Philips BDL3210Q User manual

Brand: Philips

Model: BDL3210Q

Category: Public displays

Type: User manual

This manual is also suitable for

www.philips.com/welcome

BDL3210Q

BDL4210Q

BDL4610Q

User Manual (English)

BDL3210Q / BDL4210Q / BDL4610Q

Safety Instructions

Warnings and Precautions

KNOW THESE SAFETY SYMBOLS

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol indicates high voltage is present inside. It is dangerous to make any kind of contact with any inside part of this product.

This symbol alerts you that important literature concerning operation and maintenance has been included with this product.

Note to CATV system installers: This reminder is provided to call CATV system installer’s attention to Article 820-40 of the National Electrical Code

(Section 54 of Canadian Electrical Code, Part I), that provides guidelines for proper grounding and, in particular, species that the cable ground shall be

connected to the grounding system of the building as close to the point of cable entry as practical.

CAUTION: FCC/CSA regulations state that any unauthorized changes or modications to this equipment may void the user’s authority to operate it.

CAUTION: To prevent electric shock, match the wide blade of plug to the wide slot, and fully insert the plug.

IMPORTANT: One Federal Court has held that unauthorized recording of copyrighted TV programs is an infringement of U.S. copyright laws. Certain

Canadian programs may also be copyrighted and any unauthorized recording in whole or in part may be in violation of these rights.

TO PREVENT DAMAGE WHICH MAY RESULT IN FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR

MOISTURE.

The Socket-outlet should be installed near the apparatus and be easily accessible.

Read and follow these instructions when connecting and using your Public Information Display:

• Unplug the display if you are not going to use it for an extensive period of time.

• Unplug the display if you need to clean it with a slightly damp cloth. The screen many be wiped with a dry cloth when the power is

off. However, never use alcohol, solvents or ammonia-based liquids.

• Consult a service technician if the display does not operate normally when you have followed the instructions in this manual.

• The casing cover should be opened only by qualied service personnel.

• Keep the display out of direct sunlight and away from stoves or any other heat sources.

• Remove any object that could fall into the vents or prevent proper cooling of the display’s electronics.

• Do not block the ventilation holes on the cabinet.

• Keep the display dry. To avoid electric shock, do not expose it to rain or excessive moisture.

• If turning off the display by detaching the power cable, wait for 6 seconds before re-attaching the power cable for normal operation.

• To avoid the risk of shock or permanent damage to the set do not expose the display to rain or excessive moisture.

• When positioning the display, make sure the power plug and outlet are easily accessible.

• IMPORTANT: Always activate a screen saver program during your application. If a still image in high contrast remains on the

screen for an extended period of time, it may leave an ‘after-image’ or ‘ghost image’ on the front of the screen. This is a well-known

phenomenon that is caused by the shortcomings inherent in LCD technology. In most cases the afterimage will disappear gradually

over a period of time after the power has been switched off. Be aware that the after-image symptom cannot be repaired and is not

covered under warranty.

BDL3210Q / BDL4210Q / BDL4610Q

iii

Regulatory Information

CE Declaration of Conformity

We declare under our responsibility that the product is in conformity with the following standards:

• EN60950-1:2006+A11:2009 (Safety requirement of Information Technology Equipment)

• EN55022:2006+A1:2007 (Radio Disturbance requirement of Information Technology Equipment)

• EN55024:1998+A1:2001+A2:2003 (Immunity requirement of Information Technology Equipment)

• EN61000-3-2:2006 (Limits for Harmonic Current Emission)

• EN61000-3-3:2008 (Limitation of Voltage Fluctuation and Flicker) following provisions of directives applicable

• 2006/95/EC (Low Voltage Directive)

• 2004/108/EC (EMC Directive)

• 2005/32/EC (EuP, Energy-using Product Directive) EC No. 642/2009 Implementing

• 93/68/EEC (Amendment of EMC and Low Voltage Directive) and is produced by a manufacturing organization on ISO9000 level.

Federal Communications Commission (FCC) Notice (U.S. Only)

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in

a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions manual, may cause harmful interference to radio communications. Operation of this equipment in

a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own

expense.

Changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to operate the

equipment.

Use only an RF shielded cable that was supplied with the display when connecting this display to a computer device.

To prevent damage which may result in re or shock hazard, do not expose this appliance to rain or excessive moisture.

THIS CLASS B DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN INTERFERENCE- CAUSING EQUIPMENT REGULATIONS.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not

cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired

operation.

BDL3210Q / BDL4210Q / BDL4610Q

Polish Center for Testing and Certication Notice

The equipment should draw power from a socket with an attached protection circuit (a three-prong socket). All equipment that works together (computer,

display, printer, and so on) should have the same power supply source.

The phasing conductor of the room’s electrical installation should have a reserve short-circuit protection device in the form of a fuse with a nominal value

no larger than 16 amperes (A).

To completely switch off the equipment, the power supply cable must be removed from the power supply socket, which should be located near the

equipment and easily accessible.

A protection mark “B” conrms that the equipment is in compliance with the protection usage requirements of standards PN-93/T-42107 and PN-89/

E-06251.

Electric, Magnetic and Electronmagnetic Fields (“EMF”)

1. We manufacture and sell many products targeted at consumers, which, like any electronic apparatus, in general have the ability to emit and receive

electromagnetic signals.

2. One of our leading Business Principles is to take all necessary health and safety measures for our products, to comply with all applicable legal

requirements and to stay well within the EMF standards applicable at the time of producing the products.

3. We are committed to develop, produce and market products that cause no adverse health effects.

4. We conrm that if its products are handled properly for their intended use, they are safe to use according to scientic evidence available today.

5. We play an active role in the development of international EMF and safety standards, enabling us to anticipate further developments in standardization

for early integration in its products.

BDL3210Q / BDL4210Q / BDL4610Q

Information for U.K. only

(A)

(B)

WARNING - THIS APPLIANCE MUST BE EARTHED.

Important:

This apparatus is supplied with an approved moulded 13A plug. To change a fuse in this type of plug

proceed as follows:

1. Remove fuse cover and fuse.

2. Fit new fuse which should be a BS 1362 5A,A.S.T.A. or BSI approved type.

3. Ret the fuse cover.

If the tted plug is not suitable for your socket outlets, it should be cut off and an appropriate 3-pin

plug tted in its place.

If the mains plug contains a fuse, this should have a value of 5A. If a plug without a fuse is used, the fuse

at the distribution board should not be greater than 5A.

NOTE: The severed plug must be destroyed to avoid a possible shock hazard should it be inserted

into a 13A socket elsewhere.

How to connect a plug

The wires in the mains lead are coloured in accordance with the following code:

BLUE - “NEUTRAL” (“N”)

BROWN - “LIVE” (“L”)

GREEN & YELLOW - “EARTH” (“E”)

1. The GREEN & YELLOW wire must be connected to the terminal in the plug which is marked with

the letter “E” or by the Earth symbol or coloured GREEN or GREEN & YELLOW.

2. The BLUE wire must be connected to the terminal which is marked with the letter “N” or coloured

BLACK.

3. The BROWN wire must be connected to the terminal which marked with the letter “L” or

coloured RED.

Before replacing the plug cover, make certain that the cord grip is clamped over the sheath of the lead

- not simply over the three wires.

BDL3210Q / BDL4210Q / BDL4610Q

China RoHS

中国电子信息产品污染控制标识要求 (中国RoHS法规标示要求) 产品中有毒有害物质或元素

的名称及含量

部件名称

有毒有害物质或元素

铅

(Pb)

汞

(Hg)

镉

(Cd)

六价铬

(Cr 6+)

多溴联苯

(PBB)

多溴二苯醚

(PBDE)

外壳 O O O O O O

液晶面板 X X O O O O

电路板组件 X O O O O O

附件

(遥控器，电源线，连接线)

X O O O O O

遥控器电池 X O O O O O

O: 表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T11363-2006 标准规定的限量要求以下.

X: 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T11363-2006 标准规定的限量要求.

環保使用期限

此標識指期限(十年)，電子信息產品中含有的有毒有害物質或元素在正常使用的條件下不會發生外泄或突變

，電子信息產品用戶使用該電子信息產品不會對環境造成嚴重污染或對其人身、財產造成嚴重損害的期限。

BDL3210Q / BDL4210Q / BDL4610Q

vii

North Europe (Nordic Countries) Information

Placering/Ventilation

VARNING:

FÖRSÄKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG ÄR LÄTÅTKOMLIGA, NÄR DU STÄLLER DIN UTRUSTNING PÅPLATS.

Placering/Ventilation

ADVARSEL:

SØRG VED PLACERINGEN FOR, AT NETLEDNINGENS STIK OG STIKKONTAKT ER NEMT TILGÆNGELIGE.

Paikka/Ilmankierto

VAROITUS:

SIJOITA LAITE SITEN, ETTÄ VERKKOJOHTO VOIDAAN TARVITTAESSA HELPOSTI IRROTTAA PISTORASIASTA.

Plassering/Ventilasjon

ADVARSEL:

NÅR DETTE UTSTYRET PLASSERES, MÅ DU PASSE PÅ AT KONTAKTENE FOR STØMTILFØRSEL ER LETTE Å NÅ.

End-of-Life Disposal

Your new Public Information Display contains materials that can be recycled and reused. Specialized companies can recycle your product to increase the

amount of reusable materials and to minimize the amount to be disposed of.

Please nd out about the local regulations on how to dispose of your old display from your local Philips dealer.

(For customers in Canada and U.S.A.)

This product may contain lead and/or mercury. Dispose of in accordance to local-state and federal regulations. For additional information on recycling

contact www.eia.org (Consumer Education Initiative)

Waste Electrical and Electronie Equipment-WEEE

Attention users in European Union private households

This marking on the product or on its packaging illustrates that, under European Directive 2002/96/EG governing used electrical

and electronic appliances, this product may not be disposed of with normal household waste. You are responsible for disposal of this

equipment through a designated waste electrical and electronic equipment collection. To determine the locations for dropping off such

waste electrical and electronic, contact your local government ofce, the waste disposal organization that serves your household or the

store at which you purchased the product.

Attention users in United States:

Like all LCD products, this set contains a lamp with Mercury. Please dispose of according to all Local, State and Federal Laws. For the disposal or recycling

information, contact: www.mygreenelectronics.com or www.eiae.org.

End of Life Directives-Recycling

Your new Public Information Display contains several materials that can be recycled for new users.

Like all LCD produces, this set contains a lamp with Mercury. Please dispose of according to all Local, State, and Federal laws.

As an ENERGY STAR Partner, we have determined that this product meets the ENERGY STAR guidelines for energy efciency.

BDL3210Q / BDL4210Q / BDL4610Q

viii

Table Of Contents

4.2.1. Picture menu ............................................14

5. Input Mode ..............................................................15

6. Pixel Defect Policy .................................................16

6.1. Pixels and Sub-Pixels ............................................16

6.2. Types of Pixel Defects + Dot Denition . 16

6.3. Bright Dot Defects ...............................................16

6.4. Dark Dot Defects .................................................17

6.5. Proximity of Pixel Defects ................................ 17

6.6. Pixel Defect Tolerances ......................................17

6.7. MURA .......................................................................... 17

7. Cleaning and Troubleshooting .............................18

7.1. Cleaning ......................................................................18

7.2. Troubleshooting ......................................................19

8. TechnicalSpecications ........................................20

1. Unpacking and Installation ..................................... 1

1.1. Unpacking .....................................................................1

1.2. Package Contents ..................................................... 1

1.3. Installation Notes ...................................................... 1

1.4. Installing and Removing Table Stands

(optional) .......................................................................2

1.5. Mounting on a Wall ................................................. 3

1.5.1. VESA Grid ....................................................3

2. Parts and Functions ................................................. 4

2.1. Control Panel .............................................................. 4

2.2. Input/Output Terminals .........................................5

2.3. Remote Control ........................................................ 6

2.3.1. General functions .....................................6

2.3.2. Inserting the batteries in the remote

control.............................................................8

2.3.3. Handling the remote control .............8

2.3.4. Operating range of the remote

control.............................................................8

3. Connecting External Equipment .......................... 9

3.1. Connecting External Equipment (DVD/

VCR/VCD) ...................................................................9

3.1.1. Using COMPONENT video input . 9

3.1.2. Using HDMI video input ......................9

3.2. Connecting a PC ....................................................10

3.2.1. Using VGA input .....................................10

3.2.2. Using HDMI input ................................. 10

3.3. Connecting AV Equipment ..............................11

3.3.1. Connecting an external AV

device(AV IN 1) .....................................11

3.3.2. Connecting an external AV

device(AV IN 2) .....................................11

3.4. Connecting USB device ..................................... 12

4. OSD Menu ..............................................................14

4.1. Navigating the OSD Menu ............................. 14

4.1.1. Navigating the OSD menu using the

remote control........................................14

4.1.2. Navigating the OSD menu using the

display’s control buttons ....................14

4.2. OSD Menu Overview ........................................ 14

BDL3210Q / BDL4210Q / BDL4610Q

1. Unpacking and Installation

1.1. Unpacking

• This product is packed in a carton, together with the standard accessories.

• Any other optional accessories will be packed separately.

• Due to the size and weight of this display it is recommended for two people to move it.

• After opening the carton, ensure that the contents are complete and in good condition.

1.2. Package Contents

Please verify that you received the following items with your package content:

1. LCD display

2. Stand

3. Remote control with AAA batteries

4. Power cord (1.5 m)

5. VGA cable (1.5 m)

6. RS232 cable(1.8 m)

7. Quick Start Guide

8. CD ROM

9. Stand cover

AAA

3 4 5

6 7 8 9

LCD Display

LCD-Monitor / Monitor LCD / Moniteur LCD / Monitor LCD /

Monitor LCD / ЖК-монитор / LCD Monitör / LCD 监视器

Installation / Installation / Instalación / Installation / Installazione / Instalacja /

Установка / Kurulum / 安装

Connect / Verbinden / Conexión / Connecter / Collegamento / Połącz /

Подключить / Bağlan / 连接性

www.publicsignagesolutions.philips.com

NOTES:

• For all other regions, apply a power cord that conforms to the AC voltage of the power socket and has been approved by and complies with the

safety regulations of the particular country.

• You might like to save the package box and packing material for shipping the display.

1.3. Installation Notes

• Due to the high power consumption, always use the plug exclusively designed for this product. If an extended line is required, please consult your

service agent.

• The product should be installed on a at surface to avoid tipping. The distance between the back of the product and the wall should be maintained

for proper ventilation. Avoid installing the product in the kitchen, bathroom or any other places with high humidity so as not to shorten the service life

of the electronic components.

• The product can normally operate only under 3000m in altitude. In installations at altitudes above 3000m, some abnormalities may be experienced.

BDL3210Q / BDL4210Q / BDL4610Q

1.4. Installing and Removing Table Stands (optional)

To install table stands:

1. Ensure your display is powered off.

2. Spread a protective sheet on a at surface.

3. Grab and face-down the display and place on the protective sheet..

4. After inserting the stand in the guide block, tighten the screws on both sides of the display.

NOTE: The longer side of the stand should face the front of the display.

To remove table stands:

1. Power off the display.

2. Spread a protective sheet on a at surface.

3. Grab and face-down the display and place on the protective sheet..

4. Remove screws using a screwdriver and place them in a safe place for reuse.

BDL3210Q / BDL4210Q / BDL4610Q

1.5. Mounting on a Wall

To mount this display to a wall, you will have to obtain a standard wall-mounting kit (commercially available). We recommend using a mounting interface

that complies with TUV-GS and/or UL1678 standard in North America.

1. Lay a protective sheet on a table, which was wrapped around the display when it was packaged, beneath the screen surface so as not to scratch the

screen face.

2. Ensure you have all accessories for mounting this display (wall mount, ceiling mount, table stand, etc).

3. Follow the instructions that come with the base mounting kit. Failure to follow correct mounting procedures could result in damage to the equipment

or injury to the user or installer. Product warranty does not cover damage caused by improper installation.

4. For the wall-mounting kit, use mounting screws and tighten them securely. The mounting screw type and length are as below:

BDL3210Q

M4, Length: 12mm~16mm

BDL4210Q

M6, Length: 12mm~14mm

BDL4610Q

M6, Length: 12mm

1.5.1. VESA Grid

BDL3210Q

100(A) x 200(B) mm

BDL4210Q / BDL4610Q

400(A) x 400(B) mm

Caution:

To prevent the display from falling:

• For wall or ceiling installation, we recommend installing the display with metal brackets which are commercially available. For detailed installation

instructions, refer to the guide received with the respective bracket.

• To lessen the probability of injury and damage resulting from fall of the display in case of earthquake or other natural disaster, be sure to consult the

bracket manufacturer for installation location.

Ventilation Requirements for enclosure locating

To allow heat to disperse, leave space between surrounding objects as shown in the

diagram below.

100 mm 100 mm

100 mm

BDL3210Q / BDL4210Q / BDL4610Q

2. Parts and Functions

2.1. Control Panel

INPUT

VOL

POWER button

Use this button to turn the display on or put the display to standby.

button

Use this button to turn on the OSD.

INPUT button

Use this button to change input selection.

[ ] button

Use this button to increase the audio output.

[ ] button

Use this button to decrease to the audio output.

Remote control sensor and power status indicator

• Receives command signals from the remote control.

• Indicates the operating status of the display:

- Lights Blue when the display is turned on

- Lights Red when the display is in standby mode

- Off when the main power of the display is turned off

BDL3210Q / BDL4210Q / BDL4610Q

2.2. Input/Output Terminals

1 2 3 4

5 6 7 8 9 10 11

HDMI

Connects to the HDMI output of an AV device or to the DVI-D

output of a PC. (Using a DVI-HDMI cable/adapter).

VGA In

Connects to the VGA output of a PC or media player.

YPbPr

Component video input (YPbPr) for connecting to the component

output of an AV device.

SPEAKER L/R

Connects to the audio output of a AV device.

PC AUDIO

Connects to the audio output of a computer.

Composite

Connects video & audio of AV device.

AV OUT

Connects to the AV input of another display.

HEADSET

Connects to the headset.

SPDIF OUT

Digital audio output.

USB 2.0

Connects to a USB device.

RS-232

RS-232 network connection input/output for loop through function.

BDL3210Q / BDL4210Q / BDL4610Q

2.3. Remote Control

2.3.1. General functions

TV DVD Blu-ray

IPTV

BACK

INFO

FORMAT

VOL

HDMI1

SMART

SLEEP

OPTION

HDMI2

HDMI3

VGA

USB

AV1

AV2

CVI

SMART

(Standby - power on)

• Switch to standby mode when your display is ON.

• Turn your display off when it is in standby model.

Open or close main menu.

Blu-ray

Key number on your remote controller changes.

IPTV

Key number on your remote controller changes.

DVD

Key number on your remote controller changes.

N/A.

Yellow key

N/A.

Blue key

Sleep clock. Switch your display to standby mode after user-dened

time.

Green key

N/A.

Red key

Demo menu (Digital crystal color, active control).

OPTION

Browse to options relevant with current action or selection.

SLEEP

Set time for display to power down automatically

▲ ▼ ◄ ► Navigation button

• Open the navigation menu in menu mode.

• Press ◄ ► to search forward or backward during AV playback

in USB mode.

• Conrm input or selection in menu mode.

• Play/stop in USB mode.

Fast forward or fast rewind the video or audio le from USB device.

INFO

Browse to options relevant with current action or selection.

N/A.

P +/-

• Scroll to last or next page in menu mode.

• Select last or next le during AV playback in USB mode.

FORMAT

Select screen format.

BACK

• Return to last screen.

Mute or unmute.

N/A.

VOL +/-

Increase and decrease volume respectively.

0-9 numeric buttons

N/A.

SMART

Open on screen menu.

SMART

Open sound menu.

BDL3210Q / BDL4210Q / BDL4610Q

HDMI1

Select the HDMI1 SOURCE.

HDMI2

Select the HDMI2 SOURCE.

HDMI3

N/A.

VGA

Select the VGA SOURCE.

AV1

Select the AV1 SOURCE.

AV2

Select the AV2 SOURCE.

CVI

Select the CVI SOURCE.

USB

Connected USB device can be identied automatically. Select to

browse the contents of the USB device in the main menu. No

hotkey design is required for this on the remote control unit.

BDL3210Q / BDL4210Q / BDL4610Q

2.3.2. Inserting the batteries in the remote control

The remote control is powered by two 1.5V AAA batteries.

To install or replace batteries:

1. Press and then slide the cover to open it.

2. Align the batteries according to the (+) and (–) indications inside the

battery compartment.

3. Replace the cover.

Caution:

The incorrect use of batteries can result in leaks or bursting. Be sure to follow these instructions:

• Place “AAA” batteries matching the (+) and (–) signs on each battery to the (+) and (–) signs of the battery compartment.

• Do not mix battery types.

• Do not combine new batteries with used ones. It causes shorter life or leakage of batteries.

• Remove the dead batteries immediately to prevent liquid from leaking in to the battery compartment. Don’t touch exposed battery acid, as it can

damage your skin.

NOTE: If you do not intend to use the remote control for a long period, remove the batteries.

2.3.3. Handling the remote control

• Do not subject to strong shock.

• Do not allow water or other liquid to splash the remote control. If the remote control gets wet, wipe it dry immediately.

• Avoid exposure to heat and steam.

• Other than to install the batteries, do not open the remote control.

2.3.4. Operating range of the remote control

Point the top of the remote control toward the display’s remote control sensor when

pressing a button.

Use the remote control within 10m/33ft of the display’s sensor, and at a horizontal and

vertical angle of less than 30 degrees.

NOTE: The remote control may not function properly when the remote control

sensor on the display is under direct sunlight or strong illumination, or when

there is an obstacle in the path of signal transmission.

~5m

~30˚

BDL3210Q / BDL4210Q / BDL4610Q

3. Connecting External Equipment

3.1. Connecting External Equipment (DVD/VCR/VCD)

3.1.1. Using COMPONENT video input

DVD / VCR / VCD

[AUDIO IN]

COMPONENT Out

(YPbPr)

Audio Out

[COMPONENT IN]

(YPbPr)

[R]

[L]

3.1.2. Using HDMI video input

DVD / VCR / VCD

HDMI Out

[HDMI IN]

BDL3210Q / BDL4210Q / BDL4610Q

3.2. Connecting a PC

3.2.1. Using VGA input

[VGA IN]

VGA Out

D-Sub 15 pin

[AUDIO IN]

3.2.2. Using HDMI input

HDMI Out

[HDMI IN]

BDL3210Q / BDL4210Q / BDL4610Q

3.3. Connecting AV Equipment

3.3.1. Connecting an external AV device(AV IN 1)

[AV IN]

DVD / VCR / VCD

AV Out

3.3.2. Connecting an external AV device(AV IN 2)

[AV IN]

DVD / VCR / VCD

AV Out

BDL3210Q / BDL4210Q / BDL4610Q

3.4. Connecting USB device

Your display is tted with a USB port that enables you to view photos, or play audio and video les stored on a USB storage device.

USB

Caution:

The manufacturer is not responsible if the USB storage device is not supported, nor for any damage or loss of data caused by connecting your USB

device.

Supported format

PHOTO: JPEG, BMP, PNG, GIF

MUSIC: MP3, WMA, M4A, AAC, AC3

VIDEO: AVI, MP4, MOV, RM/RMVB

5. The folders inside the USB device will be shown on the center of

the screen. Press [►] then [▲] or [▼] to choose the folder you

want to view, then press [OK] to enter.

Photo

Music

Video

Folders

USB operation

1. Power on the display.

2. Connect the USB device to the USB port on the display.

3. Select [Settings] .

Software settingsSettings

Quick picture and

sound setting

Setup

Update software

Watch demo

4. The USB main screen appears.

Photo

Music

Video

Folders

Page is loading ...

Philips BDL3210Q User manual

Brand: Philips

Model: BDL3210Q

Category: Public displays

Type: User manual

This manual is also suitable for

Download PDF

report

Philips BDL3210Q User manual

This manual is also suitable for

Philips BDL3210Q User manual

Related papers

Other documents