HP (Hewlett-Packard) Laptop 2500 User manual

Brand: HP (Hewlett-Packard)

Model: Laptop 2500

Category: Network switches

Type: User manual

This manual is also suitable for

2500

hp procurve

series 2300 and 2500 switches

installation and

getting started guide

www.hp.com/go/procurve

HP ProCurve

Series 2300 and 2500 Switches

Installation and Getting Started Guide

2353-ed2.book Page i Friday, February 9, 2001 6:00 PM

Hewlett-Packard Company

8000 Foothills Boulevard, m/s 5552

Roseville, California 95747-5552

http://www.hp.com/go/hpprocurve

This document contains information which is protected by

prior permission is prohibited, except as allowed under the

Publication Number

5969-2353

Edition 2

March 2001

Applicable Products

Series 2300:

· HP ProCurve Switch 2312 (J4817A)

· HP ProCurve Switch 2324 (J4818A)

Series 2500:

· HP ProCurve Switch 2512 (J4812A)

· HP ProCurve Switch 2524 (J4813A)

Disclaimer

The information contained in this document is subject to

change without notice.

HEWLETT-PACKARD COMPANY MAKES NO WARRANTY

OF ANY KIND WITH REGARD TO THIS MATERIAL,

INCLUDING, BUT NOT LIMITED TO, THE IMPLIED

WARRANTIES OF MERCHANTABILITY AND FITNESS

FOR A PARTICULAR PURPOSE. Hewlett-Packard shall not

be liable for errors contained herein or for incidental or

consequential damages in connection with the furnishing,

performance, or use of this material.

Hewlett-Packard assumes no responsibility for the use or

reliability of its software on equipment that is not furnished

by Hewlett-Packard.

Warranty

See the Customer Support/Warranty booklet included with

the product.

A copy of the specific warranty terms applicable to your

Hewlett-Packard products and replacement parts can be

obtained from your HP Sales and Service Office or

authorized dealer.

Safety

Before installing and operating these products, please read

the “Installation Precautions” in chapter 2, “Installing the

Switch 2300 and 2500”, and the safety statements in appendix

C, “Safety and Regulatory Statements”.

2353-ed2.book Page ii Friday, February 9, 2001 6:00 PM

iii

Contents

1 Introducing the HP ProCurve Series

2300 and 2500 Switches

Front of the Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Network Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

Mode LED Select Button and Indicator LEDs . . . . . . . . . . . . . . . . . . . . 1-5

Console Port (Series 2500 Switches only) . . . . . . . . . . . . . . . . . . . . . . . 1-6

Download Port (Series 2300 Switches only) . . . . . . . . . . . . . . . . . . . . . 1-6

Reset Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

Clear Button (Series 2500 only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7

Back of the Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7

Power Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7

Switch Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8

Switch Operation Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9

Address Table Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9

Effect of VLANs (Series 2500 only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10

2 Installing the Series 2300 and 2500 Switches

Included Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Installation Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

Installation Precautions: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

1. Prepare the Installation Site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

2. Install Transceivers (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6

3. Verify the Switch Passes Self Test . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7

LED Behavior: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8

4. Mount the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9

Rack or Cabinet Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9

Horizontal Surface Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12

Wall Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12

2353-ed2.book Page iii Friday, February 9, 2001 6:00 PM

5. Connect the Switch to a Power Source . . . . . . . . . . . . . . . . . . . . . . 2-13

6. Connect the Network Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-14

Using the RJ-45 Connectors (10/100Base-TX ports) . . . . . . . . . . 2-14

Connecting Cables to the Transceivers . . . . . . . . . . . . . . . . . . . . . 2-14

7. (Optional) Connect a Console to the Switch 2500 . . . . . . . . . . . . . 2-15

Terminal Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-15

Connecting a Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16

Getting Started With Switch Configuration

(Series 2500 Switches Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-17

Recommended Minimal Configuration . . . . . . . . . . . . . . . . . . . . . . . . . 2-17

Using the Console Setup Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18

Where to Go From Here . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-20

Using the IP Address for Remote Switch Management

(Series 2500 Switches Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-20

Starting a Telnet Session . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-20

Starting a Web Browser Session . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-21

Sample Network Topologies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-22

As a Desktop Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-22

As a Segment Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-23

Connecting to a Backbone Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-24

Stacking the Switches (Series 2500 only) . . . . . . . . . . . . . . . . . . . . . . 2-25

3 Troubleshooting

Basic Troubleshooting Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

Diagnosing with the LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4

Proactive Networking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8

Hardware Diagnostic Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9

Testing the Switch by Resetting It . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9

Checking the Switch LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9

Checking Console Messages (Series 2500 switches only) . . . . . . 3-9

Testing Twisted-Pair Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10

Testing Switch-to-Device Network Communications . . . . . . . . . . . . 3-10

Testing End-to-End Network Communications . . . . . . . . . . . . . . . . . 3-10

Restoring the Factory Default Configuration

(Series 2500 switches only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11

2353-ed2.book Page iv Friday, February 9, 2001 6:00 PM

Downloading New Code

(Series 2300 switches only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12

To Perform the Download: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12

HP Customer Support Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13

Before Calling Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13

A Specifications

Physical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1

Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1

Environmental . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1

Acoustic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2

Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2

Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2

B Switch Ports and Network Cables

Switch Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1

Twisted Pair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1

Fiber-Optic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1

Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-2

Twisted-Pair Cable/Connector Pin-Outs . . . . . . . . . . . . . . . . . . . . . . . B-3

Straight-Through Twisted-Pair Cable for

10 Mbps or 100 Mbps Network Connections . . . . . . . . . . . . . . . . . . . . B-5

Cable Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-5

Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-5

Crossover Twisted-Pair Cable for

10 Mbps or 100 Mbps Network Connection . . . . . . . . . . . . . . . . . . . . . B-6

Cable Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-6

Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-6

Straight-Through Twisted-Pair Cable for

1000 Mbps Network Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-7

Cable Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-7

Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-7

C Safety and EMC Regulatory Statements

Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-1

EMC Regulatory Statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-8

2353-ed2.book Page v Friday, February 9, 2001 6:00 PM

2353-ed2.book Page vi Friday, February 9, 2001 6:00 PM

1-1

Introducing the HP ProCurve

Series 2300 and 2500

Introducing the HP ProCurve Series

2300 and 2500 Switches

The HP ProCurve Series 2300 and 2500 Switches are multiport high-speed

switches that can be used to build high-performance switched workgroup

networks. These switches are store-and-forward devices that offer low latency

for high-speed networking. With these switches you can directly connect

computers, printers, and servers to provide dedicated bandwidth to those

devices, and you can build a switched network infrastructure by connecting

these switches to hubs, other switches, or routers. In addition, the Series 2500

Switches offer full network management capabilities.

This chapter describes your HP Series 2300 and 2500 Switches including:

■ Front and back of the switches

■ Features

■ Switch operation overview

Throughout this manual, these switches will be abbreviated as the “Series 2300

Switches” and “Series 2500 Switches”, or when common features are being

described, as the “Series 2300 and 2500 Switches”.

234 5 6

789101112

Transceiver Ports

10/100Base-T Ports (1-12)

(all ports are HP Auto-MDIX)

LED Mode Select

Mode

Link

Mode

Link

Reset

23456

10 11 12

Act FDx

Max

Fan

Status

Self

Test

Download Port

hp procurve

switch 2312

J4817A

Power

Fault

( See manual for supported transceivers)

234 5 6 131415161718

7 8 9 101112 192021222324

Transceiver Ports

10/100Base-T Ports (1-24)

(all ports are HP Auto-MDIX)

LED Mode Select

Mode

Link

Mode

Link

Reset

23456

14 15 16 17 18

10 11 12

20 21 22 23

Act FDx

Max

Fan

Status

Self

Test

Download Port

hp procurve

switch 2324

J4818A

Power

Fault

( See manual for supported transceivers)

HP ProCurve Switch 2312

(J4817A)

HP ProCurve Switch 2324

(J4818A)

234 5 6

789101112

Transceiver Ports

10/100Base-T Ports (1-12)

(all ports are HP Auto-MDIX)

LED Mode Select

Mode

Link

Mode

Link

Reset

23456

10 11 12

Act FDx

Max

Fan

Status

Self

Test

Console

hp procurve

switch 2512

J4812A

Clear

Power

Fault

( See manual for supported transceivers)

234 5 6 131415161718

789101112 192021222324

Transceiver Ports

10/100Base-T Ports (1-24)

(all ports are HP Auto-MDIX)

LED Mode Select

Mode

Link

Mode

Link

Reset

23456

14 15 16 17 18

10 11 12

20 21 22 23

Act FDx

Max

Fan

Status

Self

Test

Console

hp procurve

switch 2524

J4813A

Clear

Power

Fault

( See manual for supported transceivers)

HP ProCurve Switch 2512

(J4812A)

HP ProCurve Switch 2524

(J4813A)

Series 2300 Switches

Series 2500 Switches

2353-ed2.book Page 1 Friday, February 9, 2001 6:00 PM

1-2

Introducing the HP ProCurve Series 2300 and 2500 Switches

Front of the Switches

Introducing the HP ProCurve

Series 2300 and 2500

Front of the Switches

Network Ports

■ 12 or 24 autosensing 10/100Base-TX ports.

All these ports have the “HP Auto MDIX” feature, which means that you

can use either straight-through or crossover twisted-pair cables to

connect any network devices to the switch.

■ Two transceiver slots for installing any of the supported gigabit and 100

Mbps transceivers.

2345 6 131415161718

7 8 9 101112 192021222324

Transceiver Ports

10/100Base-T Ports (1-24)

(all ports are HP Auto-MDIX)

LED Mode Select

Mode

Link

Mode

Link

Reset

23456

14 15 16 17 18

10 11 12

20 21 22 23

Act FDx

Max

Fan

Status

Self

Test

Console

hp procurve

switch 2524

J4813A

Clear

Power

Fault

( See manual for supported transceivers)

2345 6 131415161718

7 8 9 101112 192021222324

Transceiver Ports

10/100Base-T Ports (1-24)

(all ports are HP Auto-MDIX)

LED Mode Select

Mode

Link

Mode

Link

Reset

23456

14 15 16 17 18

10 11 12

20 21 22 23

Act FDx

Max

Fan

Status

Self

Test

Download Port

hp procurve

switch 2324

J4818A

Power

Fault

( See manual for supported transceivers)

Reset and Clear

buttons

Download

port

Mode Select button

and indicator LEDs

Link and Mode LEDs

for switch ports

10/100Base-TX RJ-45 ports*

Self Test and Fan

Status LEDs

Power

and Fault

LEDs

HP ProCurve Switch 2524

HP ProCurve Switch 2324

Slots for

Gigabit or 100 Mbps

transceivers

Console

Port

10/100Base-TX RJ-45 ports*

* All 10/100Base-TX RJ-45 ports have the HP Auto MDIX feature.

2353-ed2.book Page 2 Friday, February 9, 2001 6:00 PM

1-3

Introducing the HP ProCurve Series 2300 and 2500 Switches

Front of the Switches

Introducing the HP ProCurve

Series 2300 and 2500

LEDs

Table 1-1. Switch LEDs

Switch LEDs State Meaning

Power

(green)

On The switch is receiving power.

Off The switch is NOT receiving power.

Fault

(orange)

Off The normal state; indicates that there are no fault conditions on the switch.

Blinking

†

A fault has occurred on the switch, one of the switch ports, or the fan. The Status LED

for the component with the fault will blink simultaneously.

On On briefly after the switch is powered on or reset, at the beginning of switch self test.

If this LED is on for a prolonged time, the switch has encountered a fatal hardware

failure, or has failed its self test. See chapter 3, “Troubleshooting” for more information.

Self Test

(green)

Off The normal operational state; the switch is not undergoing self test.

On The switch self test and initialization are in progress after you have power cycled or

reset the switch. The switch is not operational until this LED goes off. The Self Test LED

also comes on briefly when you “hot swap” a transceiver into the switch; the

transceiver is self tested when it is hot swapped.

Blinking

†

A component of the switch has failed its self test. The status LED for that component,

for example an RJ-45 port, and the switch Fault LED will blink simultaneously.

Mode Select

(3 green LEDs)

Act Indicates that the port Mode LEDs are displaying network activity information.

FDx Indicates that the port Mode LEDs are lit for ports that are in Full Duplex Mode.

Max Indicates that the port Mode LEDs are lit for ports that are operating at their maximum

possible link speed. For the 10/100TX ports, that is 100 Mbps; for any transceivers with

Gigabit capabilities, that is 1000 Mbps.

! Indicates that the port Mode LEDs are displaying network events that could require

operator attention, for example CRC errors or late collisions. See chapter 3,

“Troubleshooting” for more information.

Fan Status

(green)

On The cooling fan is operating normally.

Blinking

†

The cooling fan has failed. The switch Fault LED will be blinking simultaneously.

†

The blinking behavior is an on/off cycle once every 1.6 seconds, approximately.

2353-ed2.book Page 3 Friday, February 9, 2001 6:00 PM

1-4

Introducing the HP ProCurve Series 2300 and 2500 Switches

Front of the Switches

Introducing the HP ProCurve

Series 2300 and 2500

Table 1-2. Switch and Transceiver Port LEDs

Port LEDs State Meaning

Link On Indicates the port is enabled and receiving a link indication from the connected device.

Off One of these conditions exists:

• no active network cable is connected to the port

• the port is not receiving link beat or sufficient light

• the port has been disabled through the switch console, the web browser interface,

or HP TopTools.

Blinking If the LED is blinking simultaneously with the Fault LED, the corresponding port has

failed its self test.

The LED can blink by itself (no Fault LED blinking) for the transceiver ports. This occurs

when a transceiver is installed and the switch has not yet been reset. Transceivers can

be installed in the slots while the switch is powered on, but the switch must be reset

to initialize the transceiver and make it operational.

Mode Displays network activity information, or whether the port is configured for Full Duplex operation, or

maximum link speed operation, or is experiencing network events requiring operator intervention

depending on the mode selected. See “Mode Select Button and Indicator LEDs” below for more

information.

2353-ed2.book Page 4 Friday, February 9, 2001 6:00 PM

1-5

Introducing the HP ProCurve Series 2300 and 2500 Switches

Front of the Switches

Introducing the HP ProCurve

Series 2300 and 2500

Mode LED Select Button and Indicator LEDs

To optimize the amount of information that can be displayed for each of the

switch ports without overwhelming you with LEDs, the Series 2300 and 2500

switches use a Mode LED for each port. The operation of this LED is controlled

by the Mode LED Select button, and the current setting is indicated by the

Mode LED Select indicator LEDs near the button. Press the button to step

from one mode to the next.

■ If the Activity (Act) indicator LED is lit, each Mode LED displays activity

information for the associated port—it flickers as network traffic is

received and transmitted through the port.

■ If the Full Duplex (FDx) indicator LED is lit, the Mode LEDs light for those

ports that are operating in full duplex.

■ If the maximum speed (Max) indicator LED is lit, the Mode LEDs light for

those ports that are operating at their maximum possible link speed: 100

Mbps for 10/100 ports and 100-FX fiber-optic ports, and 1000 Mbps for

100/1000Base-T or gigabit fiber-optic ports.

■ If the attention (!) indicator LED is lit, each Mode LED lights briefly for

each network event that could require operator attention, for example,

late collisions or CRC errors. See chapter 3, “Troubleshooting” for more

information.

Mode LED

(one for each port)

LED Mode Select button

and indicator LEDs

2353-ed2.book Page 5 Friday, February 9, 2001 6:00 PM

1-6

Introducing the HP ProCurve Series 2300 and 2500 Switches

Front of the Switches

Introducing the HP ProCurve

Series 2300 and 2500

Console Port (Series 2500 Switches only)

This port is available on the Series 2500 switches, and is used to connect a

console to the switch by using the serial cable supplied with the switch. This

connection is described under “Connect a Console to the Switch” in chapter

2, “Installing the Switches”. The console can be a PC or workstation running

a VT-100 terminal emulator, or a VT-100 terminal.

Download Port (Series 2300 Switches only)

This port is available on the Series 2300 switches, and is used to connect a PC

to the switch by using any “null modem” cable. This connection is described

under “Connect a Console to the Switch” in chapter 2, “Installing the

Switches”. The PC can then be used to initiate a download of new code to the

Series 2300 switch. New code may be made available if there are any product

enhancements, for example to support new transceivers. (For the Series 2500

switches, you can download new code through the Console port.)

For the procedures to download new code to your Series 2300 switch, please

see “Downloading New Code (Series 2300 Switch)” on page 3-12.

Reset Button

This button is used to reset the switch while it is powered on. This action clears

any temporary error conditions that may have occurred and executes the

switch self test. Press the Reset button also after installing any transceivers

while the switch is powered on. After installing the transceiver, the switch

must be reset to initialize the transceiver and make it operational.

For the Series 2500 switches, this button also resets all network activity

counters to zero. The counters are displayed in the Series 2500 switch console

interface, the web browser interface, and through SNMP network manage-

ment applications, such as HP TopTools for Hubs & Switches.

2353-ed2.book Page 6 Friday, February 9, 2001 6:00 PM

1-7

Introducing the HP ProCurve Series 2300 and 2500 Switches

Back of the Switches

Introducing the HP ProCurve

Series 2300 and 2500

Clear Button (Series 2500 only)

This button is used for these purposes:

■ Deleting Passwords - When pressed by itself for at least one second, the

button deletes any switch console access passwords that you may have

configured. Use this feature if you have misplaced the password and need

console access.

This button is provided for your convenience, but its presence means

that if you are concerned with the security of the switch configuration

and operation, you should make sure the switch is installed in a secure

location, such as a locked wiring closet.

■ Restoring Factory Default Configuration - When pressed with the

Reset button in a specific pattern, any configuration changes you may

have made through the switch console, the web browser interface, and

SNMP management are removed, and the factory default configuration is

restored to the switch. For the specific method to restore the factory

default configuration, see “Restoring the Factory Default Configuration”

in chapter 3, “Troubleshooting” of this manual.

Back of the Switches

Power Connector

The Switch 2300 and Switch 2500 models do not have a power switch; they

are powered on when connected to an active AC power source. The switches

automatically adjust to any voltage between 100-127 and 200-240 volts and

either 50 or 60 Hz. There are no voltage range settings required.

cooling vent - make sure this is not

obstructed for proper switch operation

AC power connector

2353-ed2.book Page 7 Friday, February 9, 2001 6:00 PM

1-8

Introducing the HP ProCurve Series 2300 and 2500 Switches

Switch Features

Introducing the HP ProCurve

Series 2300 and 2500

Switch Features

The features of the Series 2300 and 2500 switches include:

■ 12 or 24 autosensing 10/100Base-TX RJ-45 ports with Auto MDI/MDI-X.

■ two slots for installing supported gigabit or 100Base-FX transceivers.

■ plug-and-play networking—all ports are enabled—just connect the

network cables to active network devices and your switched network is

operational.

■ HP Auto-MDIX on all 10/100 twisted-pair ports, and IEEE 802.3ab Auto

MDI /MDI-X on all 100/1000 twisted-pair ports, meaning that all connec-

tions can be made using straight-through twisted-pair cables.

Cross-over cables are not required, although they will also work. The pin

operation of each port is automatically adjusted for the attached device:

if the switch detects that another switch or hub is connected to the port,

it configures the port as MDI; if the switch detects that an end-node device

is connected to the port, it configures the port as MDI-X.

■ automatic learning of the network addresses in each switch’s 4096-

address forwarding table, (with configurable address aging value in the

Series 2500 switches).

■ automatically negotiated full-duplex operation for the fixed 10/100 RJ-45

ports when connected to other auto-negotiating devices — the transceiver

ports always operate at full duplex.

■ the Series 2300 switches have a Download Port, through which you can

update your switch with the latest code, for any product enhancements

or bug fixes. (For the Series 2500 switches, you can download new code

through the Console port.)

The Series 2500 switches also include these network management features:

■ easy management of the switches through several available interfaces:

• web browser interface—an easy to use built-in graphical interface

that can be accessed from common web browsers.

• console interface—a full featured, easy to use, VT-100 terminal

interface that is especially good for out-of-band switch management

or for telnet access to the switch.

• HP TopTools for Hubs & Switches—an SNMP-based, graphical

network management tool that you can use to manage your entire

network. This product is included with your new switch.

■ support for the Spanning Tree Protocol to eliminate network loops

2353-ed2.book Page 8 Friday, February 9, 2001 6:00 PM

1-9

Introducing the HP ProCurve Series 2300 and 2500 Switches

Switch Operation Overview

Introducing the HP ProCurve

Series 2300 and 2500

■ support for up to 30 IEEE 802.1Q-compliant VLANs so you can divide the

attached end nodes into logical groupings that fit your business needs.

■ support for many advanced features to enhance network performance

and network traffic control—described in the Management and Config-

uration Guide that came with your Series 2500 switch.

■ download of new code for product enhancements or bug fixes.

Switch Operation Overview

Address Table Operation

Address Learning. As devices are connected to the switch ports, either

directly or through hubs or other switches, the MAC addresses of those

devices are learned automatically and stored in the 4096-entry address table

featured by the Series 2300 and 2500 switches. The switches also identify the

number of the port on which each address is learned so they know the network

location of each connected device.

Forwarding, Filtering, Flooding. When the switch receives a packet, it

determines the destination address and looks for the address in the address

table. Based on the port location of that address, the switch then determines

whether to forward, filter-out, or flood the packet.

■ forward - if the destination address is on a different port than the one on

which the packet was received, the packet is forwarded to the destination

port and on to the destination device.

■ filter out - if the destination address is on the same port as the one on

which the packet was received, the packet is filtered out. The switch

thereby isolates local traffic so the rest of the network connected to the

switch does not lose bandwidth dealing with unnecessary traffic.

■ flood - whenever a new destination address is found in a packet received

on a switch port, the destination address will not yet be in the switch’s

address table and the switch cannot know whether to forward or filter out

the packet. In this case, it sends the packet to all the other switch ports.

This is referred to as “flooding”. When the destination device receives the

packet, and it replies, the switch learns the new address from the reply

packet. Then, all future packets destined for that address are forwarded

or filtered out appropriately.

Note: Usually, multicast and broadcast packets are flooded, although

configuration of sofware features influence that behavior.

2353-ed2.book Page 9 Friday, February 9, 2001 6:00 PM

1-10

Introducing the HP ProCurve Series 2300 and 2500 Switches

Switch Operation Overview

Introducing the HP ProCurve

Series 2300 and 2500

Network Moves and Changes. When a PC, server, printer, or other

network device is moved in the network, and becomes connected to a different

switch port, the Series 2300 and 2500 switches automatically recognize the

change and update their address table with the new port location of the device.

Communication with the device is automatically maintained, without any

address table manipulation being required by the network administrator.

Effect of VLANs (Series 2500 only)

On the Series 2500 switches, if you configure multiple virtual LANs (VLANs)

on the switch, each VLAN behaves as a “logical switch” containing the switch

ports that you assign to it. Each logical switch behaves as an isolated broad-

cast domain, just as if it were a separate physical switch. The forward, filter,

and flood behavior described for the physical switch above, operates the same

for each of the logical switches defined by the VLANs: packets are forwarded

or flooded only to the ports that are within a given VLAN. Just as for separate

isolated physical switches, there is no communication between ports that are

in separate VLANs unless the VLANs are connected by an external router.

For more information on configuring VLANs and their behavior, see the

Management and Configuration Guide that came with your switch.

2353-ed2.book Page 10 Friday, February 9, 2001 6:00 PM

2-1

Installing the Series 2300

and 2500 Switches

Installing the Series 2300 and 2500 Switches

The HP Series 2300 and 2500 switches are easy to install. They each come with

an accessory kit that includes the brackets for mounting the switch in a

standard 19-inch telco rack, in an equipment cabinet, or on a wall, and with

rubber feet that can be attached so the switch can be securely located on a

horizontal surface. The brackets are designed to allow mounting the switch

in a variety of locations and orientations.

This chapter shows you how to install your Series 2300 and 2500 switches.

Included Parts

The Series 2300 and 2500 switches have the following components shipped

with them:

■ HP ProCurve Series 2300 and 2500 Switches Installation and Getting

Started Guide (5969-2353), this manual

■ Customer Support/Warranty booklet

■ Accessory kit (5064-2085)

• two mounting brackets

• four 8-mm M4 screws to attach the mounting brackets to the switch

• four 5/8-inch number 12-24 screws to attach the switch to a rack

• four rubber feet

■ Power cord, one of the following:

The Series 2500 switches have these additional components:

■ HP ProCurve Switch Series 2500 Management and Configuration

Guide (5969-2354)

■ HP TopTools for Hubs & Switches - CD ROM and enclosure

■ Console cable

Australia/New Zealand

China

Continental Europe

Denmark

Japan

8120-6803

8120-8377

8120-6802

8120-6806

8120-6804

Switzerland

United Kingdom/

Hong Kong/Singapore

United States/Canada/Mexico

8120-6807

8120-8709

8120-6805

2353-ed2.book Page 1 Friday, February 9, 2001 6:00 PM

2-2

Installing the Series 2300 and 2500 Switches

Installation Procedures

Installing the Series 2300

and 2500 Switches

Installation Procedures

Summary

Follow these easy steps to install your switch. The rest of this chapter provides

details on these steps.

1. Prepare the installation site (page 2-4). Make sure that the physical

environment into which you will be installing the switch is properly

prepared, including having the correct network cabling ready to connect

to the switch and having an appropriate location for the switch. Please see

page 2-3 for some installation precautions.

2. Install transceivers (optional—page 2-6). The switches have two

slots for installing any of the supported HP Gbps (gigabit) or 100 Mbps

transceivers. Depending on where you will install the switch, it may be

easier to install the transceivers first.

3. Verify that the switch passes self test (page 2-7). This is a simple

process of plugging the switch into a power source and observing that the

LEDs on the switch’s front panel indicate correct switch operation.

4. Mount the switch (page 2-9). The Series 2300 and 2500 switches can

be mounted in a 19-inch telco rack, in an equipment cabinet, on a wall, or

on a horizontal surface. The included mounting brackets allow mounting

the switch in a variety of locations and orientations.

5. Connect power to the switch (page 2-13). Once the switch is

mounted, plug it in to the nearby main power source.

6. Connect the network devices (page 2-14). Using the appropriate

network cables, connect the network devices to the switch ports.

7. Connect a console to the switch (optional, on Series 2500 switches

only—page 2-15). For your Series 2500 switch, you may wish to modify

the switch’s configuration, for example, to configure an IP address so it

can be managed using a web browser, from an SNMP network manage-

ment station, or through a Telnet session. Configuration changes can be

made easily by using the included console cable to connect a PC to the

switch’s console port.

At this point, your switch is fully installed. See the rest of this chapter if you

need more detailed information on any of these installation steps.

2353-ed2.book Page 2 Friday, February 9, 2001 6:00 PM

Page is loading ...

HP (Hewlett-Packard) Laptop 2500 User manual

Brand: HP (Hewlett-Packard)

Model: Laptop 2500

Category: Network switches

Type: User manual

This manual is also suitable for

2500

Download PDF

report

HP (Hewlett-Packard) Laptop 2500 User manual

This manual is also suitable for

HP (Hewlett-Packard) Laptop 2500 User manual

Related papers

Other documents