Goldberg Brothers Inc. GB60055RSS Installation guide

GOLDBERG BROTHERS, INC.

Goldberg Brothers Barn Door Hardware sets come with a one-year manufacture’s

warranty for defective parts under normal installation and use. Warranty is subject to

repair or replacement of defective part/s at manufacture’s discretion and does not include

installation costs. Goldberg Brothers does not warrant the loss of ﬁnish at points where

roller is in contact with the track. Goldberg Brothers Barn Door Hardware is sold as a

rustic ﬁnished hardware and Goldberg does not warrant the imperfections seen through

the ﬁnish in steel parts. It is part of the look.

This document contains proprietary information of Goldberg Brothers, Inc. and its receipt

of possession does not convey any rights to reproduce or disclose its contents, or to

manufacture, use or sell anything it may describe. Reproduction, disclosure, or use

without prior written authorization from Goldberg Brothers, Inc. is strictly forbidden.

Included Hardware

Straight strap hangers (2) T-guide (1) Carriage bolts (4) Washers (6) An-jump blocks (2) Spacers (6)

Track stops (2) T-guide screws (2) Hex lag bolts (6) Cap nuts (4) An-jump block screws (4) Hex key wrench (1)

Bumper:

Place 1 pad on stop

or edge of roller per side.

Stay:

Place 1 pad on top of track at

each end directly under roller

when roller is touching stop.

Bumper

Stay

DOOR

TRACK

Finished Opening

DOOR EDGE

½ʺ

1ʺ

⁄ʺ

⁄ʺ

⁄ʺ

⁄ʺ

⁄ʺ

Using the T-guide screws, a ach the T-guide to the ﬂoor

by aligning the edge of the guide with the edge of

ﬁnished opening as shown above.

finished floor

WALL

DOOR

FINISHED FLOOR

Plumb the door before fastening door guide to ﬂoor.

Goldberg Brothers, Inc.

10488 W Cennt

enial Rd, Suite 100

Lileton, CO 80127

(303) 321-1099

In the closed posion

the door should

overlap the wall a

minimum of 3/8” at

the top and a

minimum of 1/2” on

both sides

The edge of the door

should align with the

end of the track

Note: Aer the door

is hung from the

track the an-jump

blocks can be

installed directly

behind the straight

strap hanger

3ʺ from both sides of the top half of the door,

measure down 1⁄ʺ and 4ʺ and drill ⁄ʺ pilot holes

followed by ⁄ʺ pilot holes.

For large projects install templates are available for

purchase.

4ʺ

1⁄ʺ

3ʺ

Door Prep and Hanger Installaon

T-guide Installaon

Basic Install Layouts

Stainless Steel Straight Strap - Installation Instructions

Standard Hardware Pack

installed with no casing,

base, or other trim.

FINISHED OPENING

HEADER/BLOCK

WALL

DOOR

Standard Hardware Pack

installed on track trim board that is

equal to or thicker than casing,

base, or other trim.

FINISHED OPENING

HEADER/BLOCK

WALL

DOOR

Head Track Block

SIDE CASING

Base Board

Standard Hardware Pack +

Extension Kit installed where casing, base,

or other trim is greater than .

Extensions

FINISHED OPENING

HEADER/BLOCK

WALL

½ʺ Extensions

DOOR

Side Casing

Base Board

Standard Hardware Pack + ½”Extension Kit

installed where casing, base, or

other trim is up to ½” thick.

⁄ʺ or 1⁄ʺ

⁄ʺ

⁄ʺ

⁄ʺ

⁄ʺ

FINISHED OPENING

HEADER/BLOCK

WALL

DOOR

SIDE CASING

BASE BOARD

Using the carriage

bolts, cap nuts and

provided allen

wrench, aach the

straight strap hangers

to the door as shown

in the diagram.

In the closed

posi on, the door

should overlap the

wall a minimum of

⁄ʺ at the top and a

minimum of ⁄ʺ on

both sides.

The edge of the door

should align with the

end of the track.

Note: Aer the door

is hung from the

track, the an-jump

blocks can be

installed directly

behind the straight

strap hanger.

In the closed posion

the door should

overlap the wall a

minimum of 3/8” at

the top and a

minimum of 1/2” on

both sides.

The edge of the door

should align with the

end of the track.

Note: Aer the door

is hung from the

track the an-jump

blocks can be

installed directly

behind the straight

strap hanger.

DOOR

TRACK

FINISHED OPENING

DOOR EDGE

½ʺ

3ʺ

³⁄″

⁄ʺ

1⁄ʺ

1⁄ʺ

2⁄ʺ

⁄″

Goldberg Brothers barn door track and hardware sets come with a one-year manufacturer’s

warranty for defective parts under normal installation and use. Warranty is subject to repair

or replacement of defective components at manufacturer’s discretion and does not include

installation costs.

Goldberg Brothers does not warrant the loss of finish at points where roller is in contact

with track. Goldberg Barn Track is sold as a rustic finished hardware and Goldberg does not

warrant the imperfections seen through the finish in the steel parts. It is part of the look.

With the exception of our stainless steel products, Goldberg Brothers does not warrant any

products installed and used outdoors or where they are exposed to weather, running water

or water condensation. Under these conditions, rust and other damage will naturally occur.

This warranty does not include loss or defects caused by elements outside the control of

Goldberg Brothers, Inc., such as natural disasters, weather, fire, water leakage, abuse,

improper installation, or anything else deemed out of the control of Goldberg Brothers, Inc.

Using the T-guide screws, attach the T-guide to the

ﬂoor by aligning the edge of the guide with the edge

of the ﬁnished opening as shown above.

T-guide Installaon

Stay:

At each end of the track,

place one felt pad strip on

top of the track, 1⁄ʺ in from

the track stop as shown.

1⁄ʺ

An-jump block

Goldberg Brothers barn door track and hardware sets come with a one-year manufacturer’s

warranty for defecve parts under normal installaon and use. Warranty is subject to repair

or replacement of defecve components at manufacturer’s discreon and does not include

installaon costs.

Goldberg Brothers does not warrant the loss of ﬁnish at points where roller is in contact with

track. Goldberg Barn Track is sold as a rusc ﬁnished hardware and Goldberg does not

warrant the imperfecons seen through the ﬁnish in the steel parts. It is part of the look.

With the excepon of our stainless steel products, Goldberg Brothers does not warrant any

products installed and used outdoors or where they are exposed to weather, running water

or water condensaon. Under these condions, rust and other damage will naturally occur.

This warranty does not include loss of defects caused by elements outside the control of

Goldberg Brothers, Inc., such as natural disasters, weather, ﬁre, water leakage, abuse,

improper installaon, or anything else deemed out of the control of Goldberg Brothers, Inc.

2ʺ

Oponal Accessories

Sidewall Guide Bracket

1 each

Includes 1 bracket,

4 machine screws, 4 nuts and 1

felt pad

Part #6005SW

NOTE: Use the

provided T-guide

wood screws for

sidewall guide

installaon.

Door Guide “U”

1 set

Includes 2 “U” guides, 2 wood screws

and 1 felt pad

Part #6005U

NOTE: Use the provided

T-guide wood screws for U-guide

installaon.

Track Connecng Plate

1 each

Part #6005C

Wall Extension Bolts Set

Includes 6 lag bolts and 6 wall spacers

So Stop

1 set

Includes 2 So Stop mechanisms,

2 triggers and 4 wood screws

Part #6005SOFT11 (4’-7’ track)

Part #6005SOFT17 (8’+ track)

* Indicates that the related part is available is various colors.

Li the

door and hang it

from the track.

⁄ʺ

DH + 1⁄” = Track centerline

Track Installaon

Goldberg Brothers, Inc.

10488 W Centennial Rd, Suite 100

Lileton, CO 80127

(303) 321-1099

Track Centerline

1⁄ʺ Door

1⁄ʺ Door

2⁄ʺ Door

⁄ʺ Extension

Part #60053E

Part #60053EX

Part #60053EXX

⁄ʺ Extension

Part #60054E

Part #60054EX

Part #60054EXX

1⁄ʺ Extension

Part #60055E

Part #60055EX

Part #60055EXX

NOTE:

The end of the track

should extend a minimum

of ⁄” past the door

opening as noted above.

Using the stop cap,

stop spacers, and

stop bolt, aach the

stop as shown in the

diagram.

Using a hex lag bolt,

track, spacer and

washer, connect one

end of the track to

the wall using the

pre-drilled hole

closest to the

opening as shown in

the diagram.

Using the

same method

as before, connect

the opposite end of

the track to the wall.

Using the

remaining hex lag

bolts, spacers and

washers, ﬁnish

aaching the track

at the remaining

connecng points.

⁄ʺ Extension

⁄ʺ Extension

1⁄ʺ Extension

1⁄ʺ Door

Part #60053E

Part #60053EX

Part #60053EXX

1⁄ʺ Door

Part #60054E

Part #60054EX

Part #60054EXX

2⁄ʺ Door

Part #60055E

Part #60055EX

Part #60055EXX

Swing the track

to the opposite

end of the wall

as shown.

Mark the centerline* of the

track on the wall using a level.

*The centerline of the

Track is represented

as the door

height (DH) +1¾ʺ

above ﬁnished ﬂoor.

At each of the track

connecting points, drill ⁄ʺ

pilot holes followed

by ⁄ʺ pilot holes.

FINISHED FLOOR

Goldberg Brothers Inc. GB60055RSS, GB60050RSS, GB60053H4SS, GB60053RSS, GB60054H4SS, GB60054RSS, GB60055H4SS Installation guide

Related papers

Other documents