Ironside AUMC2040 User manual

Brand
Ironside
Model
AUMC2040
Type
User manual

Ironside AUMC2040 is a motorcycle lift that provides efficient and secure lifting of twin-spar framed motorcycles, allowing for repairs, servicing, and deep cleaning. It smoothly elevates the motorcycle to heights that are optimal for the user and is fully maneuverable. The lift is designed to be convenient to assemble and use and does not require any disassembly or repair without authorization. Ironside AUMC2040 has a maximum load capacity of 680 kg (1500 lb) and a lifting range of 146-420 mm.

Ironside AUMC2040 is a motorcycle lift that provides efficient and secure lifting of twin-spar framed motorcycles, allowing for repairs, servicing, and deep cleaning. It smoothly elevates the motorcycle to heights that are optimal for the user and is fully maneuverable. The lift is designed to be convenient to assemble and use and does not require any disassembly or repair without authorization. Ironside AUMC2040 has a maximum load capacity of 680 kg (1500 lb) and a lifting range of 146-420 mm.

TECHNICAL DATA
Max Load: 680 kg (1500 lb)
Lifting Range: 146-420 mm
FEATURE
1. The lift is designed to enable efficient and safe lifting of twin-spar framed
motorcycle , allowing repairs, servicing and extensive cleaning.
2. The lift smoothly and elevates the motorcycle to optimum heights to suit the user ,
and is fully maneuverable.
3. This product’s assembly and operation is very convenient, it is used to repair
motorcycle lifting tools.
OPERATION
1. Before using, open release valve, play on the pump to discharge air.
2. Push to motorcycle bottom, fixed support foot. Don't touch the site will be sharp
load.
3. Tighten release valve, step on playing pump foot pedals.
4. When the above table touch with cords, and bind living through orientated load can
be started.
5. Rise lift in a way, and open security support. Slowly unscrew release valve
counterclockwise.
6. When the load separate from the lift, the lift drop to the lowest.
7. Remove lift from motorcycle below.
***With pneumatic device: the joint of pump air directly receive to the air source.
then press enter the valve to work.
WARNING
1. Read, understand and comply with all instructions before using the lift for the first
time.
2. Without training , do not Operate without authorization.
3. Do not exceed specified weight.
4. This product is a temporary tool, not for long time support object tools.
5. Use only on hard, level surfaces. When using , fix support foot .
6. Before using, the lift drop to the lowest. Replace damaged parts and tighten all
loose bolts.
7. When dropped, please pay attention to control speed.
MAINTENANCE
1. Add adequate lubricant oil regularly to air pump to avoid air pump inside wear.
2. Clean piston tube in hydraulic ram , and avoid the piston tube rust.
3. When not using, the lift drop to the lowest, avoid piston corrosion.
4. Do not disassemble and repair without authorization in any operation and technical
matter.
TROUBLESHOOTING
Symptom
Possible cause
Corrective Action
Foot pump does not work
Air into the hydraulic
system
Unscrew the vent screw,
and exhaust air
Release valve will not be
tightened
Tighten the release valve
overload
Remove partial overload
Hydraulic system has
rubbish
Contact service
gas-operated pump can not
work
The piston and cylinder
seals wall is not
lubrication
In the intake pipe mouth
plus a small amount of
lubricant oil
Pressure in gas-operated
pump will not enough
Increasing pressure to
demand
Release valve will not be
tightened
Tighten the release valve
Hydraulic system has
rubbish
Contact service
Can’t rise to the highest
Oil lever too low
Add the hydraulic oil
MAIN PARTS
HYDRAULIC MOTORCYLE LIFT
INSTRUCTION MANUAL CE
RETAIN THIS MANUAL FOR FUTURE REFERENCE
PLEASE READ THIS MANUAL CAREFULLY BEFORE USE
State of lifting
State of drop
Oil filling vent
Pump with handle release valve
Safety support by manual operation
Bandage ring
  • Page 1 1
  • Page 2 2

Ironside AUMC2040 User manual

Brand
Ironside
Model
AUMC2040
Type
User manual

Ironside AUMC2040 is a motorcycle lift that provides efficient and secure lifting of twin-spar framed motorcycles, allowing for repairs, servicing, and deep cleaning. It smoothly elevates the motorcycle to heights that are optimal for the user and is fully maneuverable. The lift is designed to be convenient to assemble and use and does not require any disassembly or repair without authorization. Ironside AUMC2040 has a maximum load capacity of 680 kg (1500 lb) and a lifting range of 146-420 mm.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents