2. iFixit
  3. HTC Wizard 200 Screen Cover Replacement
HTC Wizard 200 Screen Cover Replacement

iFixit HTC Wizard 200 Screen Cover Replacement User manual

  • Hello, I've reviewed the user guide for the HTC Wizard 200 screen cover replacement. This document provides detailed, step-by-step instructions on how to disassemble the device and replace the screen cover. It covers the use of specific tools and the proper handling of flexible connections. I am ready to answer your questions about this process or the device itself.
  • What tools are needed for screen cover replacement?
    How to remove the battery?
    What size screws are removed with T5 Torx screwdriver?
HTC Wizard 200 Screen Cover Replacement
Installation of the screen cover on the HTC Wizard 200.
Written By: Kyle Champ
HTC Wizard 200 Screen Cover Replacem…
Draft: 2022-05-26Guide ID: 6836 -
This document was generated on 2022-06-02 01:08:01 PM (MST).
© iFixit — CC BY-NC-SA www.iFixit.com Page 1 of 12
INTRODUCTION
This guide will explain how to install / remove the screen cover from the HTC Wizard 200.
TOOLS:
iFixit Opening Tool (1)
Spudger (1)
T5 Torx Screwdriver (1)
HTC Wizard 200 Screen Cover Replacem…
Draft: 2022-05-26Guide ID: 6836 -
This document was generated on 2022-06-02 01:08:01 PM (MST).
© iFixit — CC BY-NC-SA www.iFixit.com Page 2 of 12
Step 1 — Battery
To expose the battery, remove the outer case with your fingernail.
Remove the battery by pulling the black tab.
Step 2 — Back Panel
Insert the flat end of the spudger into
the two notches on the back of the
camera cover and pry them up.
HTC Wizard 200 Screen Cover Replacem…
Draft: 2022-05-26Guide ID: 6836 -
This document was generated on 2022-06-02 01:08:01 PM (MST).
© iFixit — CC BY-NC-SA www.iFixit.com Page 3 of 12
Step 3
Work the spudger around the edges of the camera cover until it comes off.
Step 4
Remove the four 6 mm screws with the T5 Torx screwdriver.
One of the screws is under the "void" sticker.
HTC Wizard 200 Screen Cover Replacem…
Draft: 2022-05-26Guide ID: 6836 -
This document was generated on 2022-06-02 01:08:01 PM (MST).
© iFixit — CC BY-NC-SA www.iFixit.com Page 4 of 12
Step 5
Insert the flat end of an iFixit opening tool between the side and inner covers to create a gap.
Work the tool around the edges until all the clips release.
Step 6
Once all the clips are open, remove the inner panel from the phone.
HTC Wizard 200 Screen Cover Replacem…
Draft: 2022-05-26Guide ID: 6836 -
This document was generated on 2022-06-02 01:08:01 PM (MST).
© iFixit — CC BY-NC-SA www.iFixit.com Page 5 of 12
Step 7 — Motherboard
Use the spudger to pry the camera
off.
Step 8
Using tweezers, flip the connector latch away from the motherboard.
Detach the flexible connection from under the connector latch.
HTC Wizard 200 Screen Cover Replacem…
Draft: 2022-05-26Guide ID: 6836 -
This document was generated on 2022-06-02 01:08:01 PM (MST).
© iFixit — CC BY-NC-SA www.iFixit.com Page 6 of 12
Step 9
Slide the keyboard into the open
position.
Step 10
Lift the motherboard out of the case using the spudger.
Expose the underside of the motherboard using your hands.
HTC Wizard 200 Screen Cover Replacem…
Draft: 2022-05-26Guide ID: 6836 -
This document was generated on 2022-06-02 01:08:01 PM (MST).
© iFixit — CC BY-NC-SA www.iFixit.com Page 7 of 12
Step 11
Remove the flexible connection from the motherboard.
Caution: Removing the connection too fast may cause damage to the connection and cables.
Step 12 — Keyboard Slider
Remove the four 5mm screws with the T5 Torx screwdriver.
Remove the keyboard slider from the main body.
HTC Wizard 200 Screen Cover Replacem…
Draft: 2022-05-26Guide ID: 6836 -
This document was generated on 2022-06-02 01:08:01 PM (MST).
© iFixit — CC BY-NC-SA www.iFixit.com Page 8 of 12
Step 13 — Screen Cover
Use the T5 Torx screwdriver to remove four 5mm screws that secure the back of the screen
casing.
Step 14
Insert the plastic opening tool between the front panel and the rear panel and pry open to reach the
screen.
HTC Wizard 200 Screen Cover Replacem…
Draft: 2022-05-26Guide ID: 6836 -
This document was generated on 2022-06-02 01:08:01 PM (MST).
© iFixit — CC BY-NC-SA www.iFixit.com Page 9 of 12
Step 15
Once the rear panel is loose, lift it off of the front panel.
The flexible connection will pop loose.
Step 16
Device rotated 90 degrees CCW.
Remove the yellow anti-static tape.
HTC Wizard 200 Screen Cover Replacem…
Draft: 2022-05-26Guide ID: 6836 -
This document was generated on 2022-06-02 01:08:01 PM (MST).
© iFixit — CC BY-NC-SA www.iFixit.com Page 10 of 12
Step 17
Unscrew the two 3mm phillips #0 screws from the bottom of the device that secure the rigid flex
board to the screen panel.
Step 18
Device rotated 180 degrees CW.
Unscrew the two 3mm phillips #0
screws from the top of the device
that secure the rigid flex board to the
screen panel.
HTC Wizard 200 Screen Cover Replacem…
Draft: 2022-05-26Guide ID: 6836 -
This document was generated on 2022-06-02 01:08:01 PM (MST).
© iFixit — CC BY-NC-SA www.iFixit.com Page 11 of 12
To reassemble your device, follow these instructions in reverse order.
Step 19
Device rotated 90 degrees CCW.
Unhinge the flexible connection and
use the tweezers to disconnect.
Step 20
Now that the rigid flex board is
loose, remove it from the screen.
HTC Wizard 200 Screen Cover Replacem…
Draft: 2022-05-26Guide ID: 6836 -
This document was generated on 2022-06-02 01:08:01 PM (MST).
© iFixit — CC BY-NC-SA www.iFixit.com Page 12 of 12
/