Page is loading ...
INS #
Brand Logo
reversed out of
black
INS #
IB5160 01EN
Installation Instructions – Arbor Post Top
Instructions d’installation – Haut de poteau Arbor
Instrucciones de instalación – Luminaria para poste de rotonda
WARNING
Customer is responsible for engineering analysis
to confirm pole and fixture compatibility for all
applications. Serious bodily injury or property damage
may occur if the pole mounted luminaire is not
installed to a compatible new or existing pole specific
to the conditions of your installation and physical
location. Refer to our pole white paper WP513001EN
for additional support information.
WARNING
Make certain power is OFF before starting installation
or attempting any maintenance.
WARNING
Risk of fire/electric shock. If not qualified, consult an
electrician.
WARNING
Risk of Electric Shock – Disconnect power at fuse or
circuit breaker before installing or servicing.
WARNING
Risk of Burn – Disconnect power and allow fixture to
cool before servicing.
WARNING
Risk of Personal Injury – Fixture may become damaged
and/or unstable if not installed properly.
Do not mount luminaire within 6” of a
combustible surface.
Do not handle luminaire by the glass. Do not
touch LEDs.
ote:N These instructions do not claim to cover all
details or variations in the equipment, procedure,
or process described, nor to provide directions
for meeting every possible contingency during
installation, operation or maintenance. When
additional information is desired to satisfy a
problem not covered sufficiently for user’s purpose,
please contact your nearest representative.
ote:N This lighting fixture has been shipped complete
with one of several mounting options. Please follow
the installation instructions specific to the catalog
part that you ordered.
ote:N Care must be taken not to set lighting fixture down
on optical lenses or lift the fixture in the lens area.
ote:N Specifications and dimensions subject to change
without notice.
IMPORTANT: Read carefully before installing fixture. Retain for future reference.
GENERAL: Upon receipt of the fixture, thoroughly inspect for any freight damage which should be brought to the
attention of the delivery carrier. Compare the catalog description listed on the packing slip with the fixture label on the
housing to assure you have received the correct material.
SAFETY: This fixture must be wired in accordance with the National Electrical Code and applicable local codes and
ordinances. Proper grounding is required to insure personal safety. Carefully observe grounding procedure under
installation section.
APPLICATIONS: This lighting fixture is designed for outdoor lighting services, and should not be used in area of limited
ventilation or inside high ambient temperature enclosures. It must be stored in a dry location prior to installation. Do
not expose lighting fixture to rain, dust or other environmental conditions prior to installation and insertion of photo
control or shorting cap (if so equipped). Do not install the fixture near combustible materials or locate next to airflow
blocking surfaces within 6 inches. Best results will be obtained if installed and maintained according to the following
recommendations.
2
EATON IB516001EN Installation instructions
Installation Instructions – Arbor Post Top
INSTALLATION
This lighting fixture has been shipped complete with one
of several mounting options. Please follow the installation
instructions specific to the catalog part that you ordered.
ote:N Care must be taken not to set lighting fixture down
on optical lenses or lift the fixture in the lens area.
Tools required
Allen key 3/16”, #2 Phillips head screw driver and torque
wrench.
A. Post Mount Single Luminaire (3" O.D. Pole Top
Complete with 2-3/8" O.D. Tenon, Tenon Length Range
3" to 4" Only)
1. Pull three leads from luminaire tenon fitter and supply
leads from the pole tenon.
2. Connect supply wires to appropriate luminaire leads.
(Figure 1.)
Supply side ground wire to green luminaire lead.
Supply side neutral wire to white luminaire lead.
Supply side line voltage wire to black luminaire lead.
3. Once connections are completely made, carefully push
all wires down into the tenon.
4. Slip fit the fixture onto the tenon. (Figure 2.)
ote:N Make sure wires do not get pinched.
5. For luminaire with asymmetric optics, rotate the fixture
according to arrow mark on the dome towards the
street side. (Figure 3.)
6. Install six 3/8-24 x .375” set screws and tighten to
160 in-lbs. (Figure 4.)
7. Install six 3/8-24 x .1875” jam screws and tighten to
160 in-lbs. (Figure 4.)
CAUTION
Over tightening screws may cause fixture damage.
Figure 2.
Figure 3.
Figure 4.
Figure 1.
Fixture
2-3/8" Pole Tenon
Tenon Fitter
Neutral Wire
White
Black
Green
Ground Wire
Line Voltage
Wire
Pole Tenon
Street Side
STREET SIDE
Arrow mark on
the dome
(6) Jam
Screws
(6) Set
Screws
3
EATON IB516001EN Installation instructions
Installation Instructions – Arbor Post Top
B. Pole Mount Single Arm (4" or 5" O.D. Pole with
2-3/8" or 3" O.D. Tenon. Tenon Length Range 4" to 6"
Only)
1. If using pole with 2-3/8" tenon, slipfit the spacer
provided onto the tenon of the pole. If using a pole with
3" tenon, discard the spacer provided.
2. Pull supply wires from pole tenon through the hole.
3. Loosen and take off the cap from single arm bottom
hole. (Figure 5.)
4. Insert supply wires from the pole through the bottom
hole of single arm and pull them down through the cap
hole. (Figure 5.)
5. Slip fit the single arm onto pole tenon.
ote:N Make sure the supply wires do not get pinched.
6. Rotate the single support arm to desired position. If
using the spacer from step 1, line up the clearance
holes in the spacer with holes in the arm.
7. Install six 3/8-24 x 7/8” set screws to hold arm to pole
and tighten to 200 inch-lbs. (Figure 6). Use 7/8" long
set screws if tenon size is 2-3/8". Use 1/2" set screws if
tenon size is 3".
8. Install six 3/8-24 x 3/16” jam screws and tighten to
175 inch-lbs. (Figure 6.)
CAUTION
Over tightening screws may cause fixture damage.
9. Pull three leads from luminaire and insert into the arm
tenon and through the cap hole. (Figure 7.)
10. Slip fit the fixture onto the single arm tenon.
ote:N Make sure wires do not get pinched.
11. For luminaire with asymmetric optics, rotate the fixture
according to arrow mark on the dome towards the
street side. (Figure 8.)
Figure 5.
Cap
Three Supply
Wires
Single Support Arm
Pole Tenon
Figure 6.
(6) Set
Screws
(6) Jam
Screws
Single Support Arm
Figure 7.
Arbor Fixture
Three Leads
Three Leads
Single Support
Arm Tenon
Three Supply
Wires
Figure 8.
Street Side
Arrow mark on
the dome
STREET SIDE
4
EATON IB516001EN Installation instructions
Installation Instructions – Arbor Post Top
12. Connect supply wires to appropriate luminaire leads
(Figure 9.)
Supply side ground wire to green luminaire lead.
Supply side neutral wire to white luminaire lead.
Supply side line voltage wire to black luminaire lead.
13. Once connections are completely made, carefully push
all wires back into the arm’s hole where the cap was
removed from. Tighten the cap to close.
ote:N Make sure wires do not get pinched.
14. Install six 3/8-24 x 3/8” set screws to hold the luminaire
on arm tenon and tighten to 160 inch-lbs.
15. Install six 3/8-24 x 3/16” jam screws and tighten to
160 inch-lbs.
CAUTION
Over tightening screws may cause damage to the luminaire
or arm.
Figure 10.
Figure 11.
Figure 9.
C. Post Mount Twin Arm (4" or 5" O.D. Pole; 3" O.D.
Tenon Only, Tenon Length Range 4" to 6" Only)
1. Loosen and take off the two caps from twin arm.
2. Pull the supply wires from post’s tenon and split supply
connections into two with supply leads going in each
side of the arm. (Figure 10.)
3. Slip fit the twin arm onto post’s tenon and rotate the
twin arm to the desired position.
ote:N Make sure the supply wires do not get pinched.
4. Install eight 1/2-13 x 1-1/4” set screws to hold arm to
pole and tighten to 300 inch-lbs. (Figure 11.) Install eight
1/2-13 jam nuts onto the sets screws and torque to 325
inch-lbs.
ote:N Only install on a 3” tenon.
CAUTION
Over tightening screws may cause fixture damage.
5. Route the luminaires onto two arm’s tenons on both
sides.
ote:N Make sure wires do not get pinched.
Supply Wires
Cap
Twin Arm
Pole Tenon
Twin Arm
(8) Jam
Nuts
Pole
Fixture
Neutral Wire
White
Black
Green
Ground Wire
Line Voltage
Wire
Pole Tenon
(8) Set
Screws
5
EATON IB516001EN Installation instructions
Installation Instructions – Arbor Post Top
6. For luminaire with asymmetric optics, rotate the
fixtures according to arrow mark on the dome towards
the street side. (Figure 12.)
7. Use one of the two bottom most holes on the
luminaires as a template to drill a pilot hole into the
twin arm tenons (two places on the arm one on each
tenon). Use the drill bushing provided and insert it in
one of the bottom holes of the luminaire and drill a
3/16” pilot hole through the bushing into the tenon.
Drill the hole until the drill clears tenon wall on one
side. (Figure 13.)
8. Take out the drill bushing and use a 3/16” (.203) drill bit
to open up the pilot hole. Tap this hole to 1/4-20 UNC
thread. (Figure 13.)
9. Connect supply wires to appropriate luminaire leads.
(Figure 14.)
Supply side ground wire to green luminaire lead.
Supply side neutral wire to white luminaire lead.
Supply side line voltage wire to black luminaire lead.
Figure 14.
Fixture
Fixture
Neutral Wire
Neutral Wire
White
White
Black
Black
Green
Green
Ground Wire
Ground Wire
Line Voltage
Wire
Line Voltage
Wire
Pole
Figure 12.
Street Side
STREET SIDE
STREET SIDE
Arrow
mark on
the dome
Figure 13.
Drill Bushing
Detail 1:
Drill Pilot Hole
Detail 2:
Drill 3/16 &
Tap 1/4-20
Pilot Hole
Drilled Using
Drill Bushing
1/4-20 Set Screw
Drill 3/16”
Hole & Tap
1/4-20
Use 1 of the 2
Bottom Holes to Drill
as per Detail 1 & 2
6
EATON IB516001EN Installation instructions
Installation Instructions – Arbor Post Top
D. Post Mount Single Luminaire (Tenon Adapter for 4"
O.D. Pole; 2-3/8" or 3" OD Tenon. Tenon Length Range
3" to 4" Only)
1. If using pole with 2-3/8" tenon, slipfit the spacer
provided onto the tenon of the pole. If using a pole with
3" tenon, discard the spacer provided.
2. Pull the supply wires from post’s tenon through the
tenon adapter.
3. Slip fit the tenon adapter onto post’s tenon. (Figure 16.)
ote:N Make sure the supply wires do not get pinched.
4. Install four 3/8-24 set screws to secure the tenon
adapter to pole and tighten to 200 inch-lbs. Use 3/4"
long set screws if tenon size is 2-3/8". Use 3/8" set
screws if tenon size is 3".
Figure 16.
Pole Tenon
Supply Wires
Tenon Adapter
Figure 17.
Fixture
Neutral Wire
White
Black
Green
Ground Wire
Line Voltage
Wire
Pole
Tenon Adapter
Figure 15.
Twin Arm
Cap
Cap
Fixture
Fixture
10. Once connections are completely made, carefully push
all the wires back into the arm’s hole where the cap
was removed from. Tighten the caps to close twin
arm’s holes. (Figure 15.)
ote:N Make sure wires do not get pinched.
11. Use the 1/4-20 x 1-1/4 set screw provided for the hole
drilled in step 8 (Figure 13) and tighten until the screw
is flush to the outside surface in location. Install five
3/8-24 x 3/8” set screws to hold each luminaire on arm
tenon and tighten to 15 inch-lbs. (1.25 ft. lbs.)
ote:N Do not overtighten.
12. Install five 3/8-24 x 3/16” jam screws and tighten to
15 inch-lbs. (1.25 ft lbs).
ote:N Do not overtighten.
CAUTION
Over tightening screws may cause fixture damage.
CAUTION
Over tightening screws may cause fixture damage.
5. Pull the supply leads from bottom of luminaire and
connect to supply wires from the post. (Figure 17.)
Supply side ground wire to green luminaire lead.
Supply side neutral wire to white luminaire lead.
Supply side line voltage wire to black luminaire lead.
6. Once connections are completely made, carefully push
all wires down into tenon adapter and install luminaire
onto the tenon adapter.
ote:N Make sure wires do not get pinched.
7
EATON IB516001EN Installation instructions
Installation Instructions – Arbor Post Top
Figure 18.
Street Side
Arrow mark on
the dome
E. Wall Mount
1. Using wall mount plate as template, drill four holes in
the wall (Figure 19). Install appropriate wall anchors (not
provided). Silicone caulk around the junction box and
wall anchors.
2. Align the gasket and wall mount bracket on the wall
and pull supply wires through the center holes in the
wall or junction box.
3. Secure the wall plate to the wall with four 1/2-13 x
1-1/2" long bolts and six lock washers. Torque bolts to
37 ft. lbs.
ote:N Make sure the wires do not get pinched and
screws do not get over-tightened.
Figure 20.
Single Support Arm
Socket Head
Cap Screws
Cap
Supply Wires
Figure 19.
Single
Support
Wall Mount
Bracket
Supply
Wires
Gasket
Flat Washer
Lock Washer
Hex
Head
Screw
Wall
7. For luminaire with asymmetric optics, rotate the fixture
according to arrow mark on the dome towards the
street side. (Figure 18.)
8. Install six 3/8-24 x3/8” set screws to hold the luminaire
on arm tenon and tighten to 160 inch-lbs.
9. Install six 3/8-24 x 3/16” jam screws and tighten to 160
inch-lbs.
CAUTION
Over tightening screws may cause fixture damage.
STREET SIDE
4. Loosen and take off the cap from single support arm’s
bottom hole. (Figure 20.)
5. Extend supply wires from junction box to minimum of
3' in length.
6. Pull extended supply wires through the arm into the
hole where cap was placed (Figure 20.) and hook the
arm over installed wall plate.
ote:N Make sure wires do not get pinched.
7. Secure the arm by tightening the two screws on
bottom to approximately 17 ft lbs. towards the wall
plate. (Figure 20.)
8
EATON IB516001EN Installation instructions
Installation Instructions – Arbor Post Top
Figure 22.
Neutral Wire White
Black
Green
Ground Wire
Line Voltage
Wire
Three Leads from Fixture
Supply Wires from Wall
8. Pull the leads from luminaire through the tenon and cap
hole. (Figure 21.)
9. Slip fit the luminaire on the tenon of wall-mount arm.
ote:N Make sure the wires do not get pinched.
10. Connect supply wires to appropriate luminaire leads.
(Figure 22.)
Supply side ground wire to green luminaire lead.
Supply side neutral wire to white luminaire lead.
Supply side line voltage wire to black luminaire lead.
Figure 23.
Arrow mark on
the dome
Street Side
Figure 21.
Fixture
Single
Support
Arm’s Tenon
Three Leads
Three Supply Wires
STREET SIDE
11. Rotate the fixture in desired position. For luminaire with
asymmetric optics, rotate the fixture according to arrow
mark on the down towards the street side. (Figure 23.)
12. Once connections are completely made, carefully push
all wires down into single support arm. Tighten the cap
to close.
ote:N Make sure wires do not get pinched.
13. Install six 3/8-24 x 3/8” set screws to hold the luminaire
on arm tenon and tighten to 160 inch-lbs.
14. Install six 3/8-24 x 3/16” jam screws and tighten to 160
inch-lbs.
CAUTION
Over tightening screws may cause fixture damage.
Eaton
1121 Highway 74 South
Peachtree City, GA 30269
P: 770-486-4800
www.eaton.com/lighting
Canada Sales
5925 McLaughlin Road
Mississauga, Ontario L5R 1B8
P: 905-501-3000
F: 905-501-3172
© 2016 Eaton
All Rights Reserved
Printed in USA
Imprimé aux États-Unis
Impreso en los EE. UU.
Publication No. IB516001EN
April 23, 2016
Eaton is a registered trademark.
All trademarks are property
of their respective owners.
Eaton est une marque de commerce
déposée. Toutes les autres marques
de commerce sont la propriété de leur
propriétaire respectif.
Eaton es una marca comercial
registrada. Todas las marcas
comerciales son propiedad de sus
respectivos propietarios.
Product availability, specifications,
and compliances are subject to
change without notice
La disponibilité du produit, les
spécifications et les conformités
peuvent être modifiées sans préavis
La disponibilidad de productos, las
especificaciones y los cumplimientos
están sujetos a cambio sin previo aviso
Warranties and Limitation of Liability
Please refer to www.eaton.com/LightingWarrantyTerms for our terms and conditions.
Garanties et limitation de responsabilité
Veuillez consulter le site www.eaton.com/LightingWarrantyTerms pour obtenir les conditions générales.
Garantías y Limitación de Responsabilidad
Visite www.eaton.com/LightingWarrantyTerms para conocer nuestros términos y condiciones.
/
