International Concepts CC-27P Operating instructions

International Concepts
Brand
International Concepts
Model
CC-27P
Type
Operating instructions

This manual is also suitable for

International Concepts CC-27P

The International Concepts CC-27P is a three-piece juvenile set that includes two chairs and a table. The chairs are made of sturdy wood and feature comfortable seats and crossbars for support. The table is also made of sturdy wood and has a spacious top that is perfect for playing games, eating, or doing homework.

This set is perfect for any child's room or playroom. It is durable and easy to assemble, and it is sure to provide hours of fun and enjoyment.

Here are some of the features of the International Concepts CC-27P:

  • Sturdy wood construction
  • Comfortable seats

International Concepts CC-27P

The International Concepts CC-27P is a three-piece juvenile set that includes two chairs and a table. The chairs are made of sturdy wood and feature comfortable seats and crossbars for support. The table is also made of sturdy wood and has a spacious top that is perfect for playing games, eating, or doing homework.

This set is perfect for any child's room or playroom. It is durable and easy to assemble, and it is sure to provide hours of fun and enjoyment.

Here are some of the features of the International Concepts CC-27P:

  • Sturdy wood construction
  • Comfortable seats
ITEM NO.: 2027
REVISED AUG 29, 2014
Printed in Vietnam
- 1 -
ASSEMBLY INSTRUCTIONS
Description
Item No.
:
THREE
-
PIECE JUVENILE SET
: 2027
ITEM NO.: 2027
REVISED AUG 29, 2014
Printed in Vietnam
- 2 -
BEFORE ASSEMBLY
Thank you for purchasing this quality product. This product has been designed for easy assembly and
constructed for durability. All parts were checked prior to packaging to insure quality. Prior to beginning
assembly, however, make sure all parts and hardware are included and free of obvious defect. If a part is
missing or defective, please contact the store where purchased. If hardware is missing, or you need help with
assembly, please call toll free 888-944-8396.
IMPORTANT NOTE:
- Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the parts from
being scratched.
- Remove all wrapping material, including staples & packing straps before you start to assemble.
- DO NOT tighten all screws and bolts until completely assembled.
- Keep all hardware parts out of reach of children.
WARNING:
Long exposure to rubber or soft plastic may cause a chemical reaction and damage the finish of your
table. Protect the surface of the table with cloth if you are using any product with rubber feet or base.
PART
LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
1/ CHAIR (per piece):
NO Description
Qt
y
Sketch NO Description Qty Sketch
A
Side frame
(L-R)
2
B
Front & back
apron
2
C
Crossbar 1
D
Top crossbar 1
E
Wood seat 1
2/ TABLE:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
F
Top
1
G
Leg frame
(L-R)
2
H
Center
crossbar
1
ASSEMBLY TOOLS REQUIRED
NOT INCLUDED
ITEM NO.: 2027
REVISED AUG 29, 2014
Printed in Vietnam
- 3 -
HARDWARE LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have all of the following hardware in a large bag:
1/ CHAIR: totally same in 2 small bags, for 2 chairs
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
1
Bolt
(M6x50mm)
6
2
Screw
(M4x35mm)
4
3
Barrel nut
( M6x13mm)
6
4
Allen key
(4x80mm)
1
2/ TABLE
:
in a small bag
NO Description Qty Sketch NO Description Qty Sketch
1
Bolt
(M6x50mm)
6
2
Screw
(M4x35mm)
6
3
Barrel nut
( M6x13mm)
6
4
Allen key
(4x80mm)
1
STEP1-chair
Attach stretchers (B), and crossbar (D) to the 1st side frame (A) with bolts (1) and nuts (3). Tighten with
Allen key (4) as shown below.
Note: DO NOT fully tighten any of the bolts, until the chair is assembled, then put on a flat level
surface to make sure the chair is level and then tighten the bolts.
ITEM NO.: 2027
REVISED AUG 29, 2014
Printed in Vietnam
- 4 -
STEP 2 - chair
Attach crossbar (C) to the 1
st
side frame (A). Then attach the 2
nd
side frame (A) to the unit with bolts
(1), and nuts (3). Tighten with Allen key (4).
STEP 3
-
chair
Attach the seat (E) to top of the seat frame (from Step 2) with screws (2). Tighten with a screwdriver.
ITEM NO.: 2027
REVISED AUG 29, 2014
Printed in Vietnam
- 5 -
STEP 4 – table
Attach leg frames (G) to the top (F) with bolts (1), and nuts (3). Tighten with Allen key (4).
Attach center crossbar (H) to the leg frames (G) with bolts (1) and nuts (3). Tighten with Allen key (4).
UYO
STEP 5
–
table
Attach aprons of leg frames (G) to top (F) with screws (2). Tighten with a screwdriver as shown below.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

International Concepts CC-27P Operating instructions

International Concepts
Brand
International Concepts
Model
CC-27P
Type
Operating instructions
This manual is also suitable for

International Concepts CC-27P

The International Concepts CC-27P is a three-piece juvenile set that includes two chairs and a table. The chairs are made of sturdy wood and feature comfortable seats and crossbars for support. The table is also made of sturdy wood and has a spacious top that is perfect for playing games, eating, or doing homework.

This set is perfect for any child's room or playroom. It is durable and easy to assemble, and it is sure to provide hours of fun and enjoyment.

Here are some of the features of the International Concepts CC-27P:

  • Sturdy wood construction
  • Comfortable seats
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents