FNPT x 1/4 FNPT ................................................................................2

3 41344 50413442 41344 50413442 Adapter, 1/4 MNPT x 1/4 MNPT ................................................................................ 1

4 54169 51541690 54169 51541690 Male coupler, 1/4 FNPT .............................................................................................1

5 42096 50420961 42096 50420961 Female coupler, 1/4 MNPT ........................................................................................1

41842 50418421 41842 50418421 O-ring, 5/8 x 13/16 x 3/32–90 ................................................................................1

6 41834 50418341 41834 50418341 Dust cap ....................................................................................................................2

7 Ty-Rap .......................................................................................................................3

Accessories

700 bar (10,000 psi) High-Pressure Certiﬁed Non-conductive Hose

5

2 3 4 6

7

1

PVA0021 • PVA0022

Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

63

Accessories (cont’d)

700 bar (10,000 psi) High-Pressure Couplers

UPC No.

Key 78-3310- Part No. Description Qty

1 54169 51541690 Male coupler, 1/4 FNPT ..........................1

41941 50419411 Male coupler, 3/8 FNPT ..........................1

2 40647 50406471 Male coupler, 1/4 MNPS .........................1

40646 50406461 Washer, copper ...................................1

3 42096 50420961 Female coupler, 1/4 MNPT .....................1

41842 50418421 O-ring, 5/8 x 13/16 x 3/32–90 .............1

40652 50406522 Female coupler, 1/4 MNPS .....................1

41842 50418421 O-ring, 5/8 x 13/16 x 3/32–90 .............1

40646 50406461 Washer, copper ...................................1

41877 50418771 Female coupler, 3/8 MNPT ....................1

42030 50420304 O-ring, .734 x 1.012 x .139–90 ...........1

1 2 3

PVA0021 • PVA0022

Accessories (cont’d)

Flow Test Kit for Testing Low-Pressure Systems

UPC No.

Key 78-3310- Part No. Description Qty

40884 50408840 Flow test kit (includes items 1–5) ............................ 1

1 Flow meter and gauge, 1–10 gpm, 0–3,000 psi,

1/2 FNPT both ends (Hedland #693015) ................. 1

2 41351 50413513 Adapter, 1/2 MNPT x 1/2 MNPT .............................. 2

3 41778 50417781 Female coupler, 1/2 FNPT ....................................... 1

4 41779 50417791 Male coupler, 1/2 FNPT ........................................... 1

5 41834 50418341 Dust cap .................................................................. 2

5

3

2

1

2

4

5

USA 800-435-0786 Fax: 800-451-2632

815-397-7070 Fax: 815-397-1865

Canada 800-435-0786 Fax: 800-524-2853

International +1-815-397-7070 Fax: +1-815-397-9247

4455 Boeing Drive • Rockford, IL 61109-2988 • USA • 815-397-7070

An ISO 9001 Company • Greenlee Textron Inc. is a subsidiary of Textron Inc.

www.greenlee.com

Greenlee PVA0021, PVA0022 Hydraulic Control Valves User manual

Greenlee PVA0021, PVA0022 Hydraulic Control Valves User manual

in other languages

Related papers

Other documents