Toro Total Control Series Owner's manual

24

User’s Guide

TOTAL CONTROL

TM

24 STATION CONTROLLER

• English

• Español

• Français

i

Thank you for purchasing a Total Control 24-Station controller.

Listed below are some important features you should be aware of

before you begin programming. Details on how to implement these

features are described on the following pages.

• Four fully independent programs that can run concurrently

• Watering day scheduling by Weekdays, Odd/Even days (with

selective day removal) or Day Interval from 1 to 30 days.

• 365-day calendar with automatic compensation for leap year

• Sixteen total start times to use in any program

• Start time stacking overlap protection within each program

• Station watering time from 0 minutes to 10 hours in 1-minute

increments

• Program information erase feature selectable by program

• Non-volatile program memory retains programming information

for up to 30 years without power

• Battery backup maintains time and date during a power failure for

over 2000 continuous hours on a single 9-volt alkaline battery.

• Water budgeting from 0 to 200% in 10% increments

• Rain delay programmable to 7 days

• Self-diagnostic electronic circuit breaker that identifies and over-

rides faulty stations

• Master valve/pump start operation selectable per program

• Complete manual operations available by station and program

• Sensor switch connection for operation with any normally-closed

rain switch device

• Slide switch control provided for rain switch sensor override

• Modular design for ease of programming, installation and service

To take full advantage of all Total Control features, please review the

User’s Guide completely before programming or installing your new

controller.

FEATURES

Features

1

Features....................................................................................................i

Controller Components.....................................................................2–3

General Information..........................................................................4–6

How the Backup System Works.......................................................4

How the Electronic Circuit Breaker Works.....................................5

How the Sensor Feature Works .......................................................6

Programming the Controller...........................................................7–15

Getting Started.............................................................................7–9

Setting the Current Time and Date...............................................10

Erasing Any Prior Programs...........................................................11

Setting the Station Run Time........................................................11

Master Valve/Pump Start On/Off..................................................12

Setting Program Start Times....................................................12–13

Selecting the Days to Water....................................................13–15

Operating the Controller...............................................................15–18

Water Budget..................................................................................15

Manual Operations.........................................................................16

Off and Rain Delay modes.......................................................17–18

Installation Procedures..................................................................19–24

Selecting an Installation Site.........................................................19

Mounting the Controller...............................................................20

Installing Electrical Conduit..........................................................20

Connecting the Valve Wiring........................................................21

Connecting a Pump Start Relay....................................................22

Connecting a Rain Shut-Off Sensor..............................................23

Connecting an Earth Ground........................................................23

Connecting the Power Wires.........................................................24

Troubleshooting..............................................................................25-26

Fuse Replacement................................................................................27

Specifications........................................................................................28

TABLE OF CONTENTS

Table of Contents

2

Controller Components

▲ FIGURE 1

1 LCD Display: For viewing time, program and status information.

2 + /On & – /Off Buttons: For entry of program information.

3 Next Button: For selection of information to be programmed or

reviewed.

4 Function Dial: For selecting the programming and operating

functions.

5 Current Time/Date: For setting the current time and date.

6 Station Times: For setting individual watering time for each station.

7 Program Select Switch: For selection of programs A, B, C or D.

8 Start Times: For setting the time each program cycle will start.

9 Water Days: For setting a watering day schedule for each program.

10. Water Budget: For the increase or decrease of station times for

all stations within a program without changing program memory.

11 Program Erase: For erasing information within a selected program.

12 Manual Program Cycle: For manual operation start of a selected

program watering cycle.

13 Manual Single Station: For timed or untimed operation of a

single station.

14 Rain Off: For immediate shut down of all controller output.

Programmable output delay for 1–7 days (Rain Delay).

15 Run: For automatic operation.

▲ F

IGURE 2

16 Mounting Holes: Pilot screw holes for attaching controller to wall.

17 Safety Fuse: Replaceable 2.0A slow-blow fuse provides

protection from an internal short-circuit condition.

18 Sensor Control Switch: To override rain switch sensor input.

19 Sensor Connection Terminals: For the connection an optional

(normally-closed)rain switch device.

20 Valve Common Terminals: For the connection of up to three

field (24V) common wires.

21 Earth Ground Lug: For connection of a 16–12 gauge

(1.0–2.0mm

2

) copper ground wire to an earth ground.

22 1/2" NPT Conduit Nipple: For the connection of an electrical

conduit access body for input power wiring.

23 Valve Wire Terminals: For the connection of valve control wires.

24 Master Valve Terminal: For the connection of a master valve or

pump start relay control wire.

25 Battery Compartment: 9-volt alkaline battery access compartment.

CONTROLLER COMPONENTS

Page is loading ...

4

This section contains general information on:

• How the backup system works

• How the electronic circuit breaker works

• How the sensor feature works

HOW THE BACKUP SYSTEM WORKS

The Total Control uses non-volatile memory to store watering

programs. This type of memory prevents the watering program

information from becoming lost in the event of a power failure. An

additional benefit of non-volatile memory is that a factory-installed

backup program is not necessary, thereby avoiding the potential for

unplanned operation.

Because the current time and date are always changing, only the most

recent date can be saved in non-volatile memory. Therefore, a battery

is required to maintain the correct time and date in the event of a

power failure. A 9-volt alkaline battery (not provided) will maintain

the correct time and date during power failures up to 90 days. In a

typical installation, the battery should last from two to four years

before replacement is necessary. Once the battery or AC power is

connected, the controller can be fully programmed for operation.

Note: For operation of the valves, AC power must be applied.

To install the battery:

1. Unlatch the hinged control module

assembly and carefully swing it

outward to open.

2. Locate and remove the battery

compartment cover from the lower

back side of the module. See Figure 3.

3. Connect a 9-volt alkaline battery to

the battery clip terminals.

4. Insert the battery into the

compartment and reinstall the battery compartment cover.

Caution: Batteries contain hazardous material. Always handle and

discard batteries properly in accordance with the battery

manufacturer’s recommendations.

GENERAL INFORMATION

General Information

Figure 3

9-Volt Alkaline

Battery

5

General Information

HOW THE ELECTRONIC CIRCUIT

BREAKER WORKS

The controller is equipped with an electronic circuit breaker. If the

controller detects a short circuit, the affected station(s) will be turned

off automatically. The display will then flash “

SHORT” and the shorted

station number or “

MASTER VALVE.” The controller continues to

automatically water the other stations and the following watering

programs until the shorted station is repaired. The program will be

cancelled if the master valve circuit is shorted. Each automatic start

will attempt another cycle and retest the short-circuited valve.

Listed below are the most common conditions which will activate the

electronic circuit breaker. After correcting the problem, return the

controller to normal operation as follows:

1. Set the dial to one of the following positions:

Run,

Manual-Single Station

or

Manual-Program Cycle

.

2. Press the

OFF

button to return the controller to the normal

operating mode.

Condition: The word “SHORT” displays with one or more station

numbers.

Diagnosis: One or more stations are shorted.

Solution: Check the wiring of the displayed stations for the cause

of the shorted condition. Repair valve(s) and/or wiring

as needed.

Diagnosis: Too many valves operating at the same time causing an

overload condition.

Solution: Check watering programs for concurrent station

operation. Include master valve/pump start relay if used.

Maximum total output is 24 V a.c. at 1.25 amps. Reduce

the number of stations running at the same time.

Condition: The word “SHORT” displays without any station

numbers.

Diagnosis: A short circuit has occurred with a time duration too

short for the controller to determine the station.

Solution: Check all valve wiring for breaks in the insulation

which may cause a station output to short to common.

Diagnosis: A transient power surge spike has occurred.

Solution: Reset the controller.

Diagnosis: A short or overload occurred on one watering cycle but

was no longer there on a subsequent cycle.

Solution: Check for loose and/or exposed valve wiring.

6

HOW THE SENSOR FEATURE WORKS

The Total Control is equipped to operate with an optional rain

sensing device (rain switch) to prevent automatic controller operation

during rain.

The rain switch is a simple device, typically installed on a roof

overhang or stationary structure exposed to rainfall and full sun, and

shielded from irrigation spray.

When rain occurs, the normally-closed rain switch senses the moisture

and opens the valve common circuit, effectively preventing all output

to the field. The electronic programming portion of the controller is

isolated from the rain sensor switch, and continues to operate as

programmed. When rain stops and the rain switch returns to its

normally-closed state, the valve common circuit is restored, enabling

watering to resume as scheduled.

A two-position sensor switch (see item 18 on page 3) is provided to

enable you to easily bypass operation of the the rain switch at any

time. If you choose to disregard rain switch input, place the

SENSOR

switch in the

Bypass

position. To enable rain switch operation, place

the Sensor switch in the

Active

position.

General Information

IMPORTANT: If a rain switch is NOT connected to the

controller, the

SENSOR

switch MUST be in the

BYPASS

position to enable controller operation.

The controller will not operate automatically or manually if the

SENSOR

switch is in the

ACTIVE

position without a rain switch

connected.

7

This section covers the following topics:

•

Getting started

• Setting the current time and date

• Erasing any prior programs

• Setting the station run time

• Selecting Master Valve/Pump Start on/off

• Setting the program start times

• Selecting the days to water

GETTING STARTED

PREPROGRAMMING THE CONTROLLER

The unique design of the Total Control enables you to easily remove the

control module from the cabinet for convenient programming while in the

comfort of your home.

To take advantage of this feature, unlatch the control module and swing it

outward. Disconnect the ribbon cable, then simply unclip the module from

its support frame. Now, by installing a 9-volt alkaline battery (as shown on

page 4), you can program and review your watering schedules and have the

controller ready to operate immediately upon completion of the

installation procedures.

Note: To extend battery life, the display will automatically dim after two

minutes of inactivity. To restore the display, simply turn the function dial

to any position. A fresh battery will maintain the current time and date for

over 2000 hours of continuous duty. The program memory is non-volatile

and does not require a sustaining power source for retention.

WHAT IS A WATERING PROGRAM?

A watering program is basically a small set of instructions which tells the

control module when to start a watering cycle, which stations to operate

during the cycle, which days the cycle will be active and how long each

station will operate during the cycle. The Total Control has four

independent watering programs available for your use. Although only one

program is required to operate your controller, using separate programs

enables you to optimize the amount of water being applied to different

areas of the landscape. For example, you might use one program to water

lawns in full sun every day. Another program could be used to water lawns

in partial shade only on Monday, Wednesday and Friday. Trees and shrubs

PROGRAMMING THE

CONTROLLER

Programming the Controller

8

using drip irrigation could run on a separate program once every two weeks.

The garden area requirements might include watering every other day.

To take full advantage of the programming options available, it is

important to first understand how the controller works during operation.

The following section explains what a watering cycle is and provides a

basic example of how multiple programs can be set up.

WHAT IS A PROGRAM WATERING CYCLE?

When a watering start time is selected, that time becomes the beginning

of an automatic watering cycle. A watering cycle operates each station

assigned to the program, one by one, in numerical order.

In the following example (also shown on the sample watering plan on

page 9), we have set up Program A to start at 2: 00 a.m. and again at

3:00 a.m. on a 1-day interval (every day). Stations 1, 2, 4 and 5 are front

and back yard lawn areas which get full sun throughout the day. Each

station will run for 10 minutes per watering cycle, for a total of 20

minutes run time per day. Stations 3, 6 and 7 are lawn areas which are

shaded during the afternoon hours. These areas require less water, so we

have assigned them to Program B and programmed them to run once for

20 minutes on a 2-day interval (every other day).

At 2:00 a.m., Program A watering cycle starts. Station 1 turns on, runs for

10 minutes, and shuts off. Station 2 turns on, runs for 10 minutes, and

turns off. Stations 4 and 5 operate sequentially in the same manner, each

running for their set run time. When Station 5 shuts off, the watering

cycle is completed for the first start time. At 3:00 a.m., the watering cycle

starts again and repeats the same station-by-station watering sequence.

Note that we have 40 minutes total operating time per cycle in

Program A. If we had set the next start time at 2:30 a.m., the start time

would have been delayed until 2:40 a.m., enabling the first cycle to finish

as programmed. This function is called “start time stacking”, and can

occur within each program.

Watering programs, however, operate independently, which means that

two or more programs can run simultaneously. In our example,

Program B will also start at 2:00 a.m. Therefore, Stations 1 and 3 will

turn on at the same time, and Station 2 will turn on while Station 3 is

running. This feature enables more watering to be completed within the

prime “watering window”, which is generally between Midnight and

6:00 a.m.

Note: When scheduling watering programs to run simultaneously, it is

important to ensure the water supply has sufficient pressure and volume

to maintain optimum sprinkler performance.

Programming the Controller

WATERING SCHEDULE FORM (SAMPLE)

For your convenience, a Watering Schedule Form/Quick Reference Card

is provided. Use the form to plan and record your automatic watering

activities. Use the quick reference instructions when minor programming

changes are required. Keep the card with the controller by attaching it to

the inside front cover.

9

Programming the Controller

Station

Watering Day Schedule

Station Description

Week Days

Odd/Even

Interval

1

Watering Cycle Start Times

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

21

22

20

24

23

Program A Program B Program C Program D

Watering Schedule Form

Station Run Time

FFrroonntt LLaawwnn ((ssuunn)) 1100 mmiinn

SSiiddee LLaawwnn ((sshhaaddee)) 2200 mmiinn

BBaacckk LLaawwnn ((ssuunn)) 1100 mmiinn

BBaacckk LLaawwnn ((sshhaaddee)) 2200 mmiinn

11

22

22 aamm,, 33 aamm

22 aamm

(Example)

10

SETTING THE CURRENT TIME AND DATE

Before you can program the controller for automatic watering, you must

set the controller clock to the current time and date. This controller

features a 365-day calendar with automatic

leap year compensation. Once

the date is set, the controller keeps track of the

date and enables trouble-

free, odd-even day of the month watering required in some locations.

The time and date apply to all programs. To set the time and date, follow

the steps below.

1. Turn the Function Dial to the

Current Time & Date

position. The

Hour digits and

AM

/

PM

will flash.

2. Press the + button to increase or – button to decrease the hour

digit.

Note: Continuous pressure on the + or – buttons, causes the

display to change rapidly.

3. Press the

Use the + and/or – buttons to set the current minute.

4. Press the

Use the + and/or – buttons to set the current year.

5. Press the

Use the + and/or – buttons to set the current month.

6. Press the

Use the + and/or – buttons to set the current calendar day.

7. Return the Function Dial to the

Run

position when the current

time and date have been set.

Programming the Controller

11

ERASING ANY PRIOR PROGRAMS

This process enables you to easily clear the controller memory of all

user-defined watering program information within an individual

program. This is an optional procedure and can be skipped if you wish

to retain previous program operating information or the controller has

not yet been programmed.

Erasing a program resets the memory to factory conditions: No station

run time, program start time or active watering days. Water Budget is

set to 100% and Master Valve/Pump Start is set to be “On.”

Note: This process is program independent and resets only the

information for the selected program.

To erase program information for a selected program:

1. Select Program

A

,

B

,

C

or

D

with the Program switch.

2. Turn the function dial to the

Program Erase

position. The display

will show “

ERASE.”

3. Press and hold the

OFF

button until “DONE” is displayed.

4. Repeat this procedure for each program you wish to erase.

SETTING THE STATION RUN TIME

A station is assigned to a program when it is given a station run time

(from 1 minute to 10 hours) in that program. The station can have only

one run time per program. Additionally, the station can be assigned to

any number of programs and have a different run time assigned in each.

To set the run time for each station:

1. Turn the function dial to the

Station Times

position. The

controller displays

STATION NUMBER 1 and OFF (or the current

station run time).

2. Select Program

A

,

B

,

C

or

D

with the Program switch.

3. Press the

(if other than the one displayed).

4. Use the + and/or – buttons to display the desired station run time.

Note:

OFF is the factory setting for each station. If the station has a

run time and you wish to remove it from this program, use the +

and/or – buttons to select

OFF, (displayed between 10:00 [ten hours]

and

00:01 [one minute]). (CONTINUED)

Programming the Controller

12

5. Repeat steps 3 and 4 to set a run time for each station you wish to

assign to the selected program.

6. Repeat steps 2 through 5 for each program as necessary.

MASTER VALVE/PUMP START ON/OFF

The Total Control enables automatic operation of the Master

Valve/Pump Start output circuit to be controlled independently for

each watering program. For example, if a program is used for drip

irrigation and the system pump is not required, the Master

Valve/Pump Start output circuit can be shut off whenever that

program begins operation.

The factory setting is

ON for each program. Use the steps below to

select the operation of this feature for each program as necessary.

1. Turn the function dial to the

Station Times

position.

2. Select Program

A

,

B

,

C

or

D

with the

Program

switch.

3. Press the

4. Press the

OFF

or

ON

button to display the operation of the master

valve/pump start output for the selected program.

5. Repeat steps 2 through 4 for each program as necessary.

SETTING PROGRAM START TIME(S)

This procedure is used to set the watering cycle start time(s) for each

program. A maximum of 16 start times can be allocated to the four

programs in any manner. Each start time will initiate a sequential

watering cycle of all stations with an assigned run time in the program.

Note: When16 start times have been allocated, the display will show

NONE REMAINING when attempting to assign additional start times.

To set program cycle start time(s):

1. Turn the function dial to the

Program Start Times

position.

2. Select Program

A

,

B

,

C

or

D

with the

Program

switch.

3. Use the + and/or – buttons to display the start time.

Note: To remove a start time, adjust the time to display

OFF

(located between 11:59 p.m. and 12:00 a.m.).

4. Press the

5. Repeat steps 2 through 4 for each program as necessary.

Programming the Controller

13

Note: The Total Control will operate one watering cycle in a program

at a time. If a start time occurs while a watering cycle is in progress,

the start time will be delayed until the previous cycle is finished (this

is called “start time stacking”). If the watering cycle extends past

midnight into the next day, the cycle will continue operating until

finished. However, if a watering cycle has been delayed until after

midnight into a non-watering day, the watering cycle will not occur.

SELECTING THE DAYS TO WATER

Several watering day scheduling options are available. Each watering

program can utilize any ONE of the following schedules:

• Days of the week

Use this type of schedule to water on specific days of the week. The

days are displayed as three-letter abbreviations. For example, Sunday is

SUN, Monday is MON, etc. Only the days you select to water will

remain on the display.

• Odd Days or Even Days

To select every odd or even number calendar day, use this option.

Because the 31st and the 1st are both odd number days, the 31st is

automatically removed from the schedule. This watering day option

also enables selected days of the week to be removed from the

schedule.

• Day Interval

Selecting watering days by Day Interval enables a specific number of

days between watering to be selected. For example, selecting a 1-day

Interval schedules watering for every day. A 2-day interval schedules

watering for every other day. A 30-day interval is the maximum

interval frequency, which provides watering once every 30 days.

Another setting within the Day Interval is the current day of the

schedule. The current day (displayed as

TODAY) can be set for any day

within the interval. This number automatically increases by one every

day. When the

TODAY number equals the Day Interval number, a

watering day will occur. For example, to water every third day starting

today, a 3-day interval would be set with

TODAY as day 3. Or, to water

every 5 days starting tomorrow, a 5-day interval would be selected with

TODAY as day 4.

Programming the Controller

14

To set a watering day schedule for each program:

1. Turn the function dial to the

Watering Days

position. The display

will show the current watering day schedule for the selected

program.

2. Select Program

A

,

B

,

C

or

D

with the

Program

switch.

3. Set the watering day(s) for the program using one of the three

following procedures: Days of the Week, Odd Days/Even Days or

Day Interval scheduling procedure.

4. Repeat steps 2 and 3 as necessary to set a watering day schedule

for each program.

Days of the Week

A. Press the

shown at the top of the display.

B. Press the

ON

button. SUN (Sunday) will begin flashing.

C. To select the day, press the

ON

button. To remove the day

from the schedule, press the

OFF

button.

D. Press the

E. Repeat steps C and D to set the remaining days of the week.

Odd Days or Even Days

A. Press the

displayed.

B. Press the

ON

button to select the schedule.

Optional: To remove selected days of the week from the

Odd/Even watering schedule:

1. Press the

flashing.

2. Press the

OFF

button to exclude the day from the schedule.

(Press the

ON

button to restore the day to the schedule.)

Day Interval

A. Press the

displayed.

B. Press the

ON

button to select this option.

C. Press the

Interval number (1–30).

Programming the Controller

15

D. Use the + or – button to select the Day Interval (1–30 days).

E. Press the

current setting.

F. Use the + or – button to select the desired setting for today.

This section includes instructions for the following controller operations:

• Water Budget

• Manual Operations

• Off and Rain Delay Modes

WATER BUDGET

The Water Budget feature enables you to easily increase or decrease

the station run time (by percentage) of all

stations assigned to a

selected program. This is handy for making temporary, overall station

run time adjustments without changing the original run time settings.

Water Budget values range from 0 to 200% in 10% increments, with

100% being the normal setting.

For example, as the fall season approaches and the temperature

decreases, you may want to reduce the station time for the stations in

program A by 30%. Later you can return station times to their original

values by setting the Water Budget value back to 100%.

Note: It is possible to inadvertently cause start time stacking when

increasing station run time. Careful planning and use of Water Budget

will prevent this from occurring.

To change the Water Budget percentage value of a selected program:

1. Turn the function dial to the

Water Budget

position.

2. Select Program

A

,

B

,

C

or

D

with the

Program

switch.

3. Use the + and/or – buttons to increase or decrease the percentage

value (0–200%).

4. Turn the function dial to the

Run

position.

Note: The controller displays the % symbol in the

Run

position

when Water Budget is in use for any program. During operation,

the adjusted run time will be displayed.

OPERATING THE CONTROLLER

Operating the Controller

16

MANUAL OPERATIONS

Manual operation allows you to run individual stations or start automatic

watering programs as needed. The Total Control provides separate dial

positions for each type of operation: Single Station and Program Cycle.

SINGLE STATION

This option enables individual stations to be operated for an untimed

duration (turned On/Off) or operated for a selectable duration from

one minute to 10 hours.

1. Turn the function dial to the

Single Station

position.

2. Select Program

A

,

B

,

C

or

D

with the

Program

switch.

Note: The programmed status of the master valve/pump start in

the selected program determines whether the master valve/pump

start will be activated with the manual operation.

3. Use one of the following options to operate the station.

For untimed operation:

A. Press the

wish to operate.

B. Press the

ON

button. The station will turn on and remain on

until one of the following occurs:

•The

OFF

button is pressed

•The controller clock passes midnight

•The function dial is moved to another position

For timed operation:

A. Press the

to operate.

B. Use the + and/or – buttons to set the desired amount of station

run time (for this operation only), from one minute to 10 hours.

C. To select additional stations to operate in sequence, repeat steps

A and B as desired. Each station will operate one-by-one in the

order they were selected.

D. Leave the function dial in the

Single Station

position until the

manual operation is complete, then return the dial to the

Run

position.

Operating the Controller

17

PROGRAM CYCLE

Use this feature to manually operate watering programs. You can run

the entire program or start anywhere within the station sequence of

the program.

Note: Only the stations with an assigned run time in the program will

operate during the program watering cycle.

1. Turn the function dial to the

Program Cycle

position.

2. Select Program

A

,

B

,

C

or

D

with the

Program

switch.

3. Press the

sequence (if other than the station number displayed).

4. Press the

ON

button to start the watering cycle. Watering will start

with the selected station and will be followed by all subsequent

stations. The display will show the run time remaining for the

operating station.

Note: You may advance through the stations by pressing the

the

OFF

button.

5. Leave the function dial in the

Program Cycle

position until the

manual operation is complete, then return the dial to the

Run

position.

OFF AND RAIN DELAY

Use this feature to turn off controller operation for indefinite periods of

time (Off mode) or for a selected number of days (Rain Delay mode).

Turning Off the Controller

Turning the function dial to the

Rain Off

position places the controller

in the Off mode. After a 2-second delay, any current watering activity

will shut off and all subsequent watering program activity will be

suspended. As long as the function dial is in the

Rain Off

position, the

controller will remain in the Off mode. The controller clock continues

to update current time and date, and all watering program information

is retained while in the Off mode. Normal controller operation is

resumed by simply placing the function dial in any other position.

Using the Rain Delay Mode

The Rain Delay mode enables automatic watering to be delayed from

1 to 7 days. At the end of the selected delay period, the controller

resumes automatic operation. (

CONTINUED)

Operating the Controller

18

To set a Rain Delay period

1. Turn the function dial to the

Rain Off

position.

2. Use the + and/or – buttons to select the number of days (1–7) to

delay operation.

3. Turn the function dial to the

Run

position.

The display will show the number of days remaining in the delay

period. The day number will automatically decrease by one digit

each time the clock passes midnight. Automatic operation resumes

when the display shows no delay days remaining.

Note: The controller can be operated manually while in the Rain

Delay mode.

To cancel the Rain Delay mode:

1. Turn the function dial to the

Rain Off

position.

2. Press the – button until the display shows no delay days

remaining.

3. Turn the function dial to the

Run

position.

Operating the Controller

19

Installation Procedures

This section includes instructions for mounting the controller cabinet

and making the necessary wiring connections. To ensure safe

operation, it is important to follow the instructions carefully. The

following procedures include:

• Selecting an Installation Site

• Mounting the Controller

• Installing Conduit

• Connecting the Field Wiring

• Connecting an Optional Rain Switch sensor

• Connecting an Optional Pump Start Relay

• Connecting an Earth Ground

• Connecting the Power Wires

SELECTING AN INSTALLATION SITE

Selecting the proper installation site for the controller is essential to

safe and reliable operation. The Total Control features a weather

resistant cabinet designed for indoor or outdoor installation.

For easy operation and better view of the display, install the controller

so that the display is at, or slightly below, eye level.

The controller should be installed on a vertical wall or other sturdy

structure near a grounded power source. Select a location that shades

the controller during the hottest hours of the day and provides as

much protection from direct sunlight, rain, wind and snow as possible.

DO NOT mount the controller where it will be exposed to direct

spray from the irrigation system.

INSTALLATION PROCEDURES

Page is loading ...

Toro Total Control Series Owner's manual

This manual is also suitable for

Toro Total Control Series Owner's manual

in other languages

Related papers

Other documents