1155 Southern Road
Morrow, GA 30260
(770) 282 8686
For your safety, be sure to inspect your Washlet S400 occasionally.
● Is the power plug abnormally hot?
● Is the power plug covered with dust?
● Is the outlet loose?
● Is your Washlet operating differently than usual?
* In case anything is abnormal, contact TOTO USA to prevent a fire or an electrical shock.
©2006 TOTO USA, Inc.
0GU9150
2006.7.26
D06991
Instruction Manual
✲ Thank you for your recent purchase of the TOTO
®
Washlet
®
.
✲ Please read the enclosed information to ensure the safe use of
your product.
Important Safety Instructions . . .
Operational Instructions . . . . . . .
Tips for Using the Washlet
®
. . . .
Performance Features . . . . . . . .
Names of Parts . . . . . . . . . . . . .
Before Using the Washlet
®
. . . . .
2
6
7
8
10
12
Introduction
How to use the Washlet
®
. . . . . .
For Best Results . . . . . . . . . . . . .
Adjusting the Temperature . . . . .
Opening and closing the toilet
seat and lid . . . . . . . . . . . . . . . .
Flushing the toilet . . . . . . . . . . . .
To Conserve Energy
Saving power with the timer . . . .
Auto energy saver . . . . . . . . . . .
14
16
16
17
19
21
21
22
Operation
Caring for your Washlet
®
. . . . . . .
Before cleaning the Washlet
®
. . .
Daily care and maintenance . . . .
Thorough cleaning . . . . . . . . . . .
Other care and Maintenance . . . .
Cleaning the power plug . . . . . . .
Cleaning the deodorizing filter . . . .
Cleaning the wand . . . . . . . . . . . .
Cleaning the water supply filter . . .
24
24
25
26
28
28
29
29
30
Maintenance
Prevention of damage from
freezing . . . . . . . . . . . . . . . . . . .
Troubleshooting . . . . . . . . . . . . .
Specifications . . . . . . . . . . . . . . .
32
35
42
Trouble-
shooting
Washlet
®
S400
SW563 (Round Type)
SW564 (Elongated Type)
Limited Warranty . . . . . . . . . . . 43
DISCONTINUED
2 3
Important Safety Instructions
Be sure to read the following safety instructions and use the product only as described in this
manual. Please follow basic safety instructions to ensure the safe use of your product.
READ ALL INSTRUCTIONS BEFORE USING
The following symbols are used to indicate important safety instructions for the use of the product.
The symbol indicates a prohibited use of the product. The
symbol to the left means "Do not disassemble this product".
This symbol is used to indicate a required step in the use of this
product. The symbol to the left means "Always follow this
precaution".
Symbol
Definition
DANGER
Avoid direct contact with
water
Do not wash the main unit or electrical plug with water or detergent.
● Doing so may cause fire or electrical shock.
Do not use this product in
wet or damp places
Do not use this product in wet or damp places, such as a shower or
bathtub area.
● Doing so may cause fire or electrical shock.
Do not disassemble Never disassemble, repair or modify this product.
● Doing so may cause fire or electrical shock.
Do not handle the electrical
plug with wet hands
Do not handle the electrical plug with wet hands.
● Doing so may cause electrical shock.
Discontinue use of a malfunctioning product.
● If the following occurs, disconnect the electrical plug from the wall outlet, and
push the water shutoff button to prevent the flow of water.
● Continued use of a malfunctioning product may result in fire or electrical shock
or cause water damage.
Possible malfunctions:
● Water leaks from either the main
unit or the water pipes.
● The product makes a strange
noise or emits a strange odor.
● The product feels extremely hot.
● The product is cracked or broken.
● The product is smoking.
DANGER
Avoid damaging the electrical cord or toilet seat cord.
● Use of damaged electrical cords may result in a short
circuit, electrical shock or fire.
Do not crack, bend, twist or pull the cords.
Do not treat or heat the cords or place
heavy objects on top of them
Do not use a loose or faulty electrical outlet.
● Doing so may cause fire or electrical shock.
This product should be used with 120V electrical
current only.
● Use of multi-prong outlet adapters with this product
may result in overheating or fire.
Only use tap water or potable water (ground water).
● Use of water that is not safe for drinking may cause irritation or injury to the skin.
Improper use of heated toilet seats can result in a low-grade burn.
● When sitting on the heated toilet seat for extended periods of time, turn the
temperature setting to OFF.
● Make sure that the temperature setting for the heated toilet seat has been set to
the OFF position before being used by the following:
● Young children, the aged or users who cannot perform appropriate
setting of the temperature.
● Sick or disabled users who do not have freedom of movement.
● Users who are on medication that causes drowsiness.
● Users that have consumed a great deal of alcohol or who are
extremely tired and may fall asleep while using the toilet.
Periodically remove dust and dirt from the electrical plug and
make sure it is securely plugged into the wall outlet.
● Failure to do so may result in electrical shock or fire.
● Pull the plug out from the outlet and wipe clean with a dry cloth.
Do not unplug by pulling on cord. To unplug, grasp
the plug, not the cord.
● Pulling on the cord may cause damage and result in
electrical shock or fire.
Removal of the electrical
plug
When removing the main unit for cleaning, be sure to
unplug the electrical cord from the wall outlet to
prevent the risk of electrical shock.
Grounded Outlet Make sure that a proper grounded (3 prong) outlet has been installed.
● Failure to install in a grounded outlet could result in electrical shock in the event
of a malfunction or short circuit.
Do not insert fingers or any other object into the
warm air blower outlet.
● Obstruction of the warm air blower outlet could result
in injury or property damage.
Do not obstruct the outlet with clothing or
your hand
Introduction
DISCONTINUED
4 5
WARNING
Use only a mild dish detergent diluted with water to clean your Washlet. Do not use the
folloing to clean the Washlet.
Toilet bowl cleaner, household cleaner, benzene, paint thinner, powdered cleanser, or nylon
scrubbing pads.
● Use of any cleaning product other than diluted dish detergent may crack the plastic and
cause injury to the user or may damage the hose resulting in water leakage.
Do not stand on or place heavy objects on top of the toilet.
● To avoid injury or damage to the toilet unit, do not stand on or place heavy objects on top
of the toilet.
Do not raise the toilet seat or toilet lid while objects are resting on top of the toilet.
● Lifting the toilet seat/cover with objects resting on them could cause the main unit to
become detached, resulting in injury.
Do not bend or crush the water hose.
● Bending or crushing the water hose may result in water leakage.
When not using the Washlet over an extended period of time, drain the water out of the
hose and pull the electrical plug from the wall outlet.
● Water left standing in the toilet hose over an extended period of time could cause irritation
to the skin.
Refer to Page 32 for instructions on draining the hose.
If water leakage should occur, always close
the water shutoff valve and then turn off the
water.
When installing the water drain valve with water filter, make sure that it is securely
tightened in its proper position.
● Improper tightening of the water valve may result in water leakage.
Preventing damage due to frozen pipes and hoses.
● Frozen water pipes will cause the main unit and the pipes to break, resulting in water
leakage.
● Regulate the room temperature to prevent the pipes and hoses from freezing during cold
months.
Refer to Page 32 for instructions on how to prevent frozen pipes
To prevent sudden water leakage, do not remove the water filter and drain valve when
the water shutoff valve is open.
● Refer to Page 30 for instructions on cleaning the water filter.
● Do not install base plate to Washlet when not attached to the toilet.
Fire or damage may result.
To reduce the risk of burns, electrocution,
fire or injury to persons:
1. Close supervision is necessary when this product is used by, on, or near children or invalids.
2. Use this product only for its intended use as described in this manual. Do not use
attachments not recommended by the manufacturer.
3. Never operate this product if it has a damaged cord or plug, if it is not working properly, if
it has been dropped or damaged, or dropped in water. Return the product to a service
center for examination and repair.
4. Keep cord away from heated surfaces.
5. Never block the air openings of the product or place it on a soft surface, such as a bed or
couch, where the air openings may be blocked. Keep the air openings free of lint, hair,
and the like.
6. Never use while sleepy or drowsy.
7. Never drop or insert any object into any opening or hose.
8. Do not use outdoors or operate where aerosol (spray) products are being used or where
oxygen is being administered.
9. Connect this product to a properly grounded outlet only. See Grounding Instructions.
10. Reservoir should be filled with water only.
WARNING
Save these instructions.
Do not use this product while smoking.
● To avoid the risk of fire, do not smoke while using this product.
To reduce the risk of electrocution:
1. Do not use while bathing.
2. Do not place or store products where it can fall or be pulled into tub or sink.
3. Do not place in or drop into water or other liquid.
4. Do not reach for a product that has fallen into water. Unplug immediately.
DANGER
Grounding Instructions
This product should be grounded. In the event of an electrical short circuit, grounding reduces
the risk of electric shock by providing an escape wire for the electrical current. This product is
equipped with a cord having a grounding wire with a grounding plug. The plug must be plugged
into an outlet that is properly installed and grounded.
DANGER - Improper use of the grounding plug can result in a risk of electric shock.
If repair or replacement of the cord or plug is necessary, do not connect the grounding wire to
either flat blade terminal. The wire insulation having an outer surface that is green with or without
yellow stripes is the grounding wire.
Check with a qualified electrician or serviceman if the grounding wire instructions are not
completely understood, or if in doubt as to whether the product is properly grounded.
This product is factory equipped with a specific electric cord and plug to permit connection to a
proper electric circuit. Make sure that the product is connected to an outlet having the same
configuration as the plug. No adapter should be used with this product. Do not modify the plug
provided - if it will not fit in the outlet, have the proper outlet installed by a qualified electrician. If
the product must be reconnected for use on a different type of electric circuit, the reconnection
should be made by qualified service personnel.
If it is necessary to use an extension cord, use only a three wire extension cord that has a three
blade grounding plug, and a three-slot receptacle that will accept the plug on the product.
Replace or repair a damaged cord.
Introduction
DISCONTINUED
6 7
Operational Instructions
Always follow these precautions to ensure the safe use of your product.
Do not wipe the Washlet, toilet seat
or toilet lid with a dry cloth, toilet
paper or similar substance.
Otherwise scratches could result.
See Page 24 for cleaning methods.
Do not expose to direct sunlight.
Otherwise, yellowing or uneven heating
of the heated toilet seat could result or
the remote control could malfunction.
Avoid getting urine on the Washlet
or wand.
Otherwise, malfunctions could result.
Do not cover the seat sensor, the
person detection sensor or the
remote control receiver window.
Otherwise, the Washlet could
malfunction.
Do not lean back on the toilet lid.
It could scratch the surface.
To avoid electrical damage to your
unit, be sure to unplug the power
cord during lightning storms.
Please use radios and other
appliances away from the Washlet.
Otherwise, interference could result.
Tips for Using the Washlet
®
Protect the environment and reduce the use of water and electricity.
Keeping the lid
closed will
maintain the
warmth of the
toilet seat.
The toilet seat
temperature can be
reduced to save
energy.
Page 16
Reduce the temperature
setting to save energy.
Keep the lid closed to keep the
toilet seat warm and conserve
energy.
Turning the power off
when leaving the house
for a long period of time
will conserve Energy.
See page 13
Turn the power switch to OFF
when the Washlet is not being
used over extended periods of
time.
Once the settings are
configured, the toilet
seat heater will turn off
at that time each day
and save power. You
can set the length of
the power saving
to 3, 6 or 9 hours.
Page 21
Use the timer energy
saver!
Time periods when the
toilet is not used much
are stored and the toilet
seat temperature is
automatically lowered
to save power.
Page 22
Use the Auto energy
saver.
You can use the timer and Auto energy saver together!
Introduction
DISCONTINUED
8
9
Energy-saving features Page
Timer energy saver
Once set, the toilet seat heater will shut off at the same
time every day and save power.
(The power-saving time can be set to 3, 6 or 9 hours.)
21, 22
Auto energy saver
The time when the toilet is not used much is remembered
and the toilet seat temperature is lowered automatically.
Power on/off button
When this button is set to "off," the heated toilet seat and
other features will be turned off allowing even more power
savings.
22, 23
Cleaning features Page
Easy Removal of the
toilet seat and lid
The toilet seat and lid can be removed easily making clean-
up easy.
26, 27
One-touch Washlet
removal
The Washlet can be removed with a single touch.
The toilet can be cleaned all the way to the back, easily.
Wand self-cleaning
Before and after flushing, the wand tip is automatically
cleaned very thoroughly.
—
Full wand cleaning
Each time the wand extends or stores itself, it is cleaned
thoroughly.
—
Wand cleaning button
The wand will extend without spraying any water, so it can
be cleaned very easily.
28
29
Performance Features
Washlet Functions Page
Rear cleansing
The wash alternates between a gentle spray and a forceful
spray 70 times per second for a thorough rear wash while
using less water.
The soft cleansing and front cleansing provide a soft, yet
thorough, whirling flow of water.
14
Wand position
adjustment
The wand's position can be adjusted forward or backward.
Water pressure
adjustment
The water pressure of the spray can be adjusted.
14
Oscillating Wash
The wand moves back and forth, cleaning a wide area
thoroughly.
14
Amenities Page
Heated toilet seat
Warms the toilet seat.
—
Heated dryer
Dries wet areas with warm air.
Temperature
adjustment
The temperatures of the water, toilet seat and dryer can be
adjusted.
16
Deodorizer
Removes odor from the toilet bowl.
16
Remote control
Allows for easy operation while seated.
Seat sensor
The sensor detects when someone sits on the toilet seat
and activates all of the functions.
15
15
11
Soft rear cleansing
Front cleansing
14
Pulsating Wash
A combination of soft/strong water pressure is used to wash.
14
Remote opening/
closing of toilet seat,
toilet lid
The toilet seat and lid can be opened or closed using the
remote control.
17
Automatic opening/
closing
The toilet lid will open and close automatically when it senses
a person.
17, 18
Remote control
flushing
The toilet can be flushed using the remote control.
19
Automatic flushing
The toilet flushes automatically when moving away from the
toilet.
19, 20
13
Introduction
DISCONTINUED
10 11
Names of parts
Remote control
Main unit display
Main unit controls
With the
cover closed
With the
cover open
the buttons have imprints (bumps) for those with impaired vision.
Introduction
DISCONTINUED
12 13
Before Using the Washlet
®
Remote Control Display
Preparation
Putting batteries in the remote control.
➀ Remove the remote control from the hanger.
Holding both side of the remote control, lift it straight
upwards.
➁ Open the battery cover on the back of the remote
control.
➂ Insert two AA batteries.
➃ Close the battery cover.
When the batteries are set correctly in place, the
remote control display module will look like the picture
at right.
In order to keep batteries from splitting or leaking, please be sure to observe the following.
●
Use new batteries of the same type for replacements.
●
Remove the batteries when not using the unit for long periods of time.
●
Do not use rechargeable batteries.
Batteries
Insert the plug into the wall
outlet.
Opening the water shut-off valve
and the junction valve.
Please turn on the junction valve with a
flathead screwdriver.
Check the "Main unit display".
Are the "POWER" LED and the "SEAT" LED
on the main unit display lit?
If the "POWER" LED is not lit, then it
won't be possible to use all of the
functions. Please press the power
on/off button on the main unit control.
(The LEDs will go on.)
1
1
● When replacing the batteries or cleaning the unit, please turn the power on/off button on the
main unit controls to "off." Otherwise, if you mistakenly press a button, the Washlet will flush the
toilet, or open/close the toilet seat or lid.
● When replacing the batteries, the on/off settings for the timer power saver and auto functions
could be lost. (Example: even when the auto toilet flush is set to "off," it is "on.")
Please reconfigure the settings.
2
Check
3
2
The first time that the toilet lid opens after the power cord is plugged in, it will stop if it runs into any
obstacles and the next time that the toilet lid opens, it may stop opening (or close) after opening
part way. (It stores the position from the first time it opens.)
Unplug the power cord when there are no obstacles and then plug it back in and press the [See
source for graphic.] button on the remote control.
Please refer to "Adjusting the temperature" on Page 16 concerning turning the toilet seat "on" or
"off" or adjusting the temperature.
3
Introduction
DISCONTINUED
14 15
How to Use the Washlet
®
1
Please sit squarely on the toilet!
This will provide better cleansing and reduce any splashing.
Standing in front of the toilet
The toilet lid will open automatically.
(Page 17, Auto open/close)
Standard method of use
Drying
Sit on the toilet seat.
The seated sensor will go on and all of the functions will be available.
● In order to prepare to spray warm water, water will be sprayed into the toilet around the wand for
several seconds.
● The Deodorizer will begin.
Wash.
1
For Better Results
Amenity Feature 1 Oscillating
The wand moves back and forth, washing a broad area
thoroughly.
➀
Press the desired button.
➁ Press .
Oscillating function will begin.
➂ Press once more.
Oscillating function will end.
Amenity Feature 2 Pulsating
Alternates hard and soft water pressure.
➀
Press the desired button.
➁ Press .
Pulsating function will begin.
➂ Press once more.
Pulsating function will end.
Standing up from the toilet
After approximately five seconds, the
toilet will automatically flush.
● The deodorizer will end after
approximately one minute.
(Auto toilet flushing Page 19)
Moving away from the toilet
After approximately 90 seconds, the
toilet lid will close automatically.
(Auto open/close Page 18)
Operation
DISCONTINUED
Please adjust the temperature of the spray water and the toilet seat using the and buttons.
To turn the feature off, please press the button repeatedly until the temperature display turns off.
The dryer temperature can be adjusted to one of five levels using the and buttons.
16 17
For Best Results
Adjusting the Temperature
You can adjust the temperature of the spray water, the toilet seat and the dryer with the
remote control. Please set the desired temperature.
1
Open the cover of the
remote control.
2
Adjust the temperature
Opening and closing the toilet seat and lid
Deodorizer
Sitting down on the toilet seat begins deodorizer function.
1
Sit down on the toilet seat.
2
Stand up from the toilet
seat.
The "DEODORIZER" LED on the main unit
display turns on.
Deodorizer begins
The "DEODORIZER" LED on the main unit
display will turn off
After approximately one minute, it
will stop automatically.
There are two ways to open and close the toilet seat and lid: Remote open/close
and Auto open/close.
The toilet seat and lid can be opened and closed using the buttons on the remote control.
Using the remote open/close on the toilet seat and lid
Press on the
remote control
The toilet seat and lid will open or close.
Using auto open/close
When standing in front of the toilet, the toilet lid will open automatically and then the lid and
seat will close automatically after moving away from the toilet.
1
Stand in front of the toilet.
✲ If it does not open, it will open if you move at least
1 ft (30 cm) away from the toilet and then stand in
front of it again.
When it senses somebody, the "SENSOR" LED on
the main unit display will turn on.
When a person is detected with the person detector
sensor, the toilet lid will open automatically.
The toilet lid will open automatically.
1
During power outages or when the batteries wear out, please open and close the toilet seat and lid
by hand.
Initially, the Washlet is set for Auto open/close.
When small children use the Washlet, the sensor may not detect them due to their location in
front of the toilet or their height. In such cases, please open or close the lid or seat with the
remote control buttons.
2
2
1
Operation
DISCONTINUED
18 19
Move at least 1 ft. (30 cm)
from the toilet after using the
toilet.
When sitting on the toilet seat
After approximately 90 seconds, the
toilet lid will close automatically.
● When the sensor no longer detects
anyone, the "SENSOR" LED on the main
unit display will turn off.
Move at least 1 ft. (30 cm)
from the toilet after using the
toilet.
When standing in front of the toilet.
After approximately 90 seconds, the toilet
lid and seat will close automatically.
● When the sensor no longer detects
anyone, the "SENSOR" LED on the main
unit display will turn off.
● Please open the toilet seat using the remote
control.
To turn off the auto open/close
Press the buttons on the
remote control.
Turns off auto open/close
● "OPEN/CLOSE" will disappear from the remote control display .
● Please follow the same procedure to turn it on again.
● The person detection sensor senses when a person is standing in front of
the toilet.
● The person detection sensor emits infrared light as shown in the diagram.
A person will be detected when a he or she approaches in the direction of
this infrared beam.
Person detection sensor
Flushing the toilet
There are two ways to flush the toilet: Remote control flushing and Auto flushing .
The toilet can be flushed using the large flush button on the remote control.
Flushing the toilet using remote control
Press button
on the remote control.
The toilet will flush.
Flushing the toilet using auto flushing
The toilet will flush automatically when you move away from the toilet.
1
The toilet flush switch cannot be used continuously. Please wait approximately ten seconds before
flushing again.
Initially, the Washlet is set for automatic toilet flushing.
When small children are to use the toilet, the sensor may not flush automatically because it
couldn't sense them properly.
The automatic flush will not work for approximately 60 seconds after an automatic flush. Please
use the button on the remote control.
2
1
Stand up after using the toilet.
When sitting on the toilet seat
The toilet will flush automatically
after approximately five seconds.
The automatic flush feature will not work unless
you remain seated for at least six seconds.
2
✲ Depending upon the manner of sitting or posture, the sensor may not detect correctly and cause the toilet to flush
automatically even when someone is still seated on the toilet.
✲ When the auto flush or remote control flush is operating, please do not push the manual toilet flush lever the
opposite direction. It could damage the manual flush lever.
Operation
DISCONTINUED
20 21
After urinating, move at least
1 ft. (30 cm) away from the
toilet.
While standing in front of the toilet
After approximately three seconds, the
toilet will flush automatically.
● When the sensor no longer detects
anyone, the "SENSOR" LED on the main
unit display will turn off.
Someone must stand in front of the toilet for
at least six seconds for the automatic flush
to work.
To turn off the auto toilet flush
Press the buttons on the
remote control
Turns off auto toilet flush
● "FLUSH" will disappear from the remote control display.
● Please follow the same procedure to turn it on again.
✲ When the auto flush or remote control flush is operating, please do not push the toilet manual flush lever the
opposite direction. It could damage the manual flush lever on the toilet.
1
1
When small children use the Washlet, the sensor may not detect them due to their location in
front of the toilet or their height. In such cases, please flush the toilet with the remote control
buttons.
The automatic flush will not work for approximately 60 seconds after an automatic flush. Please
use the button on the remote control.
During power outages or when the batteries wear out, please flush the toilet by hand using the
toilet tank lever.
2
To Conserve Energy
The timer energy saver…
Once the settings are configured, power
saving will take place every day at that time.
During timer power saving, the toilet seat
heater will be off.
The power saving times can be set to 3, 6 or
9 hours.
■ For example, to save power from 1:00 to
7:00 am (six hours).
Saving power with the timer energy saver
Example: When saving power from 1:00 am until 7:00 am (six hours)
1
Press the button on the
remote control at the time
you want to begin saving
energy (1:00 am)
2
Press the button and
set six hours.
The words "TIMER" and "SAVING TIME: 3 hrs."
will be displayed on the remote display module.
Energy saving will begin.
During timer power saving, the "ENERGY SAVER"
LED (green) on the main unit display turns on.
3
Changing the energy saving
period
Press the button.
● Each time the button is pressed, the display will
change from 3 to 6 to 9 to off (no display).
Please select the desired time.
✲ When you want to change the energy saving period (3, 6 or 9 hours), please reconfigure the starting time settings.
4
3
The Washlet can still be used, even while saving power. If someone sits on the toilet seat during
the energy-saving period, the toilet seat heater will turn on temporarily. It takes approximately 15
minutes for the toilet seat to heat up.
When you want to change the power saving start time, please shut off the timer energy saving
feature and press the button once more to set the desired starting time.
4
Operation
DISCONTINUED
22 23
Turning off the Timer energy
saver
Press the button until the
"TIMER" and "SAVING TIME"
display turn off.
The "POWER" and "SEAT" LEDs in the main unit
display will turn on.
Energy saving is turned off.
The auto energy saver…
● The Washlet will store the time periods
when the toilet is used, find low-use
times and automatically lower the toilet
seat temperature to save energy.
■ If there are only two usesper week in the
same time period, energy saving will
begin as a low-use period.
Auto energy saver
Press the button on the
remote control
The word "AUTO" will be displayed in the display
on the remote control.
The temperature of the toilet
seat will be lowered
automatically and energy
saving will begin.
1
It takes two to three days to find the time periods in which the toilet is not used very often. During
that period, power saving will take place gradually.
The Washlet can still be used, even during auto energy saving. If someone sits on the toilet seat
during the energy-save period, the toilet seat heater will turn on temporarily.
2
During the low-use periods, the "ENERGY SAVER"
LED (orange) on the main unit display will turn on.
1. 2
To turn off the auto energy saver.
Press the button.
The word "AUTO" will disappear from the remote display.
Auto energy saver will be turned off.
When using both timer energy saver and auto energy saver
The buttons can be pressed in any order.
Press the button for the time
you want to begin saving energy.
The "POWER" LED in the main unit display will turn on.
See Page 21 for timer energy saver.
Press the button.
See Page 22 for auto energy saver.
For example, energy saving as follows
When not using timer energy saver, the auto energy saver will be operational, saving power.
Operation
DISCONTINUED
24 25
Caring for your Washlet
®
Before cleaning the Washlet
®
Each component can be disassembled for a thorough cleaning.
Caution!
Be sure to turn off the and before cleaning the unit.
Daily care and maintenance
Cleaning the Washlet, toilet seat and lid
Wipe with a soft, damp cloth.
Please dampen a soft cloth with water and wipe these
surfaces after wringing well.
1, 2
When very dirty….
Please wipe down with a soft cloth, using a
diluted kitchen detergent (neutral alkalinity).
Please wipe down with water after that.
If there is toilet cleaner on the Washlet or
seat surface…
Please dampen a soft cloth with water and
wipe up the drops.
2
Please keep the seat sensor, person detection sensor and the remote receiver clean! Many of the functions
will not work if these become dirty. Pages 15, 18 and 35 through 41.
1
The product is made of plastic, so please do not wipe the surfaces with a dry cloth or toilet paper. Doing
so can cause scratches.
The Washlet is an electrical product. Please be very careful not to let water get inside it. Please wipe
detergent away completely so that no residue remains in the gaps between surfaces.
Please note!
The toilet seat and lid can be removed easily so that
they can be cleaned thoroughly.
The use of excessive force during cleaning can
cause the toilet seat or lid to come off.
If the toilet seat or lid comes off, please refer to
Page 27 to reattach them.
Please note!
When using harsh toilet bowl cleaners…
When using detergent or disinfectants for toilets inside the toilet, please leave the toilet seat and
toilet lid open and clean the Washlet surfaces quickly (within three minutes).
Additionally, please wipe away all trace of detergent from the toilet itself.
(Vaporized gas from detergents used on toilets can get inside the Washlet and cause
malfunctions.)
Maintenance
DISCONTINUED
26 27
Thorough Cleaning of the Product
Cleaning the Washlet main unit, the toilet seat and lid
● The toilet lid and seat can be removed, so the every surface of the unit can be cleaned.
Open the toilet seat and lid and
raise the seat lock (grey) until you
hear a "click."
Removing the toilet seat and lid
Place the toilet seat/lid on the
toilet as shown in the diagram.
Take hold of the toilet seat and
lid at the base.
Align the toilet lid with the top
side of the seat sensor window
(black).
Pull straight up on the toilet
seat and lid with both hands.
Clean the main unit as well as the
toilet seat and lid.
Please clean within the guidelines offered under
"Daily Care and Maintenance" on page 25.
✲ The toilet seat cord can only be pulled
approximately 2 inches (5 cm). Please do not
use excessive force when pulling. (It could
cause a broken electrical connection.)
✲ Please do not pull up at an angle or use
excessive force. (Otherwise damage could
result.)
The toilet lid can be removed from the toilet seat.
[Removing the lid]
Place your finger on the seat lock on
the right side and move the hinge
module toward the inside
(approximately 2 inches (5 mm)).
Remove the toilet lid from the toilet
seat.
❈ The seat lock and hinge module
cannot be removed from the toilet
seat.
[Reattaching the lid]
Align the toilet lid with the
toilet seat from the left.
Move the hinge module on
the right toward the outside.
Attaching the toilet seat/lid
❈
When these are not pointing up and down,
please press the button and ten
seconds later press the button.
Check that the toilet seat pins
are pointing up and down.
❈
If the seat lock is not raised all the way up,
it won't be possible to attach the toilet
seat/lid.
Check that the seat lock (grey)
is raised.
❈
Please attach the unit so that the blue line
of the toilet seat cord does not get twisted.
Align the toilet seat and lid with the top
side of the seat sensor window (black)
and push firmly onto the toilet seat pins
❈
If the seat lock won't go down, the toilet seat/lid
are not attached.
Please reattach the toilet seat and lid again.
Lower the seat lock (grey) firmly until you
hear a "click."
❈
Pressing into place at
an angle can cause
damage.
1
2
1
2
Maintenance
DISCONTINUED
28 29
Cleaning the gaps between the Washlet main unit and the toilet
(About once a month)
● The main unit can be removed to clean the upper surface of the toilet and the lower surface of
the main unit.
Unplug the power cord
Other care and Maintenance
Cleaning and inspecting the power supply plug
● Please check the power supply plug around once a month to make sure that it is in proper
working condition.
Unplug the power cord
❈
Before removing the main unit, please be certain to
remove the plug for the automatic toilet flushing function.
Additionally, please make sure that no water gets on the
plug for the automatic toilet flushing function.
Remove the main unit
● With the main unit release button on the right side of the
main unit pressed, please pull the main unit forward.
❈
Please do not pull with excessive force because of the
water supply hose and the power cord.
Clean the area
● Please clean within the guidelines offered under "Daily
Care and Maintenance" on page 25.
Attach the main unit
Align the centers of the main unit and the base plate.
Slide the main unit along the surface of the toilet and
press all the way into place until a "click" is heard.
Press the automatic toilet flushing function plug into the
main unit.
❈
At that time, please make certain that the plug is not wet.
❈
If the main unit is not securely on the base plate, the
Washlet will not function.
Clean
● Please remove any dust that is on the blades of the plug
using a dry cloth.
Plug the power cord in
● Please plug the power cord in securely, all the way to the
base.
Cleaning the deodorizer filter (About once a month)
● If an odor is smelled, please remove the main unit and clean the deodorizer filter.
Remove the deodorizer filter
● Please press on the clip at the end of the filter
and pull it forward.
Clean
● Use a toothbrush or similar implement to
remove dust on the filter.
Attach the deodorizing filter
● Hook the left side of the filter onto the main unit and
slide the filter securely until you hear the clip "click."
❈
Never use the Washlet without a filter. (It could cause
malfunctions.)
Cleaning the wand
● The wand can be extended without spraying warm water, which makes cleaning easy.
Extend the wand
● Please press the button on the remote
control.
Clean
● Please wipe away any dirt with a soft cloth.
❈
Please do not pull the wand with excessive
force or push against it.
(Otherwise, malfunctions could result.)
Store the wand
● After about five minutes the wand will store itself
automatically.
The wand will extend.
1
2
● Please press the button again.
The wand will store itself and then
wash itself automatically.
2
Water will spray from the base of the wand as part of the cleaning process.
1
Cleaning the filter.
● The filter can be washed in water, but please remove any moisture before replacing it.
We recommend replacing the filter when it becomes soiled or blocked.
1
2
3
Maintenance
DISCONTINUED
30 31
Cleaning the water supply filter
● If you feel as though the water pressure for washing has weakened, please clean the water
supply filter.
Turn off the water shut-off valve
and the junction valve.
● Please close the junction valve with a flathead
screwdriver.
● Turn the toilet tank lever and run the water out of the
tank. (This will relieve pressure in the water supply hose.)
Open the cover (grey) using a flathead
screwdriver.
Remove the water drain valve with the
water supply filter.
● After loosening the water shut-off valve (with water
filter) please pull on it to remove it.
Caution
Do not remove the water shut-off valve (with
water filter) when the shut-off valve and junction
valve are opened.
Prohibited
Clean
● Wash and remove sediment blocking the filter with water.
❈
For fine sediment, use a toothbrush or similar implement
in order to remove everything completely.
❈
Please use a cotton swab or similar implement to remove
sediment that is caught in the hole for the water drain
valve (with water filter).
Install the water drain valve
(with water filter)
● Push the water drain valve (with water filter) into place
and tighten securely using a flathead screwdriver.
Caution
Tighten the water drain valve (with water filter) securely.
● Failure to tighten it securely could result in leaks.
Prohibited
1
Cleaning the filter.
● Please use plain water (without detergent) for washing.
● Please do not remove or break the filter.
We recommend replacing the filter when it becomes soiled or blocked.
1
To access the “junction valve” filter, the junction valve cover must be removed. Use a large flathead
screwdriver or coin and turn the valve cover counter-clockwise.
Place a container underneath the junction valve.
After removing the junction valve cover, gently pull the strainer out.
Clean the filter.
Remove sediment from the strainer using a
toothbrush.
Insert the junction valve cover with filter.
Push the junction valve cover with filter into the junction valve and turn it clockwise. Be sure to tighten
it securely.
Open the water shut-off valve
and junction valve
● Please open the junction valve with a flathead
screwdriver.
❈
Please make sure that there is no water
leaking from the water drain valve (with water
filter) or from the junction valve cover.
Close the cover (grey)
Maintenance
DISCONTINUED
32 33
Push the button on the remote
control. (Remove the residual water in the product
interior.)
Open up the cover (grey) using a flathead
screwdriver.
After loosening the water drain valve (with water
filter) using a flathead screwdriver, pull it out.
Prevention of damage due to frozen
water pipes
When freezing is anticipated
Please warm the bathroom interior when the ambient temperatures are expected to be sub-freezing. Or, when that is
not possible, please remove the water from the system.
When there is risk of freezing, please prevent it by taking the following steps.
If the product freezes, the unit could be damaged, resulting in leaks.
1
Removing water from the toilet tank
2
Removing the water from the hoses
Water removal
Before doing any freeze prevention
measures, please close the toilet seat and
lid.
Shut off the and
and then close off the toilet seat and lid.
Please take
note!
1
Turn the toilet tank lever and remove the water from the low tank.
2
Caution
Do not remove the water drain valve
(with water filter) while the water
shut-off and junction valve are open.
● Otherwise water will spray out.
Prohibited
Make the water supply hose horizontal and
remove the water from inside the hose
(approximately 1 oz. (30 ml)).
2
Please keep the toilet tank lever turned until the toilet tank water has completely emptied.
1
When freezing temperatures are anticipated
Please do not use the power saving features. The product could be damaged by freezing.
See Page 22 about stopping the timer power saver. See Page 23 about stopping the auto power saver.
Press the button once more.
(The wand will retract.)
Push the water drain valve (with water filter) into
place and tighten securely with a flathead
screwdriver.
Caution
Tighten the water drain valve (with
water filter) securely.
● If not tightened securely, there
could be leaks.
Mandatory
3
Keeping the Washlet interior warm
Be sure that the button is set to "on" and that the toilet seat temperature setting on the remote
control is set to "high."
Close the toilet lid.
Procedure for long periods of disuse
1
Remove the water in the toilet tank. Page 32
● When not using the Washlet for extended periods, changes in the water could cause skin
inflammation. There is also a chance that the product could freeze, so please remove the
water.
Removing the water
2
Remove the water in the hoses. Pages 32 to 33
3
Unplug the power cord
❈
Please be sure to unplug the power cord before removing the
main unit of the Washlet from the toilet.
4
Remove the Washlet main unit
See Page 28 for removal of the main unit.
❈
Please place the Washlet on top of the toilet at the front.
3
■ When leaving a site for the winter
■ When using at a cabin or other location
Please remove the water! There can be severe cold spells during wintertime absences.
Please be sure to remove the water in order to avoid freezing.
Replace the cover (Grey)
Turn off the water supply by turning off the water shut-off valve and the junction valve.
● Please turn off the junction valve with a flathead screwdriver.
1
2
3
4
1
2
3
5
6
7
1
2
Troubleshooting
DISCONTINUED
Troubleshooting
Please check the following before calling for service.
If that doesn't solve the problem, please Call TOTO U.S.A., Inc. Technical Support at (888) 295-8134
Caution
Whenever there is a leak, turn off the
water shut-off valve and junction
valve to stop the supply of water.
Mandatory
Please check the following before requesting repairs.
General
Doesn't work at all
Is there a power outage or a tripped circuit
breaker?
Are all of the LEDs on the main unit display out?
Has the main unit slipped off of the base plate?
Please wait until the power is restored.
Or, set the circuit breaker to "on."
Please press the Power on/off button
on the main unit control See page 13.
Please remove the main unit and
reattach it to the base plate.
See page 28.
Problem Possible Cause Solution
Rear cleansing / front cleansing
Has the water been shut off?
Are the water shut-off valve and junction valve
closed?
Is the toilet seat sensor working properly?
Is the pressure set too "low? "
Is the water supply filter blocked?
Is the water temperature set to "off," or to "low?"
Press the stop button and wait for the
water to be turned back on.
Please open the water shut-off valve
and the junction valve. (See page 13.)
Please read the section about the
seatsensor. See page 41.
Please press the water pressure
adjustment button on the remote
control. (See page 14.)
Please clean the water supply filter.
Page 30
Use the buttons on the remote
control to adjust it. Page 16
Problem Possible Cause Solution
Water will not spray.
The water pressure is
low.
The cleansing water
is cold.
34 35
5
Move the drain lever to the open
position and drain the water out
of the main unit.
6
Return the drain lever to the "closed" position.
7
Attach the main unit.
See Page 28 for attaching the main unit.
8
Pour antifreeze into the toilet
❈
The drain lever will not work unless the main unit is
removed.
●
The water (approximately 1 fi oz. (40 ml)) will drain into
the toilet from underneath the main unit.
1
Open up the water shut-off valve and the junction valve
Replenishing water following removal
●
Please open the junction valve with a flathead
screwdriver.
❈
Please confirm that no water is leaking from the
main unit or hoses.
2
Plug the power supply cord into the outlet.
3
Spray water out of the wand
●
Cover the seat sensor with white paper and spray water from the wand by pressing the , or
button. (Please catch the water in a paper cup or similar container.)
1
When the residual water is frozen and the water won't run, please warm the toilet interior the supply hoses
and shut-off valve using cloths immersed in hot water.
1
Troubleshooting
DISCONTINUED
36
37
Deodorizer
The deodorizer
doesn't work
Is the seat sensor working properly?
Is the deodorizer filter blocked?
Under the following circumstances, the seat
sensor may function, triggering the deodorizer. It
is not malfunctioning.
● When standing in front of the Washlet.
● During cleaning
● When the toilet tank lever is operated, etc.
Please read the section about the
seated sensor. Page 41
● Please clean the deodorizer filter.
Page 29
● If odor is still a problem even after
cleaning the deodorizer filter, call
TOTO technical support.
—
Problem Possible Cause Solution
It sometimes doesn't
remove much odor
Energy-saving function
The Auto energy
saving does not work
even after the button
is pushed
It takes two or three days to determine the time
periods when the toilet is not used very often.
When the same time period is used about three
times a week, the power saving will not work
during that time period. It is not malfunctioning.
Is the power cord unplugged or has there been a
power outage?
Did you replace the batteries in the remote
control, unplug the power cord was or have a
power outage? (If so, the time settings may be
incorrect.)
Did you replace the batteries in the remote
control?
(The settings may have been reset.)
—
—
It may not function properly that day,
but it should be functioning properly by
the next day.
Please press the Timer on/off button or
the Auto on/off button on the remote
control and reconfigure the settings.
Gradually, it will save power during the
correct times. Pages 21 to 23
Please press the Timer on/off button or
the Auto on/off button on the remote
control and reconfigure the settings.
Pages 21 to 23
Problem Possible Cause Solution
The energy savers
don't start at the
correct time.
Energy saving does
not occur
Rear cleansing/front cleansing
The cleansing water
turned off early.
The , and buttons turn off
automatically after around five minutes.
Is the seat sensor working properly?
When the seat sensor functions, it runs the
water to prepare to spray warm water.
Additionally, changing position while seated can
cause the seat sensor to turn on or off, causing
water to flow for several seconds from around
the wand. It is not malfunctioning.
Please press the , or
button again. Page 14
Please read the section about the
seated sensor. Page 41
—
Problem Possible Cause Solution
Heated toilet seat
The toilet seat
doesn't get warm
Is the toilet seat temperature set to "off" or
"low?"
Is the unit in timer power saving?
Is the unit on auto power saveing?
About one hour after sitting on the toilet seat, the
toilet seat heater will shut off. If you move away
from the toilet, the toilet seat heater will turn on
again automatically.
Please make adjustments using the
buttons on the remote control.
Page 16
After sitting on the toilet seat, the
heater turns on and warms up in about
15 minutes. Page 21
After sitting on the toilet seat, it will
warm up temporarily. Page 22.
—
Problem Possible Cause Solution
The toilet seat is cold
Dryer
The dryer temperature
is low
Is the dryer temperature set to "low?"
The dryer stops automatically about 10 minutes
after pressing the button.
Is the seat sensor working properly?
Is the seatsensor working properly?
Please make adjustments using the
buttons on the remote control.
Page 16
Please press the button again.
Page 15
Please read the section about the seat
sensor. Page 41
Please read the section about the seat
sensor. Page 41
Problem Possible Cause Solution
The dryer doesn't
work at all
Troubleshooting
After sitting on the
toilet seat, water
flows into the toilet
from around the wand
for several seconds.
Deodorizer starts on
its own
DISCONTINUED
38 39
Auto open/close
The toilet lid doesn't
open/close
automatically
Is the auto open/close set to "off?" (When set to
"off," the text "lid open/close" will not appear on
the remote control display.)
Is the "sensor" LED on the main unit display
turned on?
Are you standing somewhere other than directly
in front of the toilet?
Is the seat sensor or the person detection
sensor working properly?
Is there dust or debris on the seatsensor or the
person detection sensor?
Are there any interior features or decorations on
the door or wall directly in front of the toilet?
Is the "sensor" LED on the main unit display
turned off?
The toilet lid will not open automatically again, if
you are standing directly in front of the toilet.
The seat sensor and the person detection
sensor may have trouble functioning depending
upon the manner of sitting, stance, color of
clothing, fabric etc.
Is clothing covering the seat sensor or the
person detection sensor?
Is there debris or drops of water on the seat
sensor or the person detection sensor?
If the toilet lid runs into something the first time
that it opens after the power cord is plugged in, it
may stop opening (or close) before opening
completely. (It stores the position from the first
time it opens.)
Push the Auto on/off open/close
button on the remote control and set it
to "on." Pages 17, 18
Please stand directly in front of the
toilet. Pages 17, 18
Please read the section about the
seatsensor. Page 41
Please remove any debris, drops of
water, etc.
Please change the position of the
interior feature in question.
Please move away from the toilet and
wait 90 seconds. Pages 17, 18
Please try sitting squarely on the toilet
seat, changing your stance or
rearranging your clothing so that the
sensors can detect your skin.
Please move the clothing out of the
way and remove any debris, drops of
water, etc.
Remove any obstacles, unplug the
power cord, plug it back in and then
press the [graphic] button on the
remote control. Page 17
Problem Possible Cause Solution
The toilet lid closes
on its own
Troubleshooting
When the toilet lid is
opening, it starts
closing early (or else
it stops)
Automatic toilet flushing
The toilet doesn't
flush automatically
Is the auto toilet flush set to "off?" (When set to
"off," the word "flush" will not be visible on the
remote display
After an automatic flush, the toilet won't flush
again automatically for about 60 seconds.
Is the seat sensor or the person detection
sensor unable to function properly?
<When the toilet lid is up>
When seated on the toilet seat and flushing
using the remote control, the automatic flush
doesn't work. However, it will flush automatically
if the seat sensor detects someone's presence
for 60 or more seconds.
<When the toilet lid/seat are up>
When seated on the toilet seat and flushing
using the remote control, the automatic flush
doesn't work. However, it will flush automatically
if the seat sensor detects someone's presence
for 60 or more seconds.
Is there dust or debris on the seat sensor or the
person detection sensor?
<When the toilet lid/seat are up>
Are there any interior features or decorations on
the door or wall directly in front of the toilet?
<When the toilet lid is up>
The toilet won't flush automatically when seated
on the toilet for less than six seconds.
<When the toilet lid/seat are up>
The toilet won't flush automatically when
standing in front of the toilet for less than six
seconds.
<When the toilet lid/seat are up>
Is the "sensor" LED on the main unit display
turned off? The toilet won't flush automatically
when standing directly in front of the toilet.
Push the Auto on/off Flush button on
the remote control and set it to "on."
Pages 19, 20.
Please flush it using the button on the
remote control. Pages 19, 20.
Please read the section about the seat
sensor. Page 41.
—
—
Please remove any debris, drops of
water, etc.
Please change the position of the
interior feature in question.
Please remain seated for at least six
seconds before standing from the
toilet. Page 19.
Please move at least 1 foot (30 cm)
away from the toilet after standing for
at least six seconds.
Please move away from the toilet and
wait for at least three seconds.
Page 20.
Problem Possible Cause Solution
DISCONTINUED
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
Toto Washlet S400 SW563 User manual
- Type
- User manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Toto NEOREST MS950CG User manual
-
-
Toto NEOREST User manual
-
-
-
-
-
Toto SW573#12 User manual
-
Toto WASHLET TCF4721U User manual
-
Other documents
-
Moen 21334 User manual
-
bathstore 41100060930 User manual
-
Kwikset 300CV11P4PK User manual
-
iTouchless TS1RWAC Troubleshooting guide
-
Woodbridge LT507 Operating instructions
-
Drive Raised Toilet Seat User manual
-
Woodbridge T -0008 Toilet & Bidet Installation guide
-
bioBidet BB-1000R79283 User guide
-
Woodbridge B0970S Installation guide
-
Sharper Image Motion-Activated Flushable Wipe Maker Owner's manual
