- 1 -
Language
English
Version V1.0
Update Aug.2008
………………………………………………
………………………………………………………………………………………………
………………………………………………
What’s on your package?
One PIO-D144/168 card
One companion PCI CD V 3.5
One Quick Start Guide(this document)
………………………………………………
………………………………………………………………………………………………
………………………………………………
Installing Windows Driver
Follow those steps:
I. Setup the Windows driver.
You can get the driver from:
CD:\NAPDOS\PCI\PIO-DIO\dll_ocx\Driver
http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/pio-dio/dll_ocx/driver/
1
11
1
2
22
2
PIO
-
D
144/168
- 2 -
II. Click button to start installation.
III. Click
button to install driver into the default
folder.
IV. Click
button to continue installation.
V. Click
button to reboot the PC.
………………………………………………
………………………………………………………………………………………………
………………………………………………
Installing Hardware on PC
Follow those steps:
I. Shut down your computer
II. Remove all covers from the computer
III. Select an unused PCI slot
IV. Carefully insert your I/O card into the PCI slot
V. Replace the PC cover
VI. Power on the computer
After powering-on the computer and the Plug&Play
steps finished.
3
33
3
Windows drive
r only support windows 98/NT/2000 and
XP/2003/Vista 32-bit version.
- 3 -
………………………………………………
………………………………………………………………………………………………
………………………………………………
Pin Assignments
4
44
4
TTL
Range
High(1)
Over 2.0V (But ,Over 5.0V
will damage the device)
None
Define
2.0V~0.8V
Low(0) Under 0.8V
All Signals are TTL compatible
.
Port No. PA0~7 PB0~7
PC0~7
CN1 Port 0 Port 1 Port 2
CN2 Port 3 Port 4 Port5
CN3 Port 6 Port 7 Port 8
CN4 Port 9 Port 10
Port 11
CN5 Port 12 Port 13 Port 14
CN6 Port 15 Port 16
Port 17
CN7
(D168 only)
Port 18 Port 19
Port 20
- 4 -
………………………………………………
………………………………………………………………………………………………
………………………………………………
Self-Test
I. Use CA-5002(Optional) to connect the CN5 with
CN6.
II. Run the DIO sample program.
Get the zipped file from:
CD:\NAPDOS\PCI\PIO-DIO\dll_ocx\Demo
http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/pio-dio/dll_ocx/demo/
III. Check number of the PIO-D144/168, and test DIO
function
5
55
5
CN
6
2
CN
5
1
CN
7
(D168 only)
CN
2
51
CN
3
51
CN
1
1
CN
4
51
- 5 -
IV. Get DIO function test result
Step1:
One PIO-D144/168
card had
successfully
installed to PC
Step2:
Select the board
number for the
PIO-D144/168.St
art from 0
Step
3
:
Click this button
to do DIO
function test
Complet
Output &h000000 to CN5,
Port 17,16,15 = &h0 &h0 &h0
Pass!!!!
Output &hFFFFFF to CN5,
Port 17,16,15 = &hFF &hFF &hFF
Pass!!!!
- 6 -
………………………………………………
………………………………………………………………………………………………
………………………………………………
Additional Information
PIO-D144/168 Card Product page:
http://www.icpdas.com/products/DAQ/pc_based/pio_d144.htm
http://www.icpdas.com/products/DAQ/pc_based/pio_d168.htm
CA-5002(Optional) page:
http://www.icpdas.com/products/Accessories/cable/cable_selection.htm
Documents:
CD:\NAPDOS\PCI\PIO-DIO\manual
CD:\NAPDOS\PCI\Manual
http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/pio-dio/manual/
Software:
CD:\NAPDOS\PCI\PIO-DIO\
http://www.icpdas.com/download/pci/piodio/index.htm
The ICP DAS Web Site
http://www.icpdas.com
Contact Us
Copyright ©2008 by ICP DAS Co., Ltd. All right are reserved
6
66
6
Technical support
Supplies and ordering information
Ways to enhance your device
FAQ
Application story
-
1
-
2
