Goldberg Brothers Inc. GB60013H54SM Installation guide

Brand: Goldberg Brothers Inc.

Model: GB60013H54SM

Type: Installation guide

Mark the

centerline* of the

track on the wall

using a level.

door height + 1⁄”.

At the track

connecng points

drill ⁄” pilot holes

followed by ⁄”

pilot holes.

FINISHED FLOOR

*The centerline of

the Track is

represented as

Goldberg Brothers Barn Door Hardware sets come with a one-year manufacture’s

warranty

for defective parts under normal installation and use. Warranty is subject to

repair or replacement of defective part/s at manufacture’s discretion and does not include

installation costs. Goldberg Brothers does not warrant the loss of ﬁnish at points where

roller is in contact with the track. Goldberg Brothers Barn Door Hardware is sold as a

rustic ﬁnished hardware and Goldberg does not warrant the imperfections seen through

the ﬁnish in steel parts. It is part of the look.

This document contains proprietary information of Goldberg Brothers, Inc. and its receipt

of possession does not convey any rights to reproduce or disclose its contents, or to

manufacture, use or sell anything it may describe. Reproduction, disclosure, or use

without prior written authorization from Goldberg Brothers, Inc. is strictly forbidden.

303-321-1099

Goldberg Brothers, Inc.

10488 W. Centennial Rd Suite 100

Lileton, CO 80127

See opposite side for door

and hanger installaon.

Li the door and

hang it from the track.

Finish aaching the

track at the

remaining

connecng points.

Connect the

track to the wall

at the end by

the door

opening as

shown in the

diagram.

Using the same

method connect

the opposite

end of the track

to the wall as

shown.

NOTE:

The end of the

track should

extend ⁄” past of

the door opening.

⁄”

Included Hardware

J-strap hangers (2) T-guide (1) Carriage bolts (4) Washers (6) An-jump blocks (2) Spacers (6) Felt Pads (2)

Track stops (2) T-guide screws (2) Lock washers (4) Hex lag bolts (6) An-jump block screws (4) Hex nuts (4) Rubber bumper bands (2)

Using the carriage

bolts, hex nuts and

lock washers, aach

the J-strap hangers to

the door as shown in

the diagram.

DOOR

TRACK

Door Edge

3”

1”

3 ½”

1 ⁄”

1 ⁄”

Stay:

Place 1 pad on top of track at

each end 1.

DOOR

TRACK

FINISHED OPENING

DOOR EDGE

½ʺ

1ʺ

⁄ʺ

⁄ʺ

⁄ʺ

⁄ʺ

⁄ʺ

Using the T-guide screws, aach the T-guide to the ﬂoor

by aligning the edge of the guide with the edge of the

ﬁnished opening as shown above.

finished floor

WALL

DOOR

FINISHED FLOOR

Plumb the door before fastening door guide to ﬂoor.

Hanger Installation

T-guide Installation

Std Hardware Pack

installed with no casing,

base, or other trim.

Finished Opening

Header / Block

WALL

DOOR

Std Hardware Pack installed on track

trim board that is equal or thicker than

casing, base, or other trim.

Finished Opening

Header / Block

WALL

Head Track Block

Side Casing

Base Board

DOOR

Std Hardware Pack + ½”Extension Kit

installed where casing, base, or

other trim, is up to ½” thick .

Finished Opening

Header / Block

WALL

½ ʺ Extensions

DOOR

Side Casing

Base Board

Std Hardware Pack + 7/8” Extension Kit

installed where casing, base, or

other trim, is 5/8” to 1” thick .

Finished Opening

Extensions

Header / Block

WALL

DOOR

Side Casing

Base Board

⁄ ʺ

10488 W Cennt

enial Rd, Suite 100

Lileton, CO 80127

Goldberg Brothers, Inc.

(303) 321-1099

In the closed posion,

the door should

overlap the wall a

minimum of ⁄ʺ the top

and a minimum of ⁄ʺ

on both sides.

The edge of the door

should align with the

end of the track.

J-strap hanger.

Note: Aer the door is

hung from the track,

the an-jump blocks

can be installed

directly behind the

3ʺ from both sides of the top half of the door,

measure down 1⁄ʺ and 5⁄ʺ and drill ⁄ʺ pilot holes

followed by ⁄ʺ holes.

For large projects, installaon templates are

available for purchase.

5⁄ʺ

1⁄ʺ

3ʺ

Door Prep and Hanger Installaon

T-guide Installaon

Basic Installaon Layouts

Premium hardware set

installed with no casing,

base, or other trim.

FINISHED OPENING

HEADER/BLOCK

WALL

DOOR

Premium hardware set installed to

track trim board that is equal to, or thicker

than casing, base, or other trim.

FINISHED OPENING

HEADER/BLOCK

WALL

DOOR

Head Track Block

SIDE CASING

Base Board

Premium hardware set +

extension

kit installed where casing, base, or

other trim is greater than .

FINISHED OPENING

Extensions

Header / Block

WALL

DOOR

Side Casing

Base Board

FINISHED OPENING

HEADER/BLOCK

WALL

½ʺ Extensions

DOOR

Side Casing

Base Board

Premium hardware set + ½” extension

kit installed where casing, base, or

other trim is up to ½ʺ thick.

⁄ʺ or 1⁄ʺ

⁄ʺ

⁄ʺ

⁄ʺ

⁄ʺ

Attach the

exposed roller

hangers and anti-

jump blocks to the

door as shown in

3” from both sides of the top half of the door,

measure down 1⁄” and 5” and drill ⁄” pilot holes

followed by ⁄” pilot holes

For large projects door templates are available

for purchase

4”

1-⁄”

2-⁄”

FINISHED OPENING

HEADER/BLOCK

WALL

DOOR

SIDE CASING

BASE BOARD

5⁄ʺ

2ʺ

An-jump

block

Stay felt

pad

Bumper felt pad

Stay:

At each end of the track,

place one felt pad strip on

top of the track, 1⁄ʺ in from

the track stop as shown.

An-jump block

For each hanger, place one felt pad

strip on the track stop or the edge

of the hanger as shown.

Place one of the provided rubber

bumper bands around each stop.

Bumper:

1⁄ʺ

This warranty does not include loss or defects caused by elements outside the control of

Goldberg Brothers , such as natural disasters, weather, ﬁre, water leakage, abuse, improper

installaon, or anything else deemed out of the control of Goldberg Brothers.

With the excepon of our stainless steel products, Goldberg Brothers does not warrant any

products installed and used outdoors or where they are exposed to weather, running water

or water condensaon. Under these condions, rust and other damage will naturally occur.

Goldberg Brothers does not warrant the loss of ﬁnish at points where roller is in contact with

track. Goldberg Brothers barn door hardware is sold as a rusc ﬁnished hardware and

Goldberg Brothers does not warrant the imperfecons seen through the ﬁnish in the steel

parts. It is part of the look.

Goldberg Brothers barn door track and hardware sets come with a one-year manufacturer’s

warranty for defecve parts under normal installaon and use. Warranty is subject to repair

or replacement of defecve components at manufacturer’s discreon and does not include

installaon costs.

GOLDBERG BROTHERS BARN DOOR HARDWARE

Premium Series J-strap hardware set - Installation Instructions

60013H-*, 60014H-*, 60015H-*, 60015UH-*

Attach the exposed

roller hangers to the

door

DOOR

TRACK

Door Edge

3”

1”

3 ½”

Aach the exposed

roller-hangers and

an-jump blocks to the

door as shown in the

diagram.

Aach T-guide to ﬂoor by aligning edge of guide with

edge of opening as shown above.

finished floor

T-guide flush to finished opening

WALL

DOOR

3/8”

1/4”

7/8”

FINISHED FLOOR

Plumb door before fastening door

guide to ﬂoor

3” from both sides of the top half of the door,

measure down 1⁄” and 5” and drill ⁄” pilot holes

followed by ⁄” pilot holes.

For large projects install templates are available

for purchase.

5”

1⁄”

3”

Oponal Accessories

Sidewall guide bracket

4 machine screws, 4 nuts, and 1

felt pad

Part #6001SW-*

NOTE: Use the

provided T-guide

screws for

Includes 1 bracket,

1 each

sidewall guide installaon.

Part #6001U-*

Door U-guide

NOTE: For U-guide installaon

use the T-guide screws provided

in the hardware set.

Includes 2 U-guides, 2 wood screws

and 1 felt pad

1 set

Track Connecng Plate

1 each

Part #6001C-*

Track Extension Kits

Includes 6 lag bolts and 6 spacers

1 set

So Stop

2 triggers, 4 wood screws

Part #6001SOFT17 (8’+ track)

Includes 2 So Stop mechanisms,

Part #6001SOFT11 (4’-7’ track)

* Indicates that the related part is available in various colors.

1 ⁄”

1 ⁄”

Li the door and

hang it from the track.

Using the

remaining hex lag

bolts, spacers, and

washers, ﬁnish

aaching the track

at the remaining

connecng points.

Using the same

method, aach

the opposite end

of the track to the

wall as shown.

Using a hex lag bolt, track

stop, spacer, and washer,

aach one end of the track

to the wall using the pre-

drilled hole closest to the

opening as shown in the

diagram.

NOTE:

The end of the track

should extend a minimum

of ⁄” past the door

opening as noted above.

⁄ʺ

Mark the centerline* of the

track on the wall using a level.

*The centerline of the track is

represented as the door

height (DH) + 1⁄ʺ above

ﬁnished ﬂoor.

At each of the track

connecng points, drill ⁄”

pilot holes, followed

by ⁄ʺ pilot holes.

DH + 1⁄” = track centerline

FINISHED FLOOR

Track Installaon

Goldberg Brothers, Inc.

10488 W Cen

tennial Rd, Suite 100

Lileton, CO 80127

(303) 321-1099

Track Centerline

1⁄ʺ door

1⁄ʺ door

2⁄ʺ door

⁄ʺ extension

Part #60013E-*

Part #60013EX-*

Part #60013EXX-*

⁄ʺ extension

Part #60014E-*

Part #60014EX-*

Part #60014EXX-*

1⁄ʺ extension

Part #60015E-*

Part #60015EX-*

Part #60015EXX-*

Swing the

track to the

opposite end

of the wall as

shown.

06/19/19

Goldberg Brothers Inc. GB60013H54SM Installation guide

Goldberg Brothers Inc. GB60013H54SM Installation guide

Goldberg Brothers Inc. GB60013H54SM Installation guide

Related papers

Other documents