DAVIS Mounting Pole Kit Installation guide

Brand: DAVIS

Model: Mounting Pole Kit

Category: Routers

Type: Installation guide

This manual is also suitable for

Tripod Kit

Mounting Pole Kit

Installation Manual

This manual covers use of the Mounting Pole Kit with the Integrated Sensor

Suite (ISS) of the Vantage Pro2

system. The kit can also be used with

other Davis Instruments stations, applying the principles shown here with

the ISS.

Components

The mounting kit includes the following:

Tools and Materials Needed

In addition to the hardware shown above, you may need some of the

following tools and materials:

• Adjustable wrench

• Drill with 1/4" (6 mm) bit

Secure the ISS to the Support Tube

The support tube is 19-1/2" (0.5 m) long, and has a swaged end. After you

secure one or both sides of your ISS to the support tube, this end will be

8" Cable Ties

1-1/2" Saddles

1-1/2" Saddle

5/16" Flat Washers

Extension Tube (21" long)

Support Tube

(19.5" long, swaged end)

5/16" x 1-1/2"

U-Bolt

5/16" Lock Washers

5/16" Hex Nuts

5/16" x 3"

Lag Screws

Mount the Extension Tube

inserted into the top of the extension tube. Make sure the swaged end of the

support tube is pointing downward as you secure the ISS (or other station).

The ISS comes with U-bolts, washers, and hex nuts for the purpose of

mounting it on a pole. Consult your ISS Installation Manual for detailed

instructions.

Note: Remember, when mounting both sides together, that whichever side of the

ISS is mounted first, the U-bolt from the opposite side ALSO must be

placed around the pole before you tighten anything. (If it is not, there is no

way to slide it in later.)

If you wish to put the anemometer higher than the rain collector side of your

ISS on the support tube, follow the instructions in the ISS Installation Manual

for mounting each side separately.

The anemometer arm must point northward or you will have to re-orient the

wind vane after mounting. (As shown in Appendix C in the ISS manual.)

Mount the Extension Tube

The extension tube is 21" long (and does not have a swaged end.)

1. In a fence-post or other flat vertical surface, drill two holes, using one of the

1-1/8" saddles as a guide.

2. Drill another set of holes at least 12" (0.3 m) away from the first holes.

3. Using the 5/16" flat washers and lag screws, secure the saddles against the

extension tube and into the post.

1/4" Hex Nut

1/4" Lock Washer

Nut Plate

U-Bolts

Rain Collector

Mounting Base

1/4" Flat Washer

1/4" Lock Washer

1/4" Hex Nut

Anemometer

Mounting Base

Install the Support Tube on the Extension Tube

4. Tighten the lag screws until the tube will not slide up or down no matter

how hard you try to move it.

Install the Support Tube on the Extension Tube

1. Insert the swaged end of the support tube in the open top of the extension

tube.

2. Place the U-bolt provided in the mounting pole kit around the tubes where

they overlap. Secure with flat washers, lock washers, and hex nuts as shown

in the illustration.

3. Tighten the hex nuts quite firmly, until the U-bolt begins to dent the tubing

slightly. We recommend the use of a torque wrench with 25 lb-ft of pressure

to fasten the hex nuts.

Support Tube

(swaged end)

Extension Tube

(21" long, no swaged end)

Saddle

Flat Washers

Lag Screws

12"

minimum

Product Number: #7717

Davis Instruments Part Number: 7395.298

Rain Collector Heater Installation Manual

Rev. C (12/10/08)

This product complies with the essential protection requirements of the EC EMC Directive 2004/108/EC.

3465 Diablo Avenue, Hayward, CA 94545-2778 U.S.A.

510-732-9229 • Fax: 510-732-9188

E-mail: [email protected] • www.davisnet.com

The tube should be fastened as firmly as possible so that the tube and

station won’t wobble or tilt, causing the station to create and log erroneous

data.

Note: Do not use over 25 lb-ft torque wrench, it may damage the U-bolts.

4. Use the 8" cable ties to secure cable as needed.

Long Extension Tube

(secure in the tripod)

5/16"

Heavy

Duty

Hex Nuts

5/16" Lock

Washers

5/16" Flat

Washers

Saddle

Tighten until

5/16" x 1-1/2" U-bolt

dents the tubing slightly

1 1/4"

Anemometer Extension Tube

(swaged end pointing

downward)

ISS

DAVIS Mounting Pole Kit Installation guide

Brand: DAVIS

Model: Mounting Pole Kit

Category: Routers

Type: Installation guide

This manual is also suitable for

Tripod Kit

Download PDF

report

DAVIS Mounting Pole Kit Installation guide

This manual is also suitable for

DAVIS Mounting Pole Kit Installation guide

Related papers

Other documents