Power: Transformers rated at 200 Watts RMS continuous (600 Watts audio) 35Hz-20kHz
Load: Match up to 8 pairs of 4 or 8 Ohm speakers with all on simultaneously.*
Mounting: Mud rings must be used with installation. The out board transformers fit into standard wall Space.
Connections: Wago connectors.
*For amplifiers requiring a load of 8 Ohms or higher you must adjust tap settings to X16 when using more than 4 sets
of 4 or 6 Ohm speakers.
GENERAL INFORMATION
The INW-8 switches up to 8 pairs of 4, 8 Ohm or higher impedance speakers in any
combination, while maintaining a safe load to the amplifier. The load protection is achieved by use of an impedance
matching transformer, which offers several significant advantages. There is little or no heat developed whether one
or all the speakers are operating simultaneously, so no fire hazard exists with the in-wall switcher.
IMPORTANT
The INW-8 is supplied with two impedance matching jumpers that are normally connected to the X8 position,
which multiplies the speaker impedance to 8 times the nominal value. Thus if 8 pairs of 4 Ohm speakers are
switched on at the same time, the parallel impedance load would be .50 Ohms. The transformer setting multiplies
the impedance by 8, so the total load to the amplifier appears as 4 Ohms. The jumper settings can be adjusted to
accommodate different situations.
INW-8
Insert a screwdriver into the Wago connector with a rocking motion to the stop. The screwdriver is captivated,
holding the cage-clamp open, while the wire is inserted. The screwdriver is withdrawn and the wire is
automatically clamped.
Your AUDIOPLEX TECHNOLOGY INW-8 Series Speaker Selector is covered by a Lifetime
warranty against any defects in workmanship and materials. Any defects will be remedied without
charge for labor or parts.
Damage incurred by shipping or accident is not considered to be a defect, and not covered by this
warranty. AUDIOPLEX TECHNOLOGY, is not responsible for defective operation caused by abuse or
by modification or service by any unauthorized person or agency.
The unit must be properly installed and operated according to instructions for the warranty to apply.
Any necessary servicing must be done by AUDIOPLEX TECHNOLOGY. The unit must be returned
expenses prepaid, with written authorization from the company. The product must be shipped with the
proof of purchase and in the original carton and packing material to avoid damage. This warranty gives
you specific legal rights. You may have other rights which vary from state to state.
TECHNOLOGY
INSTALLATION MANUAL
2000 - 6/22/00
IN-WALL STEREO SWITCHER
WIRING
WARRANTY
INW-8
(front view)
1 5
4 8
2 6
3 7
- R + - R +
- R + - R +- R + - R +
- R + - R +
+ L - + L -
5 RO+
5 RO-
6 RO-
7 RO-
8 RO-
6 RO+
7 RO+
8 RO+
1 RO+
1 RO-
2 RO-
3 RO-
4 RO-
2 RO+
3 RO+
4 RO+
5 LO+
5 LO-
6 LO+
6 LO-
7 LO+
7 LO-
8 LO+
8 LO-
1 LO+
1 LO-
2 LO+
2 LO-
3 LO+
3 LO-
4 LO+
4 LO-
#6#6 #2#2#5#5 #1#1
#8#8 #4#4#7#7 #3#3
+ L - + L -
+ L - + L -+ L - + L -
TOP
Place transformers
down in the wall
INW-8
(back view)
- R +
+ L -
AMPLIFIER
OUTPUTS
IN L-
IN L+
IN R+
IN R-
AUDIOPLEX TECHNOLOGY
404 GWH, P.O. BOX 440
MELVIN VILLAGE, N.H. 03850
1-800-257-2077 IN N.H. 1-603-544-8601
FAX: 1-603-544-8901
E-MAIL: [email protected]
WIRING DIAGRAM
2000 - 6/22/00
Power: Transformers rated at 200 Watts RMS continuous (600 Watts audio) 35Hz-20kHz
Load: Match up to 12 pairs of 4 or 8 Ohm speakers with all on simultaneously.
Mounting: Mud rings must be used with installation. The out board transformers fit into
standard wall space.
Connections: Wago connectors.
GENERAL INFORMATION
The INW-12 switches up to 12 pairs of 4, 8 Ohm or higher impedance speakers in any
combination, while maintaining a safe load to the amplifier. The load protection is achieved by use of an
impedance matching transformer, which offers several significant advantages. There is little or no heat developed
whether one or all the speakers are operating simultaneously, so no fire hazard exists with the in-wall switcher.
IMPORTANT
The INW-12 is supplied with two impedance matching jumpers that are normally connected to the X16
position, which multiplies the speaker impedance to 16 times the nominal value. Thus if 12 pairs of 4 Ohm
speakers are switched on at the same time, the parallel impedance load would be .33 Ohms. The transformer
setting multiplies the impedance by 16, so the total load to the amplifier appears as 5.3 Ohms. The jumper settings
can be adjusted to accommodate different situations.
INSTALLING THE INW-12
A screwdriver is inserted into the Wago connector with a rocking motion to the stop. The screwdriver is
captivated, holding the cage-clamp open, while the wire is inserted. The screwdriver is withdrawn and the wire is
automatically clamped.
Your AUDIOPLEX TECHNOLOGY INW-12 Series Speaker Selector is covered by a Lifetime
warranty against any defects in workmanship and materials. Any defects will be remedied without
charge for labor or parts.
Damage incurred by shipping or accident is not considered to be a defect, and not covered by this
warranty. AUDIOPLEX TECHNOLOGY, is not responsible for defective operation caused by abuse or
by modification or service by any unauthorized person or agency.
The unit must be properly installed and operated according to instructions for the warranty to apply.
Any necessary servicing must be done by AUDIOPLEX TECHNOLOGY. The unit must be returned
expenses prepaid, with written authorization from the company. The product must be shipped with the
proof of purchase and in the original carton and packing material to avoid damage. This warranty gives
you specific legal rights. You may have other rights which vary from state to state.
TECHNOLOGY
INSTALLATION MANUAL
2000 - 6/22/00
WIRING
WARRANTY
INW-12
(back view)
TOP
WIRING DIAGRAM
9 LO+
9 RO+
9 RO-
10 RO-
11 RO-
12 RO-
10 RO+
11 RO+
12 RO+
9 LO-
10 LO+
10 LO-
11 LO+
11 LO-
12 LO+
12 LO-
- R + - R + - R +
- R + - R + - R +- R + - R + - R +
- R + - R + - R +
+ L - + L - + L -
#5
#10#10 #6 #2#2
#6
#9#9 #5 #1#1
#7#12#12 #8 #4#4#8#11#11 #7 #3#3
+ L - + L - + L -
+ L - + L - + L -+ L - + L - + L -
Place transformers
down in the wall
- R +
+ L -
AMPLIFIER
OUTPUTS
IN L-
IN L+
IN R+
IN R-
INW-12
(front view)
1 5 9
4 8 12
2 6 10
3 7 11
5 RO+
5 RO-
6 RO-
7 RO-
8 RO-
6 RO+
7 RO+
8 RO+
1 RO+
1 RO-
2 RO-
3 RO-
4 RO-
2 RO+
3 RO+
4 RO+
5 LO+
5 LO-
6 LO+
6 LO-
7 LO+
7 LO-
8 LO+
8 LO-
1 LO+
1 LO-
2 LO+
2 LO-
3 LO+
3 LO-
4 LO+
4 LO-
AUDIOPLEX TECHNOLOGY
404 GWH, P.O. BOX 440
MELVIN VILLAGE, N.H. 03850
1-800-257-2077 IN N.H. 1-603-544-8601
FAX: 1-603-544-8901
E-MAIL: [email protected]
2000 - 6/22/00
INWNP-8
SPECIFICATIONS
Power: The INWNP-8 is rated at 100 Watts RMS continuous.
Size: The INWNP-8 will fit most standard double electrical junction
boxes.
Connectors: Screw type connectors.
GENERAL INFORMATION
The INWNP-8 switches up to eight pairs of speakers, in any combination,
from one convenient location. The wiring diagram illustrates connections to the
INWNP-8. Wires should be stripped about 1/4", inserted in the appropriate
connector opening, and the screw tightened. Check to be sure that no stray
strands stick out to cause a short circuit!
WARRANTY
YourAUDIOPLEX TECHNOLOGYâ INWNP-8 speaker selector is covered by
a Lifetime warranty against any defects in workmanship and materials. Any
defects will be remedied without charge for labor or parts.
Damage incurred by shipping or by accident is not considered to be a
defect and not covered by this warranty. AUDIOPLEX TECHNOLOGYâ is not
responsible for defective operation caused by abuse or by modification or service
by any unauthorized person or agency.
The unit must be properly installed and operated according to instructions
for the warranty to apply. Any necessary servicing must be done by AUDIOPLEX
TECHNOLOGYâ. The product must be returned expenses prepaid, with written
authorization from the company. The product must be shipped with proof of
purchase and in the original carton and packing material to avoid damage.
This warranty gives you specific legal rights. You may have other rights
which vary from state to state.
TECHNOLOGY
INSTALLATION MANUAL
2000 - 6/22/00
WIRING DIAGRAM
IN R+
IN R-
IN L+
IN L-
IN R+
IN R-
IN L+
IN L-
5 LO+
5 LO-
6 LO+
6 LO-
7 LO+
7 LO-
8 LO+
8 LO-
5 RO+
5 RO-
6 RO+
6 RO-
7 RO+
7 RO-
8 RO+
8 RO-
1 LO+
1 LO-
2 LO+
2 LO-
3 LO+
3 LO-
4 LO+
4 LO-
1 RO+
1 RO-
2 RO+
2 RO-
3 RO+
3 RO-
4 RO+
4 RO-
AMPLIFIER
OUTPUTS
+ L - - R +
SPEAKER
PAIR 1
SPEAKER
PAIR 2
SPEAKER
PAIR 3
SPEAKER
PAIR 4
SPEAKER
PAIR 5
SPEAKER
PAIR 6
SPEAKER
PAIR 7
SPEAKER
PAIR 8
+ L -
+ L -
+ L -
+ L -
- R +
- R +
- R +
- R +
+ L -
+ L -
+ L -
+ L -
- R +
- R +
- R +
- R +
AUDIOPLEX TECHNOLOGY
404 GWH P.O. BOX 440
MELVIN VILLAGE, N.H. 03850
1-800-257-2077 IN N.H. 1-603-544-8601
FAX: 1-603-544-8901
E-MAIL: [email protected]
INWNP-8
(back view)
INWNP-8
(front view)
2000 - 6/22/00
INWNP-12
SPECIFICATIONS
Power: The INWNP-12 is rated at 100 Watts RMS continuous
Size: The INWNP-12 will fit most standard triple gang electrical
junction boxes.
Connectors: Screw type connectors.
GENERAL INFORMATION
The INWNP-12 switches up to twelve pairs of speakers, in any combination,
from one convenient location. the wiring diagram illustrates connections to the
INWNP-12. Wires should be stripped about 1/4", inserted in the appropriate
connector opening, and the screw tightened. Check to be sure that no stray
strands stick out to cause a short circuit!
WARRANTY
Your AUDIOPLEX TECHNOLOGYâ INWNP-12 speaker selector is covered
by a Lifetime warranty against any defects in workmanship and materials. Any
defects will be remedied without charge for labor or parts.
Damage incurred by shipping or by accident is not considered to be a defect
and not covered by this warranty. AUDIOPLEX TECHNOLOGYâ is not responsible
for defective operation caused by abuse or by modification or service by any
unauthorized person or agency.
The unit must be properly installed and operated according to instructions
for the warranty to apply. Any necessary servicing must be done by AUDIOPLEX
TECHNOLOGYâ. The product must be returned expenses prepaid, with written
authorization from the company. The product must be shipped with a proof of
purchase and in the original carton and packing materials to avoid damage.
This warranty gives you specific legal rights. You may have other rights
which vary from state to state.
TECHNOLOGY
INSTALLATION MANUAL
2000 - 6/22/00
AUDIOPLEX TECHNOLOGY
404 GWH P.O. BOX 440
MELVIN VILLAGE, N.H. 03850
1-800-257-2077 IN N.H. 1-603-544-8601
FAX: 1-603-544-8901
E MAIL: [email protected]
WIRING DIAGRAM
INWNP-12
(back view)
R
R
R
R
L
L
L
LR
R
R
R
L
L
L
L
R
R
R
R
L
L
L
L
1 RO+
1 RO-
2 RO+
2 RO-
3 RO+
3 RO-
4 RO+
4 RO-
1 LO+
1 LO-
2 LO+
2 LO-
3 LO+
3 LO-
4 LO+
4 LO-
5 RO+
5 RO-
6 RO+
6 RO-
7 RO+
7 RO-
8 RO+
8 RO-
5 LO+
5 LO-
6 LO+
6 LO-
7 LO+
7 LO-
8 LO+
8 LO-
9 RO+
9 RO-
10 RO+
10 RO-
11 RO+
11 RO-
12 RO+
12 RO-
9 LO+
9 LO-
10 LO+
10 LO-
11 LO+
11 LO-
12 LO+
12 LO-
IN R+
IN R-
IN L+
IN L-
+ L - - R +
AMPLIFIER
OUTPUTS
- +
- +
- +
- +
- +
- +
- +
- +
+ -
+ -
+ -
+ -
+ -
+ -
+ -
+ -
- +
- +
- +
- +
+ -
+ -
+ -
+ -
INWNP-12
(Front view)
2000 - 6/22/00
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Audioplex AMP 10 Installation guide
-
-
-
-
-
-
-
-
-