Dynex DX-DPF7-10 Installation guide

Brand: Dynex

Model: DX-DPF7-10

Category: Digital photo frames

Type: Installation guide

Quick Setup Guide

DX-DPF7-10 7" Digital Picture Frame

Features

Top view Side views

Package contents

• Digital picture frame

• AC adapter

• Remote control

• User Guide

• Quick Setup Guide

Connecting the AC adapter

1 Complete all other connections.

2 Plug the small AC power connector into the DC 5V jack on the side

of your digital picture frame, then plug the other end into an AC

power outlet.

Installing the remote control battery

NOTE: A battery comes pre-installed in your remote control. To activate the battery, remove the plastic shipping tab

from the battery tray.

WARNING: There is a danger of explosion if the battery is not replaced correctly. Replace with the same or equivalent

type battery.

1 Turn the remote control over to the back side.

2 Push the release tab to the right and pull the battery tray out of the remote control.

3 If this is the rst time you will be using the remote control, remove the plastic shipping tab that covers the battery.

-OR-

If you are replacing the battery, remove the old battery and insert a new lithium coin cell battery (CR2025) into

the battery tray. Make sure that you match the + symbol on the battery with the + symbol on the battery tray.

4 Slide the battery tray back into the remote control until it clicks into place.

Power

Left

arrow 

Exit

Right

arrow 

Rotate

Copy/

Delete

Mode/Enter



USB port

DC 5V jack

Memory card slot

Step 2 Step 3 Step 4

Positioning your digital picture frame

Your digital picture frame has a built-in stand. The stand can be

rotated to support the frame in either a horizontal or a vertical

position. Make sure that the stand is rotated to a position

indicated on the back of the frame in order to ensure stability.

Your frame can also be wall-mounted. Please use the slots on

the back of the frame for either horizontal or vertical mounting.

NOTE: Hardware for mounting your frame is not included.

ENGLISH 09-0443

© 2009 Best Buy Enterprise Services, Inc. All rights reserved. DYNEX is a trademark of Best Buy Enterprise Services, Inc. Registered in some countries. All other products and brand names are trademarks of their respective owners.

Conguring your digital picture frame

1 Press EXIT. The Main menu opens.

2 Press

 or  to highlight the

SETTING icon, then press

MODE/ENTER.

The Setup Menu opens.

3 Press or to highlight an option, then press MODE/ENTER to conrm.

You can select:

• Brightness–Adjust Brightness from -3 to +3.

• Sleep Time–Set your digital picture frame to turn o automatically after a

set period of time.

• Slide Show Time–Adjusts the interval between pictures changing in a

slideshow. Options are 5 Seconds, 10 Seconds, 30 Seconds, 60 Seconds, 60

Minutes, 24 Hours, and O.

• Transition Eect–Select the transition eect to be used during

slideshows. Choices are Random (all transition eects are used), No Eect,

Cover Up, Cover Down, Cover Left, and Cover Right.

• OSD Language–Select the language to be used for the on-screen display.

You can select English, French, or Spanish. The default language is English.

• Photo Mode–Normal/Full Screen. Normal displays pictures in their native

resolution. This may result in black bars being displayed for pictures that are

4:3 format. Full Screen zooms in and crops pictures to ll the entire screen.

• Default–Resets your frame to factory default settings.

• Exit Setup Menu–Close the on-screen menu.

Using your digital picture frame

Starting a picture slideshow:

1 Press the POWER button to turn on

your frame.

2 If no memory card or USB memory

device has been inserted, a slideshow

of pictures contained in the frame's

internal memory will automatically

begin. If a memory card or USB memory device has been inserted, a

slideshow of pictures contained in the inserted media will automatically

begin.

3 Press MODE/ENTER once to enter BROWSE mode and view a single picture.

Press MODE/ENTER again to enter THUMBNAIL mode. Thumbnail-sized

images appear on the screen.

4 Press

, , , or to highlight a thumbnail.

5 Press MODE/ENTER to display the picture.

NOTE: You can rotate pictures clockwise by pressing ROTATE while the picture is on the screen.

Rotated pictures will be stored in their rotated position.

Copying and deleting photos

To copy pictures to your frame:

1 Insert a memory card or USB device. A slideshow of pictures on the inserted

media automatically begins.

2 In SLIDESHOW or BROWSE mode, locate the picture you want to copy, then

press COPY/ DEL. A message asks you if you want to copy the picture.

3 Press  or  to highlight YES, then press MODE/ENTER to conrm.

To delete pictures from internal memory:

1 Remove any card or USB memory device you have inserted in the frame.

2 In SLIDESHOW or BROWSE mode, locate the picture you want to delete, then

press COPY/ DEL. A message asks you if you want to delete the picture.

3 Press

 or  to highlight YES, then press MODE/ENTER to conrm. The

picture will be deleted from the frame‘s memory.

NOTE: The delete function will only delete pictures saved in the frame‘s memory,

not from a memory card.

Troubleshooting

Specications

90-day limited warranty

For complete warranty, visit www.dynexproducts.com.

FCC Part 15

This device complies with Part 15 of the FCC Rules. Operation of this product is subject

to the following two conditions: (1) this device may not cause harmful interference,

and (2) this device must accept any interference received, including interference that

may cause undesired operation.

This equipment has been tested and found to comply within the limits for a class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment o and on,

the user is encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

FCC warning

Changes or modications not expressly approved by the party responsible for

compliance with the FCC Rules could void the user’s authority to operate this

equipment.

Notices

Specications and features are subject to change without notice or obligation.

For service and support call (800) 305-2204.



The frame won’t turn on.

Photo format

Panel size

Memory card formats

Power source

Power consumption

Operating temperature

Weight

Dimensions (W × H × D)

JPEG

7 inch

SD, SDHC, xD, Memory Stick™, and USB ash drives

AC adapter (5V DC)

<5 W

41~95°F (5~35°C)

1.0 lb. (0.45 kg)

8.8 × 6.2 × 1.2 inches (224 × 157 × 30 mm)

The frame turns o by

itself.

Pictures stored in the

frame’s internal memory

cannot be viewed.

Pictures in the frame’s internal memory can only be viewed if no

memory card or USB memory device is inserted. Remove inserted

cards or devices to view pictures in the frame’s internal memory.

Adjust or disable the Sleep Time function in Settings.

A memory card is

inserted in your digital

picture frame but

pictures cannot be

viewed.

The frame displays

some pictures slower

and some pictures

faster.

The remote control does

not work.

Make sure that the AC adapter is inserted properly into the frame and

plugged into the wall outlet.

• Make sure that the memory card is one of the supported formats

and that the les on the card are JPEG picture les.

• Turn your frame o and make sure that the memory card is inserted

all the way into the card slot, then turn the frame on again.

Note: Some digital cameras save pictures in formats other than JPEG. Refer to

your camera’s manual if your pictures are not JPEG les.

Higher resolution pictures load more slowly. Try reducing the size of

your images using photo editing software (not included) or setting

your camera to take pictures at a lower resolution. See your camera’s

operating manual for details on how to reduce the resolution of

pictures taken.

• Make sure the plastic shipping tab has been removed from the

remote’s battery compartment.

• Make sure you are aiming the remote at the sensor located in the

middle of the frame.

• If you are still having problems, replace the battery in the remote.

Dynex DX-DPF7-10 Installation guide

Brand: Dynex

Model: DX-DPF7-10

Category: Digital photo frames

Type: Installation guide

Download PDF

report

Dynex DX-DPF7-10 Installation guide

Dynex DX-DPF7-10 Installation guide

Related papers

Other documents