CMA Dishmachines CMA-180-VL Quick Installation Guide

CMA Dishmachines
Brand
CMA Dishmachines
Model
CMA-180-VL
Category
Dishwashers
Type
Quick Installation Guide

This manual is also suitable for

2
STEP
1
STEP
WALL
DRAIN
8"
FLOOR DRAIN
Connect a 2" drain pipe (not supplied) from scrap
accumulator to floor or wall drain.
Connect dishmachine to hot water source 120°F -
140°F. Connect cold water inlet (min 41°F and max
65°F). (Review other side for details).
Remove the plug from the mixing chamber and install
the rinse injection fitting (rinse injection fitting
provided by your dispenser supplier; CMA does not
supply).
Remove the plastic plug to install the detergent
fitting (provided by your dispenser supplier;
CMA does not supply).
3 Phase: Connect power supply wires, L1, L2 and L3
to the appropriate terminals marked L1, L2 and L3 on
the power block. Important: If one of the three wires
has higher voltage it must be inserted as L-2.
3
STEP
L2
L3
L1
208/240
3 PHASE OR SINGLE
PHASE
L1 AND L3
FOR SINGLE PHASE
10-2017
CMA-180-VL
REAR VIEW
4
STEP
PLASTIC
PLUG
WARNING: Electrical and plumbing
connections need to be made by a
licensed service person and comply
with all Federal, State and Local
Health, Electrical, Plumbing and
Safety codes.
DRAIN
CONNECTION
1
DETERGENT
FITTING INLET
4
HOT WATER
INLET
2
MIXING
CHAMBER
5
POWER
BLOCK
3
Push "RINSE TOGGLE SWITCH”, located on the back
of the control box, to fill the booster tank.
6
STEP
CMA-180-VL 3 Doors/Tall
Quick Setup Instructions
RINSE TOGGLE
SWITCH
LOCATED ON
BACK SIDE OF
CONTROL PANEL
6
5
STEP
HOT
WATER INLET
COLD
WATER INLET
COLD WATER INLET
LOCATED ON FRONT
OF MACHINE
2
PN: 10130.17
CMA-180-VL
VENTLESS
VENTLESS
Press "POWER ON/OFF" rocker switch to turn on
dishmachine.
Press "AUTO FILL" immediately after power is
turned on. Timer will automatically fill until the water
overflows into the scrap trap. The initial fill may need
to be pushed twice to fill wash tank.
Adjust the temperature by removing the panel in front
of the respective heater and turning the adjustment
post. Wash temp. 155°F. Rinse temp.180°F.
STEP
11
Open dishmachine doors completely. Closing the
doors will automatically activate the machine.
STEP
10
Remove the stainless steel plug to install the detergent
probe (provided by your dispenser supplier; CMA
does not supply).
12
STEP
10-2017
WARNING: Electrical and plumbing connections
need to be made by a licensed service person
and comply with all Federal, State and Local
Health, Electrical, Plumbing and Safety codes.
7
STEP
20
Adjust pressure regulator located next to cold water inlet, to
20 psi (maximum).
RINSE
PRESSURE
PRESSURE
RELIEF VALVE
8
STEP
9
STEP
CMA-180-VL 3 Doors/Tall
Quick Setup
Instructions
CMA-180-VL
FRONT VIEW
AUTO FILL
9
CYCLE LIGHT
MIXING
CHAMBER
POWER
ON OFF
8
DOOR
HANDLE
10
HEATER
THERMOSTAT
11
GAUGES
7
BOOSTER
HEATER
DETERGENT
PROBE INLET
12
WASH TANK
HEATER
COLD WATER
INLET
2
BLACK/YELLOW
STRIPED WIRE
BOOSTER HEATER
DAMAGE PREVENTION
CAUTION: TO PREVENT BOOSTER
HEATER ELEMENT DAMAGE, CMA
HAS DISCONNECTED A WIRE FROM
THE “HIGH-LIMIT SWITCH”.
THE BOOSTER TANK MUST BE
FILLED WITH WATER PRIOR TO
CONNECTING THE “REMOVED”
WIRE, AT THE INITIAL FILLING OF
A NEWLY INSTALLED DISHMACHINE.
TO FILL THE BOOSTER TANK, LOCATE
THE “RINSE TOGGLE SWITCH” ON
BACK OF CONTROL BOX. PUSH THE
TOGGLE SWITCH TO ACTIVATE THE
WATER SOLENOID THAT FILLS THE
BOOSTER TANK. THE BOOSTER TANK
INDICATES FULL, WHEN YOU CAN
OBSERVE WATER SPRAYING FROM
THE RINSE ARMS. AT THIS POINT,
AND ONLY AT THIS POINT, SHOULD
YOU CONNECT THE “DISCONNECTED”
WIRE. FAILING TO FOLLOW THESE
IMPORTANT INSTRUCTIONS WILL
DESTROY THE HEATING ELEMENT,
BECAUSE THE ELEMENT SHOULD
ONLY OPERATE WHEN FULLY
SUBMERGED IN WATER.
NOTE: The wash-down feature for HR
Condenser is automatically activated when
the machine’s “Master Power Switch” is
turned “off”. Approximately (2) gallons of
hot water will spray over the HR Condenser,
cleansing and discharging into drain system.
The Spirit of Excellence
an Ali Group Company
PN: 10130.17
DOOR SAFETY
INTERLOCK
  • Page 1 1
  • Page 2 2

CMA Dishmachines CMA-180-VL Quick Installation Guide

CMA Dishmachines
Brand
CMA Dishmachines
Model
CMA-180-VL
Category
Dishwashers
Type
Quick Installation Guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents