i3 International Ax401C1M User manual

Brand: i3 International

Model: Ax401C1M

Type: User manual

i3 International Ax401C1M is a high-quality network camera with a range of features for clear and versatile surveillance. With its 1/3" progressive transfer CCD image sensor, it delivers crisp images in both SXVGA and VGA resolutions. The camera supports motion detection and two-way audio, making it ideal for security applications. It also has an SD card slot for local storage of recordings. With its PoE+ capability, the camera can be powered over a single Ethernet cable, simplifying installation.

C-AX401C1M

Network Camera User Guide

WARNING:

Before attempting to connect or operate this product, read these instructions carefully.

Save this manual for future use.

To avoid electrical shock and to preserve the product warranty, DO NOT disassemble the camera.

Refer servicing to qualified personnel only.

CONTENTS

PRECAUTIONS

NOTES OF USE

NETWORKING

SETTINGS

SPECIFICATIONS

PRECAUTIONS

This equipment has been tested and found to comply with the limits

for a Class A digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio

communications.

Operation of this equipment in a residential area is likely to cause

harmful interference, in which case users will be required to correct the

interference at their own expense.

FCC Caution:

To ensure continued compliance, use only shielded interface cables

when connecting to computer or peripheral devices. Any changes

or modications not expressly approved by the party responsible for

compliance could void the user’s authority to operate this equipment.

The serial number of this product may be found on top of the unit. It is

recommended that you note the serial number of this unit in the space

provided and retain this book as a permanent record of your purchase to

aid identication in the event of theft.

Model No.

Serial No.

Date of Purchase:

NOTES OF USE

Power Supply

Ensure the supplied voltage meets the power consumption requirements of this

camera before powering the camera on. Incorrect voltage may cause irreparable

damage to the video camera and will effectively void the camera warranty

Operating or storage location

Avoid shooting very bright objects (such as light ttings) for an extended pe-

riod. Avoid operating or storing the unit in the following locations:

• Extremely hot or cold places (operating temperature: -10

C to +50

• Close to sources of strong magnetism

• Close to sources of powerful electromagnetic radiation, such as

radios or TV transmitters

• Close to humid or excessively dusty places

• Where exposed to mechanical vibrations

• Close to uorescent lamps or objects reecting light

• Under unstable light sources (may cause ickering)

Transportation

When transporting the camera, repack it as originally packed at the

factory, or in materials equal in quality.

Cleaning

• For maximum optical clarity, the dome cover must remain clean. Use

a soft, dry cloth to remove nger prints or dust from the dome cover.

• Use a blower to remove dust from the lens.

• Clean the body with a soft, dry cloth. If it is very dirty, use a cloth

dampened with a small quantity of neutral detergent, then wipe dry.

• Do not use volatile solvents such as alcohol, benzene, or thinners,

as they may damage the surface nishes.

Servicing

To avoid electrical shock and to preserve the product warranty, DO NOT

disassemble the camera. Refer servicing to qualied personnel only.

NOTES OF USE

Included in the box

1. Camera (C-Ax401C1M)

2. Software CD

3. Quick start guide

Feature & Functions

SD card slot

Power (White:-/Red:+)

Network

Default Button Reset Button

Power Indicator

TV/IP Select

AL. I(Alarm In) &

AL. O(Alarm Out)

Audio In

(White)

Audio Out

(Black)

Power 24VAC 12VDC

Red 24VAC Positive

White 24VAC Negative

NETWORKING

Connecting to a camera using a network

1. Connect the camera to a PoE (Power over Ethernet) enabled switch or

router using a RJ45 Cat5 or Cat6 connection cable.

1.1. Connect the users computer to the PoE switch or router.

1. Connect the camera to a personal computer or a switch or router using

a RJ45 Cat5 or Cat6 connection cable.

1.1. Connect a properly grounded 24Volt AC power source to the camera.

Operating or storage location

2. Use the Annexxus Finder located on this CD to nd the Camera’s IP

address (default is 192.0.0.64)

3. Open an internet browser and type the IP Address of the camera into

the address bar. Hit enter.

NETWORKING

4. If you cannot connect try the following:

4.1. Wait. sometimes the router or switch will take a few seconds to

refresh the routing table

4.2. Go to control panel, network connections, and properties of the LAN

or WAN the camera is connected to. Under the Internet Protocol

(TCP/IP) properties, change the 2nd section of the IP to match the

same as your camera EG IP: 192.0.0.90 Camera: 192.0.0.64

4.3. Check the connection. Ensure all cables are properly connected.

5. Login to the camera using the proper username and password

5.1. Default Username: admin

5.2. Default Password: 1234

Network connections

SPECIFICATIONS

The specifications are subjects to be change without notice

Camera

Synch System Internal

Image Sensor 1/3" progressive transfer CCD

Number of Effective Pixels Full scanning mode: 1280 (H) x 960 (V)

Lens Optional Mega-Pixel Lens: f=2.4~6mm, F1.2, f=3.0 ~ 8 mm, F1.0,

f=5~50mm F1.4

Frame rate Motion Jpeg: SXVGA 1280 X 960 @15 fps

VGA (640 X 480)@30fpsMPEG-4:VGA 640x 480 @30fps

Motion detection Yes

Image Compression Method MJPEG / MPEG4

White Balance 2500K~10000K

Angle of view 27.73~100.18 (H) X 20.45 ~ 73.33 (V)

Software

Web Browser IE 6.0 or above, Netscape 7.0 or above

Password Protection Multiple password for user to login

Network

Ethernet 1 x 10/100 base-T Ethernet connection for LAN/WAN

Image compression method MJPEG / MPEG4

Protocol TCP/IP, UDP/IP, HTTP, SMTP, DNS, DHCP, NTP, DDNS, FTP, RTP

Connectors Screw less Terminal Jack

Environment

Weight 450g (1 lb)

Operating Temperature -10ºC ~ 50ºC (14ºF~122ºF)

Storage Temperature -20ºC ~ 60ºC (-4ºF ~ 140ºF)

Humidity 80% RH or less

Dimensions 180mm x 66mm x 55mm (7.09” x 2.6” x 2.17”)

Electrical

Audio Two-way mono audio; Full-duplex

Alarm Yes, 1 x Alarm in, 1 x Alarm out

SD card slot Yes, SD card up to 2GB supported

Power Requirement DC12V/AC24V/PoE+

Power Consumption Approx. 8W

Electric Shutter PAL:1/25, 1/50, 1/120, 1/250,1/1000, 1/10000 sec

NTSC:1/30, 1/60, 1/120, 1/250,1/1000, 1/10000 sec

Black light compensation Off, BLC1~BLC6, Auto

SPECIFICATIONS

Interface

Network Port RJ45 with LEDs

Video Port BNC

Audio IN & OUT Ports 3.5mm phone jack

Alarm IN & OUT Ports 1x Alarm In / 1x Alarm out

i³ INTERNATIONAL INC.

1.866.840.0004

www.i3international.com

Canada 780 Birchmount Road,

Unit 16, Scarborough,

ON, M1K 5H4

U.S.A. 440 Lawrence Bell Drive,

Suite 16, Williamsville

NY, 14221

i3 International Ax401C1M User manual

i3 International Ax401C1M User manual

i3 International Ax401C1M User manual

Related papers

Other documents