H3C PSR3000-54A User manual

Brand: H3C

Model: PSR3000-54A

Type: User manual

Contents

Overview ·················································· 1

Front panel ···································································· 2

LEDs ············································································ 2

Technical specifications ··················································· 4

Power module configuration ·············································· 4

Installing and removing the power module ······· 6

Installing the power module ··············································· 6

Installing the power module ·········································· 7

Connecting the power cord ··········································· 9

Removing a power module ·············································· 10

Removing the power cord ············································ 11

Removing the power module ········································ 11

Overview

H3C SecPath PSR3000-54A is a AC-input and DC-output power

module. It is hot swappable and provides a maximum output of 3000

The power module supports N+1 or N+N redundancy (see "Power

module configur

ation"). It provides a self-protection mechanism

against input undervoltage, input overvoltage, output overvoltage,

output short circuit, output undercurrent, output overcurrent, and

overtemperature conditions.

IMPORTANT:

The power module shuts down automatically when its

temperature exceeds the acceptable range. When the

temperature returns to the acceptable range, the power

module automatically restarts.

Front panel

Figure 1 Front panel

(1) Power input LED (AC OK) (2) Handle

(3) AC input receptacle (4) Latch

(5) Power output LED (DC OK)

(6) Air vents (airflow from the inside to outside)

LEDs

The power module has two LEDs.

Table 1 LED description

LED Mark Color Description

Power

input LED

AC OK

Off

No power input.

Low power input voltage.

The power module has

entered self-protected state.

Green Normal power input.

Power

output

LED

Green Normal power output.

Red

Abnormal power output

(Output short circuit, output

overcurrent, output

overvoltage, output

undervoltage, or remote

shutdown has occurred. The

power module has entered

self-protected state.)

Orange

An overtemperature

condition has occurred.

NOTE:

fte

the circuit breaker of the power module is switched off, the

LEDs on the power module will remain on for a while.

Technical specifications

Table 2 Technical specifications

Item Specifications

Rated input voltage 100 to 240 VAC @ 50 or 60 Hz

Rated output voltage 240 VDC

Maximum input current 16 A

Maximum output current 55.6 A

Maximum output power

• 1200 W @ 110 VAC

• 2400 W @ 175 to 200 VAC

• 3000 W @ 220 VAC

Dimensions (H × W × D)

41 × 100 × 332 mm (1.61 × 3.94

× 13.07 in)

Ambient

temperature

Operating

temperature

–10°C to +50°C (–14°F to

+122°F)

Storage

temperature

–40°C to + 70°C (–40°F to

+158°F)

Power module configuration

Follow these guidelines to configure power modules for the device:

• Determine the total number of power modules based on the

actual power consumption, the power module slot number, and

power redundancy design.

• Determine the power module redundancy design based on the

power source conditions.

{ When two mains power inputs are provided, you can

configure the power modules in N+N redundancy. N+N must

be not greater than the total number of power module slots.

{ When one mains power input is provided, you can configure

the power modules in N+1 or N+N redundancy. N+1 or N+N

must be not greater than the total number of power module

slots.

• For easy usage and maintenance, configure a circuit breaker for

each power input. The rated current of the circuit breaker must

be a minimum of 20 A.

Installing and removing the power

module

Installing the power module

To avoid bodily injury and device damage, follow the procedures

in Figure 2 to inst

all the power module.

Figure 2 Power module installation procedure

Before the installation, prepare an ESD wrist strap yourself.

Installing the power module

CAUTION:

• To install the power module in a slot to the left of the fan tray

slots, orient the power module with the latch above the

handle.

• To install the power module in a slot to the right of the fan

tray slots, orient the power module with the latch below the

handle.

• To install the power module in a slot above the fan tray

slots, orient the power module with the latch below the

handle.

The following procedure installs the power module in a slot above the

fan tray slots.

To install the power module:

1. Wear an ESD wrist strap, and make sure the strap makes good

skin contact and is correctly grounded.

2. Remove the filler panel from the target slot. As shown in Figure

3, put

your forefinger into the hole of the filler panel and pull the

filler panel out along the guide rails.

Figure 3 Removing the filler panel

3. Unpack the power module.

4. Correctly orient the power module. Holding the power module

handle with one hand and supporting the power module bottom

with the other, slide the power module along the guide rails into

the slot until the latch on the power module clicks into place.

The power module has a disorientation rejection design. If the

power module is oriented incorrectly, you cannot install the

power module into the slot. If you encounter a hard resistance

while inserting the power module, pull out the power module,

reorient it, and then insert it again.

Figure 4 Installing a power module

Connecting the power cord

WARNING!

• Make sure each power cord has a separate circuit breaker.

• Before you connect the power cord, make sure the circuit

breaker for the power cord is turned off.

The PSR3000-54A power module is provided with a 16 A AC power

cord which has a C19 straight entry connector, as shown in Figure 5.

ou can also use a 16 A AC power cord with a C19 angled connector.

To connect the power cord:

1. Plug the AC power cord connector into the AC input receptacle

of the power module.

Figure 5 Connect the power cord

2. Plug the other end of the power cord into an AC power

receptacle, and turn on the circuit breaker.

3. Verify that the power input LED is ON. If the LED is on, the

power cord is correctly connected. If the LED is OFF,

troubleshoot the installation process.

Removing a power module

To avoid device damage and bodily injury, follow the procedures

in Figure 6 to

remove the power module.

Figure 6 Power module removal procedure

Before you remove a power module, prepare an ESD wrist strap

yourself.

Removing the power cord

1. Turn off the circuit breaker of the power cord.

2. Wear an ESD wrist strap, and make sure the strap makes good

skin contact and is correctly grounded.

3. Remove the cable tie, and pull the connector out.

Removing the power module

CAUTION:

Before you insert a removed power module into a power module

slot, make sure the LEDs on the power module are off.

WARNING!

llow the power module to cool before you remove the power

module.

The following procedure removes the power module above the fan

tray slots.

To remove the power module:

1. Pressing the latch in the direction towards the handle, pull the

power module part way out of the slot along the guide rails.

2. As shown in Figure 7, grasping th

e handle of the power module

with one hand and supporting the bottom of the power module

with the other, pull the module slowly along the guide rails out of

the slot.

Figure 7 Removing a power module

3. Place the power module on an antistatic mat.

4. Install the filler panel in the power module slot.

H3C PSR3000-54A User manual

H3C PSR3000-54A User manual

H3C PSR3000-54A User manual

Related papers

Other documents