Backyard Products 192852 Installation guide

16778

Call Us First!

DO NOT RETURN TO STORE.

For immediate help with assembly or product information

call our toll free number:

1-800-577-9663

or email:

[email protected]

Our staff is ready to provide assistance

April through October M-F 8:00 AM to 6:00 PM EST

Saturday 8:30 AM to 4:30 PM EST

November through March M - F 8:00 AM to 5:00 PM EST

STOP!

(This page intentionally left blank.)

1

BEFORE YOU BEGIN

IMPORTANT!

READ INSTRUCTIONS THOROUGHLY PRIOR TO BEGINNING ASSEMBLY.

- CUSTOMER SERVICE -

Call: 1-800-577-9663 email: customerservice@backyardproductsllc.com

• BUILDING RESTRICTIONS AND APPROVALS

c restrictions and/ or requirements before building.

• ENGINEERED DRAWINGS

Contact our Customer Service Team if engineered drawings are needed to pull local permits.

• SURFACE PREPARATION

To ensure proper assembly you must build your shed on a level surface. Recommended methods and materials to level your shed are

listed on page 8.

• CHECK ALL PARTS

Inventory all parts listed on pages 4 - 6. Contact our Customer Service Team if any parts are missing or damaged.

• ADDITIONAL MATERIALS

You will need additional materials to complete your shed. See page 3 for required and optional materials and quantities.

06/05/13

KEEP THIS MANUAL FOR FUTURE REFERENCE

CLASSIC GENTRY GABLE 12' x 12' (365,8 x 365,8 cm)

ASSEMBLY MANUAL

16778

BUILDING SIZE ACTUAL FLOOR SIZE

12' x 12' (365,8 x 365,8 cm)

A Backyard Products Company

2

TOOLS

Safety! Always use approved safety glasses during assembly.

OptionalRequired

HELPFUL REMINDER SYMBOLS

Look for these symbols for helpful reminders throughout this manual.

ORIENT LUMBER AND TRIM FOR BEST APPEARANCE

= Assistance Required; two or more people.

= Ensure squareness.

= Important required step or operation.

= Helpful assembly hint.

= Mark part with pencil.

= Beginning of steps for assembly or installation.

= You have  nished the assembly or installation.

= Level

❑ Gloves

Framing lumber is graded for structural strength and not appearance. Exterior trim is graded for one good side.

Always install the material leaving the best edge and best surface visible. Please remember that these blemishes in no way

negatively affect the strength or integrity of our product. (See Fig. A, B, C.)

A

❑ Safety Glasses

❑ Tape Measure

❑ Paint Tools

❑ Ladder

❑ Caulk Gun

❑ Hammer

❑ Level

FINISH

BEGIN

❑ Pencil

❑ Phillips

Screwdriver

❑ Drill / Driver

❑ 3/8" Drill Bit

❑ #2 Philips Drive Bit

❑ Tool Belt/

Nail Pouch

❑ Chalk Line

❑ Nail Gun

• gun nails

❑ Tin Snips

(for drip edge)

❑ Square

or

❑ Utility Knife

❑ Shingle Blades

B C

❑ WoodGlue

❑ Sawsall

3

ADDITIONAL MATERIALS

COMPLETING YOUR SHED

You will need these additional materials:

OPTIONAL MATERIALS

REFER TO THE BACK OF THIS MANUAL AND THE MANUFACTURER’S INSTRUCTIONS

FOR INSTALLATION OF SHINGLES, DRIP EDGE AND FELT.

3-TAB SHINGLES (Bundles)...................

PAINT FOR SIDING (Gallons).................

Use 100% acrylic latex exterior paint.

1" GALVANIZED ROOFING NAILS(lbs)...

For shingles.

PAINT FOR TRIM ......................1 Quart

Use 100% acrylic latex exterior paint.

WOOD GLUE ................. Exterior Rated

CAULK ............................................ 3

Tubes

Use acrylic latex exterior caulk that is paintable.

7

2

3

(2) coats recommended.

DRIP EDGE (Feet).................................

#15 ROOFING FELT (Sq ft. to cover).....

1" GALVANIZED ROOFING NAILS(lbs)...

60

180

1/2 lb.

For roo ng felt.

2" (5,1 cm)

x1

1 lb. of 2" (5,1 cm) Hot Dipped

Galvanized Box-Type Nails.

NOTE: Use a minimum of 5/8" (1,6 cm) Oriented Strand Board (OSB)

5/8" x 48" x96"

(1,6 x 121,9 x 243,8 cm)

x3

FLOOR PANELS (Not Included)

You will need  oor panels and nails to complete your  oor.

Floor panel sizes and quantities are shown below.

5/8" x 48" x48"

(1,6 x 121,9 x121,9 cm)

x3

4

2 x 4 x 60-1/2" (5,1 x 10,2 x 153,7 cm)

2 x 4 x 78-1/2" (5,1 x 10,2 x 199,4 cm)

PARTS IDENTIFICATION AND SIZES

Double letter part identi cation

is stamped on some parts.

• Check these locations for part

stamp.

CLASSIC GENTRY GABLE 12' X 12' PARTS LIST

INVENTORY YOUR PARTS before you begin.

We suggest sorting parts by the category they are listed in.

WOOD SIZE CONVERSION CHART

Nominal Board Size Actual Size

1" x 4".................3/4" x 3-1/2" (1,9 x 8,9 cm)

2" x 4"..............1-1/2" x 3-1/2" (3,8 x 8,9 cm)

2" x 3"..............1-1/2" x 2-1/2" (3,8 x 6,3 cm)

1" x 3".................3/4" x 2-1/2" (3,8 x 6,3 cm)

RS

DOOR

RAFTERS

TRIM

WALLS

x5

x1

x24

x1

2 x 4 x 48" (5,1 x 10,2 x 121,9 cm)

AV

AI

2 x 4 x 44-1/2" (5,1 x 10,2 x 113 cm)

x1

x7

x5

2 x 4 x 96" (5,1 x 10,2 x 243,8 cm)

2 x 4 x 92-1/2" (5,1 x 10,2 x 235 cm)

TJ

2 x 4 x 68" (5,1 x 10,2 x 172,7 cm)

x2

2 x 4 x 7" (5,1 x 10,2 x 17,8 cm)

x5

x4

SP

STL

AHR

UM

AL

x6

3/4" (1,9 cm)

GAUGE BLOCK FOR 3/4" (1,9 cm)

MEASUREMENT.

TP

2 x 4 x 67" (5,1 x 10,2 x 170,2 cm)

x2

AM

x1

2 x 4 x 12-1/2" (5,1 x 10,2 x 31,8 cm)

AJ

x14

ADA

x4

2 x 4 x 77-15/16" (5,1 x 10,2 x 198 cm)

AF

2 x 4 x 18-1/8" (5,1 x 10,2 x 46 cm)

x12

6 x 24" OSB (15,2 x 61 cm)

AHL

19/32 x 3 x 62" (1,5 x 7,6 x 157,5 cm)

3/8 x 1-3/4 x 81-1/2" x 3/8" (4,4 x 207 x 1 cm)

3/8 x 1-3/4 x 83-1/2" (4,4 x 212.1 x 1 cm)

x1

x2

ZJ

19/32 x 2-1/2 x 72" (1,5 x 6,4 x 182,9 cm)

19/32 x 2-1/2 x 26 5/8" (1,5 x 6,4 x 67,6 cm)

AH

19/32 x 3 x 62" (1,5 x 7,6 x 157,5 cm)

x2

WYR

WYL

19/32 x 4 x 85-3/16" (1,5 x 10,2 x 216,4 cm)

x2

2 x 6 x 96" (5,1 x 15,2 x 243,8 cm)

2 x 6 x 49-1/2" (5,1 x 15,2 x 125,7 cm)

AS

VX

OVERHANG

x2

2 x 3 x 69" (5,1 x 7,6 x 175,3 cm)

OO

3/8 x 3 x 66" (1 x 7,6 x 167,6 cm)

x1

F

x1

2 x 4 x 34" (5,1 x 10,2 x 86,4 cm)

SG

1" x 3" x 5" (2,5 x 7,6 x 12,7 cm)

x1

GAA

7/16 x 48 x 96" (1,1 x 121,9 x 243,8 cm)

7/16 x 23-1/8 x 96" (1,1 x 58,7 x 243,8 cm)

5

PARTS IDENTIFICATION AND SIZES

ROOF

WINDOW

LOFT/ BENCH/ SHELF

x1

1 x 3 x 96" (2,5 x 7,6 x 243,8 cm)

WJ

x2

1 x 4 x 96" (2,5 x 10,2 x 243,8 cm)

KP

x6

19/32 x 3 x 28-1/8" (1,5 x 7,6 x 71,4 cm)

DT

AZ

x2

19/32 x 3 x 30-1/8" ( 1,5 x 7,6 x 76,5 cm)

2 x 3 x10" (5,1 x 7,6 x 25,4 cm)

x1

7/16 x 36 x 40-7/8"

( 1,1 x 91,4 x 103,8 cm)

AC

x7

PANEL PARTS LIST

NOTE: Panel parts are not stamped with part identi cation.

x1

7/16 x 36 x 96"

(1,1 x 91,4 x 243,8 cm)

1 x 4 x 48" (2,5 x 10,2 x 121,9 cm)

x2

BE

1 x 3 x 48" (2,5 x 7,6 x 121,9 cm)

x2

FO

2 x 3 x 19" (5,1 x 7,6 x 48,3 cm)

x7

LR

x4

2 x 4 x 96" (5,1 x 10,2 x 243,8 cm)

TP

x4

2 x 4 x 48" (5,1 x 10,2 x 121,9 cm)

SP

2 x 3 x 96" (5,1 x 7,6 x 243,8 cm)

x1

PT

2 x 3 x 48" (5,1 x 7,6 x 121,9 cm)

x1

NK

3/8" x 14-1/4 x 22-1/2" (1 x 36,2 x 57,2 cm)

x6

x4

2 x 4 x 22-1/2" (5,1 x 10,2 x 57,2 cm)

AO

x1

2 x 4 x 11-5/8" (5,1 x 10,2 x 29,5 cm)

BG

x1

2 x 4 x 19-3/4" (5,1 x 10,2 x 50,2 cm)

PYA

19/32 x 3 x 8-1/2" (1,5 x 7,6 x 21,6 cm)

DF

x4

19/32 x 3 x 21" (1,5 x 7,6 x 53,3 cm)

BWR

x1

19/32 x 3 x 21" (1,5 x 7,6 x 53,3 cm)

BWL

x1

1/4 x 23-7/8 x 96"

(0,6 x 60,6 x 243,8 cm) Peg board

x1

1/4 x 23-7/8 x 48"

(0,6 x 60,6 x 121,9 cm) Peg board

x1

7/16 x 19-1/2 x 92-1/2"

(1,1 x 49,5 x 235 cm)

x1

7/16 x 19-1/2 x 48"

(1,1 x 49,5 x 121,9 cm)

x1

7/16 x 11-1/2 x 96"

(1,1 x 21,2 x 243,8 cm)

x1

7/16 x 11-1/2 x 48"

(1,1 x 21,3 x 121,9 cm)

x2

7/16 x 48 x 96"

(1,1 x 121,9 x 243,8 cm)

x2

7/16 x 47-7/8 x 48"

(1,1 x 121,6 x121,9 cm)

x2

7/16 x 36-1/2 x 96"

(1,1 x 92,7 x 243,8 cm)

x2

7/16 x 36-1/2 x 47-7/8"

(1,1 x 92,7 x 121,6 cm)

LOFT/ BENCH/ SHELF

1 x 4 x 44-1/2" (2,5 x 10,2 x 113 cm)

x1

HYA

6

WALL PANELS

x9

3/8 x 48 x 84"

(1 x 121,9 x 213,4 cm)

x1

3/8 x 48 x 84"

(1 x 121,9 x 213,4 cm)

x1

3/8 x 48 x 84"

(1 x 121,9 x 213,4 cm)

x2

x1

RIGHT DOOR

x1

LEFT DOOR

x1

3/8 x 48 x 84"

(1 x 121,9 x 213,4 cm)

FASTENER/HARDWARE BAG (Not Actual Size)

3” (7,6 cm)

2” (5,1 cm)

1-1/4” (3,2 cm)

x4 Boxes

x6 Boxes

x91

x19

2” (5,1 cm)

3” (7,6 cm)

1” (2,5 cm)

3/4” (1,9 cm)

x120

x64

x18

x92

2” (5,1 cm)

x2

16" x 8" ( 40,6 x 20,3 cm)

x4

3/4” (1,9 cm)

x12

1/2” (1,3 cm) x12

x12

64” Metal Threshold

3/4” (19 mm) x6

x1

x12

Other HARDWARE (Not Actual Size)

1-1/2” (3,8 cm)

x1

x2

x8

22-1/4" x 29-3/4"

(56,5 x 75,6 cm)

x1

NAIL BOXES (Not Actual Size)

1” (2,5 cm)

7

A

B

C

4"

(10 cm)

3-1/2"

(8,9 cm)

D

CONCRETE FOUNDATION

If you choose to install your kit on a concrete slab refer to the diagram below.

Attach the sill plates on the foundatIon as shown, and continue on to page 11.

AB C DActual Floor SizeBuilding Size

• A treated 2 x 4" (5,1 x 10,2 cm) sill plate is required when installing your shed on concrete.

Purchase full length treated lumber.

• Use a high quality exterior grade caulk beneath all sill plates.

• Fasten 2 x 4" (5,1 x 10,2 cm) sill plates to slab using approved concrete anchors (fasteners not included).

• Check local code for concrete foundation requirements.

144" (365,8 cm)

137" (348 cm)

12'x 12' (365,8 x 365,8 cm)

144" (365,8 cm)

203-5/8" (517,2 cm)

Treated Sill Plate

Caulk between

sill plate and

concrete.

12' x 12' Building Requires:

2 x 4 x 12' (5,1 x 10,2 x 365,8 cm)

x2

Sill plates MUST be treated lumber.

Caulk

x1

Allow new concrete slabs to cure for at least seven (7) days.

12'x 12' (365,8 x 365,8 cm)

2 x 4 x 11'-5" (5,1 x 10,2 x 348 cm)

x2

8

FLOOR LEVELING OPTIONS

There are multiple ways to level your  oor frame. Our recommended leveling method is shown below.

Leveling materials are not included in this kit.

PREFERRED METHOD - 4x4 TREATED RUNNERS

MATERIAL REQUIRED

x3

4" x 4" x 12' (10,2 x 10,2 x 365,8 cm) Treated Lumber

x42

3" (7,6 cm)

Fasteners for Frame to 4"x 4".

(3" Screws shown as one option.)

Minimum 3" screws / exterior grade.

• This shed does not include any  oor or leveling materials.

• See the FLOOR LEVELING section on page 9 for recommended methods and suggested materials to properly level your

 oor, as this will vary depending on your speci c site.

FOUNDATION OR FLOOR MATERIALS

• Level under 4x4 runners only.

• Locate leveling material 12" from ends of runners and no more than 48" apart.

• Asphalt shingles should be used between 4x4 runners and blocks or treated lumber. Never use

shingles in direct contact with ground.

• For best results and aiding in water drainage use gravel under each concrete block.

LEVELING METHODS

Use only wood treated for ground contact and fasteners approved for use with treated wood.

Always support frame seams.

8" Block

4" Block

Gravel

Do not exceed 16".

4x4 Runner

Shingle

Maximum between leveling

material locations.

48"

12"

2x4 Treated Lumber

2" Block

Level

Leveling higher than 16" not recommended.

LEVELING MATERIALS

Gravel

2x4 Treated Lumber

Solid Masonry Blocks in 1", 2", 4" or 8" thickness

Asphalt Shingles

12"

(30,5 cm)

12"

(30,5 cm)

Measurements to

centers of 4x4's.

• 3" Screw angled into 4x4.

• (2) at each point frame and 4x4 touch.

4x4 Runners

(not included).

DOOR

9

FLOOR FRAME

FINISH

5

LEVEL AND SQUARE FLOOR FRAME

Before attaching  oor decking, it is important to level and square the  oor frame.

A level and square  oor frame is required to correctly construct your shed.

BEGIN

2

3

4

1

Use level and check the frame is level before applying  oor panels.

Check for frame squareness by measuring diagonally across corners. If the measurements are the

same, the frame is square. The diagonal measurement will be approximately 203-5/8" (517,2 cm).

When the frame is level and square secure one side of frame to the 4x4 runners using one fastener

at ends of each runner. At the opposite end of the frame, secure the frame to 4x4 runners with one

fastener at ends of each runner making sure the frame remains square (Fig. A).

Once the  oor frame is level and square fasten the frame at each point the frame contacts the 4x4

runners.

See page 8 for the preferred  oor leveling method.

203-5/8"

(517,2 cm)

203-5/8"

(517,2 cm)

First, secure at ends

with one fastener.

Second, secure at ends

with one fastener.

Fig. A

DOOR

10

IMPORTANT!

• The  oor should be used as a level work surface for wall construction.

• Organize your wall sections during subassembly

to avoid over-handling of the walls.

HINT:

IMPORTANT!

SIDEWALL

FRONTWALL

BACKWALL

Check the  oor frame is level after installing  oor panels. Re-level if needed.

DOOR

11

SIDE WALL FRAME

3" (7,6 cm)

PARTS REQUIRED:

x14

x4

DOOR

x64

2 x 4 x 78-1/2" (5,1 x 10,2 x 199,4 cm)

AI

2 x 4 x 96" (5,1 x 10,2 x 243,8 cm)

TP

48"

(121,9 cm)

72"

(182,9 cm)

96"

(243,8 cm)

120"

(304,8 cm)

78-1/2"

(199,4 cm)

24"

(61 cm)

144"

(365,8 cm)

96"

(243,8 cm)

TP

AIx7

SP

TP

SP

48"

(121,9 cm)

96"

(243,8 cm)

2 x 4 x 48" (5,1 x 10,2 x 121,9 cm)

SP

HINT:

1

BEGIN

Orient parts on edge on  oor as shown.

Nail using two 3" nails at each connection.

2

3" (7,6 cm)

Nails

IMPORTANT! You will build two walls the same.

3" (7,6 cm)

Nails

3" (7,6 cm)

Nails

12

2" (5,1 cm)

PARTS REQUIRED:

SIDE WALL PANELS

Flush

DOOR

x100

3/8 x 48 x 84"

(1 x 121,9 x 213,4 cm)

x2

3/4" Gauge

Block

AL

3/4"

(1,9 cm)

Fig. A

3/4"

(1,9 cm)

3/4"

(1,9 cm)

2 Nails

1-1/2"

(3,8 cm)

Overlap

1-1/2"

(3,8 cm)

Overlap

2 Nails

Fig. B

12"

(30,5 cm)

6" (15,2 cm)

3/4" GAUGE

BLOCK

GAA

1-1/2"

(3,8 cm)

48"

(121,9 cm)

Primed side

UP

BEGIN HERE

Place LEFT panel onto wall frame with primed side up as shown.

Locate the panel 1-1/2" above the top plate. Use AL as a gauge block

for the 1-1/2" top overhang measurement. Use GAA as a gauge block to

mark the 3/4" side measurement on the wall stud. Secure panel with two

2" nails in the corners (Fig. A).

3

2

Nail the panel using 2" nails 6" apart on edges and 12" apart

inside panel.

Ensure your wall frame is square by installing one panel and squaring frame.

Move to the opposite end. Using the long edge of the panel as a lever,

move the panel side-to-side until you have a 3/4" measurement on the

wall stud. Secure corner with two 2" nails (Fig. B).

For squareness maintain 3/4" and

1-1/2" measurement along panel edge.

1

BEGIN

AL

1-1/2" GAUGE

BLOCK

Lip

Edge

Square

Edge

13

To draw panels tight

at seams angle nail.

2" (5,1 cm)

PARTS REQUIRED:

x4

SIDE WALL PANELS

x200

Flush

3/4"

(1,9 cm)

3/4"

(1,9 cm)

3/8 x 48 x 84"

(1 x 121,9 x 213,4 cm )

Flush Flush

12"

(30,5 cm)

6" (15,2 cm)

1-1/2"

(3,8 cm)

DOOR

48"

(121,9 cm)

Primed side UP

Place middle panel on frame as shown with primed side facing up

 ush with  rst panel. Nail using 2" nails 6" apart on edges and 12"

apart inside panel.

4

You have  nished building your side wall.

FINISH

6

5

Repeat STEP 4 to secure right panel.

Do not nail

in groove.

Repeat process to make second wall.

48"

(121,9 cm)

AL

1-1/2" GAUGE

BLOCK

AL

Square

Edge

Lip

Edge

Square

Edge

Lip

Edge

14

PARTS REQUIRED:

3" (7,6 cm)

FRONT WALL FRAME (Door Header)

x2

x1

DOOR

x18

F

2 x 4 x 67" (5,1 x 10,2 x 170,2 cm)

AM

1/2”

(1,3 cm)

1/4”

(,6 cm)

1/4”

(,6 cm)

AM

F

AM

F

Glue

1/2”

(1,3 cm)

1/2”

(1,3 cm)

Flush

3" (7,6 cm)

Nails

3/8 x 3 x 66" (1 x 7,6 x 167,6 cm)

HINT:

3" (7,6 cm)

Nails

Apply glue to parts as shown. Align parts on a  at surface as shown.

Turn assembled header over and repeat staggered nail pattern.

Assemble header with 3” (7,6 cm) nails in a staggered pattern.

1

BEGIN

2

3

You have  nished building your door header.

FINISH

4

15

PARTS REQUIRED:

3" (7,6 cm)

FRONT WALL FRAME

DOOR

x30

Orient parts on edge on  oor as shown.

Nail using two 3" nails at each connection and four 3" nails at seam.

2

1

BEGIN

HINT:

137”

(348 cm)

126-3/4”

(321,9 cm)

58-1/4”

(148 cm)

44-1/2”

(113 cm)

36-3/8”

(92,4 cm)

12-3/8”

(31,4 cm)

92-1/2”

(235 cm)

38”

(96,5 cm)

67”

(170,2 cm)

AO

AI x5

STL

69-1/4”

(175,9 cm)

AV

TJ

AJ

12-3/8”

(31,4 cm)

60-1/2”

(153,7 cm)

64”

(162,6 cm)

1-1/2”

(3,8 cm)

1-1/2”

(3,8 cm)

12-1/2”

(31,8 cm)

78-1/2”

(199,4 cm)

(4) 3" (7,6 cm)

Nails

(2) 3" (7,6 cm)

Nails

DIMENSIONS ARE TO CENTER OF STUDS.

MAINTAIN DIMENSION

x2

2 x 4 x 22-1/2" (5,1 x 10.2 x 57,2 cm)

AO

x1

AJ

2 x 4 x 12-1/2" (5,1 x 10,2 x 31,8 cm)

2 x 4 x 60-1/2" (5,1 x 10,2 x 153,7 cm)

x1

AV

x1

2 x 4 x 44-1/2" (5,1 x 10,2 x 113 cm)

STL

2 x 4 x 78-1/2" (5,1 x 10,2 x 199,4 cm)

x5

AI

x1

2 x 4 x 92-1/2" (5,1 x 10,2 x 235 cm)

TJ

(2) 3" (7,6 cm)

Nails

16

PARTS REQUIRED:

3" (7,6 cm)

FRONT WALL FRAME

DOOR

x32

HINT:

DIMENSIONS ARE TO CENTER OF STUDS.

MAINTAIN DIMENSION

68-1/2”

(174 cm)

44-1/2”

(113 cm)

20-1/2”

(52,1) cm

7”

(17,8 cm)

AL x5

67”

(170,2 cm)

SG

BG

11-5/8”

(28,6 cm)

34”

(86,4 cm)

78-1/2”

(199,4 cm)

Header

(2) 3" (7,6 cm)

Nails

Flush

Orient the pre-assembled header, AL, BG and SG as shown.

Secure using 3" nails at each connection as shown.

2

1

BEGIN

2 x 4 x 7" (5,1 x 10,2 x 17,8 cm)

x5

AL

x1

2 x 4 x 11-5/8" (5,1 x 10.2 x 29,5 cm)

BG

x1

2 x 4 x 34" (5,1 x 10.2 x 86,4 cm)

SG

Pre - Assembled Header

Flush

17

PARTS REQUIRED:

3" (7,6 cm)

FRONT WALL FRAME

x1

DOOR

x14

You have  nished your front wall frame.

FINISH

3

Orient parts on edge on  oor as shown.

Secure using 3" nails as shown.

2

1

BEGIN

HINT:

2 x 4 x 68" (5,1 x 10,2 x 172,7 cm)

UM

64"

(162,6 cm)

68"

(172,7 cm)

MAINTAIN DIMENSION

UM

(2) 3" (7,6 cm)

Nails

18

2" (5,1 cm)

PARTS REQUIRED:

FRONT WALL PANELS

DOOR

x50

3/4" Gauge

Block

6" (15,2 cm)

6"

(15,2 cm)

64"

(162,6 cm)

1-1/2"

(3,8 cm)

3/4"

(1,9 cm)

3/4"

(1,9 cm)

3/4"

(1,9 cm)

Primed

side UP

Flush

x1

MAINTAIN DIMENSION

Place the left front wall panel onto wall frame as shown with primed side up.

Use the gauge block to mark the 3/4" measurement on the wall stud. Locate

the panel 1-1/2" from the top plate.

3

2

Proceed to attaching your other front panel.

Nail panels to frame with two 2" nails 6" apart on edges.

1

BEGIN

FINISH

4

Do not nail

in groove.

2 x 4"

3/4" GAUGE

BLOCK

GAA

2x4"

TEMP. SPACER

Square

Edge

Lip

Edge

Page is loading ...

Backyard Products 192852 Installation guide

This manual is also suitable for

Backyard Products 192852 Installation guide

Other documents